Correct me if I am wrong, the flywheel is like an energy storing device like a battery. So let us consider the same setup that you used wherein you use a motor to rotate the flywheel. In simple words you are transferring the mechanical energy of the motor to kinetic energy of the flywheel. Now after the flywheel or "battery" has reached to its full kinetic energy or "charge" by the motor or the "charger", you are turning off the motor or "charger" and therefore the flywheel continues to spin due to moment of inertia therefore dispensing its stored kinetic energy or "charge". At this particular instant, the input to the entire setup is 0 watts but the output by the generator is say whatever the capacity of the alternator/PMG is. So, my question is this power multiplication? Because to me it sounds like you're storing energy and using that same energy. I would rather call it much worse because here we would have to consider much more inefficiencies like the motor will have some losses, switching losses of VFD, frictional losses by the bearing, static losses by flywheel. So, what energy you dispense by the motor, which then is stored by the flywheel and then is fed to the alternator/PMG, there is a drop in energy at each stage due to these losses. Now, let us climb another step further wherein you mentioned the smaller motor is running. Imagine that the system is fully charged (meaning flywheel is rotated to its rated capacity) and now the alternator is in mesh with the flywheel and there is an instantaneous full load connected to the alternator/PMG. In this case there has to be an obvious drop in speed (RPM) of the flywheel. Now as suggested the lower capacity motor will run and make up the "RPM's" lost. Now won't the smaller capacity motor need to dispense an equal amount of energy to "charge" this flywheel bank? Or rather we can sum it up like the higher capacity motor is a "fast charger" and the lower capacity motor is a "slow charger"? Now to take it another step further the losses of the smaller capacity motor is to be also considered. Also, not to mention that your alternator/PMG is always meshed, needless to say, even they have losses to be considered. In my opinion I would rather call this an uninterruptible power supply, where you charge a battery and use it when the power goes or there is a low voltage! So, my conclusion on this is that flywheels are to be used to avoid "jerks" in the supply system and not to multiply or generate power.
😂😂 exactly it's just onether misunderstanding of simple energy conversion.. fly wheel is just a power storage device.. there were even vehicles in the 1940s that used it but it was so inefficient.. he could just call it power divider instead of multiplication
Your talking is very exaggerated about the losses !!, ( The bearing losses are also very small ) There are also no (frictional losses) except with air(still small), but there are losses due to magnetic fields and Eddy currents ! generally, The motor/generator is known for its high efficiency. yes, the Flywheel consider as power multiplication because it gives more energy than you put into it !
This is NOT AN ENERGY MULTIPLICATION POWER SYSTEM but can be thought of as an ENERGY STORAGE SYSTEM. To be more specific, we can use this system to trap or hold the mechanical energy using fly wheels of minimum rotational friction (of-course with an exponentially but slowly decaying fashion) for some time. Can be a very good energy storage system (may be comparable to batteries) to hold the power generated during day time when using solar power panels. This system can slowly release the energy to a connected load during night.
@@harrytopia282 Yes, huge flywheels on gigantic metal stamping presses will coast to a stop in a few minutes after the power is shut off and they are even running without a load on them.
@@harrytopia282 I agree with you . Arrest deceivers off CZcams pronto before more young minds are destroyed and their wallets and wasted time. There is no free lunch in the universe.
this is actually really impressive. Those bearings are a very good engineering design choice same with the flywheels. Pulley and shaft shape could be changed for a more efficient energy transfer. Great job
This certainly is a great example of energy storage, but not “free energy”. One thing I did not hear you comment on is mechanical losses. There is friction here... there has to be. This machine is also extremely dangerous. How it was balanced would appear to be pretty scary. That welded plate on the wheel is representative of an effort... but...
After your success my selute to you sir getting patient is your biggest achievement. Now it's our government's responsibility to bring this technology to everybody's life. 👍
Multiply Input voltage with current to calculate input power. then use the same way to calculate output power. Now you have to consider the time. I mean calculate the Watt hour. compare Input watt hour with output watt hour, then you will see output watt(load) is decrease as stored energy in the fly wheel is finishing. Which makes you understand that it is not possible to generate more power than input. You should start studying both mechanical and electrical engineering.
