Is this tool as good as the Turbo Decoder ? @ $90 USD
Vložit
- čas přidán 11. 05. 2021
- Is this tool from NP just as good as the Turbo decoder? In this video, I will try the new tools I just received. The tools were about $99 USD + post, this is the first tool and the first time using the tools and the review on the tool.
#NPTool #CarLockPick #NPProfessionalLocksmithsTool
Buy locks - Lock Shop #LockShop www.drlock.com.au/store/lock-...
Car Key Copy #carkeycopy www.carkeycopy.com.au/
Locksmith Hornsby #LocksmithHornsby www.locksmithhornsby.com.au/
![[375] Unboxing Some Of The Most Useful Lock Picks In North America | Lishi Pick and Decoder](/img/n.gif)
I only just came across this video, the tool has to be the right way up, once it’s in, pull the sliders back and give the tool a pull, if it moves out at all, it’s upside down. Try again.
Once it’s in properly, twist left and right but also up and down, not left and right against the blade but up and down, twist left and right. Usually doesn’t take more than 10 seconds.
Good luck, I love these tools 🤞🏼
I wish I knew that from the start, I will have to give it another go, thanks for the info
I agree. I used the same thing, but it didn't turn just left and right. Thinking about it, I added up and down movements and it turned around. The attached video has the same behavior. I hope it will be a hint
czcams.com/video/5sJkI3WO3UU/video.html
I broke two of these inside the door lock.. Garbage tools. The pins on the tools are extremely stiff. Bad design. Won't recommend any one buying
I see that you have the mini prog just sitting there on the side lol. PLS make a video on it when you can.
You have the tool in the wrong orientation,The key that comes with it is to let you know which way the tool goes into should have a little dot on the side.
I have simmilar, black with Mr Li logo, I managed only to open 1 golf5 lock in less than 10 seconds, need to be inserted right way, the oldest won't go. You need to put little pressure left and right and holding in those positions move down and up. I think is only good gen 3 hu66
When you insert the tool, pull the sliders back, then pull the tool back, if the tool moves back it's the wrong way, turn the tool around then try again
Not a reset key but a key to tell you which way round to insert the tool!! When the key goes fully in make sure the dot on the tool is on the same side as the dot on the key. You can also insert the tool, pull the slider then pull the tool, if it comes out 4-5 mm the tool is upside down.
Does it work only one way or does it go in ether way, are both sides interchangeable
Does it work on just one side or both sides of the pick ?
Have another go and do another video it does work
czcams.com/video/CGVTOIhE1ik/video.html
😂🤣
Are each side interchangeable?
I must admit you had tool wrong way round at 1st !...I have brought the same style hu66 tool , it never opened the lock, always over set some pins pass where they were suppose to be.Also the more I tried the tool started to twist in the handle ...not that good in my opinion
How to open this cylindar??
Did you ever get this to work ?
Hope this helps post a new video if you can after you watch video I sent you should have no problem with the tool
Wher may I purchase this?
Have you got it up the right way?
It looks like you have to get it set up for the correct wafer configuration
up,up,down,down,up,up,down,down
NOT
down,down,up,up,down,down,up,up
What lock is that? Not from your part of the world, that looks like a Golf Mk7 door lock which would be HU162 not HU66. But your key looks HU66 so I suspect you’re good. But is it HU66 Gen1 or Gen2? The reason I ask is I had trouble with mine until I realized my practise lock was a gen1 HU66. It had up,down,up,down,up,down,up,down wafer configuration rather than the up,up,down,down,up,up,down,down this tool works on.
Felt like an idiot but it’s working fine now.
That generational difference between where the wafers are ganged up - that'll be the death of me soon
Como eu faço pra comprar
Have another go
👍♥️♥️♥️♥️♥️♥️♥️👍
Have you tried the vapon katana???
no I have not, any good ?
@@DrLockShop I just ordered two of them. I guess we will see!
@@jonyovanno4145any update？
I had the same problem at first.
Till I learned it was upside down.
Trick is when you turn tool and it pull back its the wrong way round.
I wish I had knowen, I returned mine :(
@@DrLockShop yeah I thought the same till I played around with it.
It opens up every motor I use it on now.
And does the ignition lock straight away.
I buy salvage vehicles and most have no keys.
But it's saved me thousands of pounds on locksmiths and I got the bmw and mini tool does the same thing.
Works the same way if its lose in the lock turn it around.
Great investment for the car trade 👌
That’s really upsetting to buy a tool that doesn’t work...
This is a impression tool
do you use it, dose it work for you, whats you tool of choice
@@DrLockShop no i use lishi im a master with the lishi but i was thinking about ordering a few of them picks you used in your video to try out. i sent you a video link watch it for tips on that tool it will help.
La++++
BE WARNED. The very first time I used one of these on a customers car it became stuck in the barrel and I struggled for over an hour to remove it. Will never use it again as its ended up in the bin. Very untrustworthy piece of junk
Одноразовый
I got a refund
another tool for the junk
Talk waaaaaaaay too much