WOW Someone on YT can actually weld with a flux! I've just watched every pred go kart swap nothing but piss-poor welds so Its refreshing to see! Good work and great design.
Welds look far better than anything factory from Yerf-Dog. Peerless Gear has a series 100 differential that you might consider for a future modification.
@@user-cc7be8bu2j www.gopowersports.com/3-hole-1-axle-bearing-kit/. These will attach to the stock locations without a problem as long as you have a one inch axle.
@@user-cc7be8bu2j use lock collars on either side of the bearings www.gopowersports.com/1-axle-split-collar-1-4-keyway/?campaignid=17318042849&adgroupid=&adid=&gclid=CjwKCAjwo9unBhBTEiwAipC11543CDY-GBnB_xNGOF_VKXtDEQj-nHz42yJoerWFsRhtbJrOOEagLRoCJXcQAvD_BwE
I used the stock disc and attached it to this. most of the holes aligned up, I had to drill one or two holes in the mounting hub. just make sure the disk is perfectly centered on the hub. you may have rotate the disk to get most of the holes to match up. I use 1/4 inch nuts as spacers all around the center of the disk to keep it centered in the middle of the hub. www.gopowersports.com/1-sprocket-and-drum-mounting-hub/
WOW Someone on YT can actually weld with a flux! I've just watched every pred go kart swap nothing but piss-poor welds so Its refreshing to see! Good work and great design.
Welds look far better than anything factory from Yerf-Dog. Peerless Gear has a series 100 differential that you might consider for a future modification.
Excellent work!
Im going to make the same thing but for my golf cart but it will have reverse. Perhaps a mass produced conversion for golf carts.
Nice job
nice welds
How much did you cut off the center cross bar
Have to have a trailer hitch
Just subscribed, your videos are very helpful. Did you use the stock hub mounts? What did you use?
Thanks, these are my rear hubs www.bmikarts.com/White-4-x-4-Wheel-Heavy-Duty-Hub-1-Bore_p_1662.html
Im sorry I meant the axle, what did you use to mount the new bmi axle to the frame. @@justinsauer5682
@@user-cc7be8bu2j www.gopowersports.com/3-hole-1-axle-bearing-kit/. These will attach to the stock locations without a problem as long as you have a one inch axle.
@@user-cc7be8bu2j use lock collars on either side of the bearings www.gopowersports.com/1-axle-split-collar-1-4-keyway/?campaignid=17318042849&adgroupid=&adid=&gclid=CjwKCAjwo9unBhBTEiwAipC11543CDY-GBnB_xNGOF_VKXtDEQj-nHz42yJoerWFsRhtbJrOOEagLRoCJXcQAvD_BwE
awesome, thanks for being super helpful! @@justinsauer5682
What size sprocket di you use? And can you put the link?
www.bmikarts.com/40-Sprocket-60T-with-1-Hub-_p_1415.html?gad_source=1&gclid=CjwKCAiAs6-sBhBmEiwA1Nl8s6rXEQqOO-R1EjyEZjBiCw5oxFCsyQ2cLUNV-yR13iqh3apYOMQIixoCZh8QAvD_BwE
Where did you get the axle from? I have a yeti dog 3209 tryna do the same thing with swapping to a predator
BMI karts 1" live axle 45" I think.
I just bought a yerf dog and would like to know what axle you bought and where did you get it?
Bmi karts 45 inch 1inch diameter www.bmikarts.com/1-Steel-Live-Axle_p_517.html
What rear brake rotor and rotor mount did you use?
I used the stock disc and attached it to this. most of the holes aligned up, I had to drill one or two holes in the mounting hub. just make sure the disk is perfectly centered on the hub. you may have rotate the disk to get most of the holes to match up. I use 1/4 inch nuts as spacers all around the center of the disk to keep it centered in the middle of the hub.
www.gopowersports.com/1-sprocket-and-drum-mounting-hub/
I want one.. what is the price
ЕСЛИ ЕСТЬ УЧИТЕЛЯ-ЗНАЧИТ ДОЛЖНЫ БЫТЬ УЧЕНИКИ!
What???
@@justinsauer5682 Fuck it all....copy and do
What size axle did you get?
1 inch diameter 45 inches long. BMI Karts
Thanks
Why doesn't anyone give them flex or something on the rear it would something new to see
Huh?