That's a GREAT idea: 1) store some energy in mechanical form 2) recover it during a demo showing off whopping numbers. 3) pocket the money from inedicucated investors. PURE GENIUS!
So if I understand this right, the energy to maintain the rotation of the flywheels is less than the energy that can be used to generate power. Your energy loss is condensed to the initial start up of the flywheels, which is significant, but once the flywheels are in motion your input is less than the output. This is still an energy storage device in practicality, but that in itself is very valuable. Imagine scaling to the 100 ton flywheel size, and using mechanical wind power through a variable gearbox to increase the RPM of the flywheels during peak wind. Then you could draw electricity from a series of generators when needed at a variety of voltages at what ever amps needed at the time. Even excess Photo-voltaic energy could be used to increase the rpm during peak sunlight periods . With these two energy sources producing the power to generate the RPM the generators would slowly reduce the RPM when producing electricity on demand. There is not a total energy multiplication, once you take in the start up energy needed, but it is an excellent way to store the energy from wind and solar, both of which are variable. Keep up the good work
@CNC Basic If you understand vector and scalar forces. Gravity is a vector force. You know what it means? Certainly no. When you refer to energy you are talking about a scalar force.
@CNC Basic You skipped Biology classes as well? If yes do some research in Internet. Have you heard about motor nerve3, spinal cord, Nerve cells and Brain. I don't want to Physics and Biology classes. You stay in your ignorance. Good for you.
Energy in = less energy out (loss due to friction etc). The form of energy does not matter. So there is no power multiplication. Though energy storing in an 8 ton flywheel is a good idea. You can rotate the flywheel (when the bearing is ok) by hand or a few Watts source, you don't need 20 Kilowatt to make it spin. So that does not tell something about efficiency. Input amp = 15 A and output Amp is 28 A, that also does not tell anything about efficiency and input power versus output power. Watt = Electrical Power = Volt x Ampère (DC situation). Anyway: a good idea to store energy this way.
yes, same thinking.. he is saying that we are having more enery out than input, 15A in 28A out, but he is missing that what he is getting out he stored that energy in the system at the beganing. i think he is engineer but i just can't understand how he missed that. but as u said it is ok to store the energy, like a bigg capacitor in electronics
When I was at School in the 90's I asked my Physics teacher about this concept, I was reminded of the laws of conservation, and the class carried on. I knew it was a good idea! Scaled up, with gearing, this concept will rock!
Who made the law of conservation?? Human or God?? Who can make law?? If God make the law I will accept. If human made the law - I will say that is cheating.., because of fuel Market. I
@@anbarasanstalin5998 the law of conservation of energy is not a legal law, its simply a description of reality. Energy can be converted from one form to another, but never lost or created out of nothing. Its just how shit works.
@@anbarasanstalin5998 This guy @brahm-ahamasmi should change his name to Scientist-o-Asmi.... These people desecrate Hinduism by keeping such names....
I am a Industrial Electrician and have been for 45 years and am highly experienced with large electric motors , generators , alternators and especially Variable Speed Drives (VSD) . Now ...... The only energy input into this "machine" I can see is the large 3 phase motor (light green) which is supplied thru the large VSD in the building which allows them to control the speed of the whole system . Huge concern !!!! I see no earthing or machinery bonding what so ever . Very disturbing . No true electrician was involved in hooking up this debacle. He is claiming that more energy can be derived from the assembly than is inserted from the large motor . NO! I estimate with the Vbelts , the very large bearings , even the motor and "Generator" bearings plus the wind resistance on the flywheels at least 15 to 20% of the energy (electric power going in) is consumed by these alone . It looks like he is claiming that when he revs up the flywheel with large motor , then turns that off and "runs" the system then with the little motor (never saw that) then he can connect the generators and pull free energy out of the system , NO NO NO NO he can't , and I suspect as the flywheels run down ,as they will, he has connected a generator to the flywheel and its output to the "small electric motor and thinks that will keep the system running (it won't) .. If he believes that and he seems to have convinced a whole lot of people of such a miracle including the Telengana state government by inviting him to exhibit his invention on independence day celebration, he is either one of 2 things . Extremely naive and dare I say "stupid" certainly not an engineer or he is a con man ! This is an energy storage device yes , very inefficient but yes ! But it is not and there is no such thing as a power multiplying device that can subtract energy out of nowhere and utilise it . There is a lot of power stored in the flywheels especially at 6000rpm (i wouldn't stand near it !) but that power /energy comes from the large electric motor initially and no where else . Throughout the whole universe the equation is : power in = power out minus loses (friction) . In that equation is the death of all perpetual motion machines !
all you say is theory and blah blah ... in all neutrality, if you think it is a scam then prove it, as he does by experience or otherwise you shut up. thank you
Sir,I tried this experiment,it didnt work,then I asked one scientist,he told me,we can never generate electricity ,with electric motor and dynamo interconnected,the forces will cancel eachother and become zero,this is because the more the electricity , motor draws ,the Tighter the dynamo armature becomes,and slows down the motor, and finally the motor comes to stop ,that is what that scientist told me. But with the help of flywheel if you are able to make it successful ,then it is a good invention,very good sir, keep it up.
What if we use electric generator to rotate a big flywheel in Vaccum. It will give enough momentum to generate electricity for 3-4hours enough for short powercuts. What do u think??
According to him This whole system × 24= 2 day continues flow of current... It Also enough rotate to power up the first one system , Can From the last one system.... He can also start a electric mill for whole hyderabad.... Iam positive about you good luck sir appreciate it
The higher out amps compared to input amps is one thing however, I am most interested in the "total" input energy vs total output energy using accurate and documented (recorded) measurements of all dissipated energies. I suspect that the stored energy in the flywheels presents the apparent 'free' energy gain. In effect you are likely just slowly running down the stored inertial energy of the flywheels. Thus you will only 'apparently' be able to generate 'free' energy for a constrained time period. This can be proven another way and that is by maintaining the angular velocity of the flywheels under heavy load and taking measurements under that condition.
A pendulam gives twice the energy that is input. This is not magic. The angular momentum of the rotating earth is transferring energy through gravitational force field. The fly wheel works similar to a pendulam.
You are talking nonsense. Of course you can get MeggaWatts of free energy just from the air. Only the electric lobby (and their corrupt governments) keeps us buying energy from their power plants. It is massive government conspiracy. They even changed the physic books and are force teaching in schools some fake laws of energy conservation, it is all lies. Flywheel will give you as much free energy as anybody needs.
This is the electrical equivalent of chopping a 2x4 block of wood in half and bragging that you've multiplied it into a 1x8. Having more current coming out than is going in is meaningless without a measurement of voltage at both sides, otherwise the high pressure nozzle on my garden hose is "multiplying" water because it comes out at high pressure.
I think he is using it for Momentum. Your 2x4 to 1x8block is like your saying it’s just as efficient for Amazon to deliver packages across states using small vans instead of Tractor Trailers. It’s going to take the same effort? So why not use the smaller option?
Interesting research! Keep up the good work. I'm sure in time you will improve the design close to perfection. In the meantime, I think I will stick to my LiFePO4 battery bank to store my access solar energy.
Mopuri Balu from puttaparthi. Chaganti sir, l respect ur hardwork. you are not generating new power.you just are storing grid/battery power in flywheel for sometimes.
I built exactly the same machine. The only problem is that I supllied 220Volt but it gives me 230 Ampers. So, from my calculations: 230A - 220V = 10 Watts of free power. When I divide it by 5 buckets of goat milk, I receive 1.5 pounds of square inch of energy per mile and that is a huge gain, even NASA has no such results. Correct me if I am wrong.
A cordless 10v drill can turn that wheel🤨 if that gentleman is bearly touching it and he makes it turn.. running a drill / small motor through a simple bicycle drive train would crack a few hundred rpm..while putting out + mega watt of axle torque you use to turn a HUGE flywheel..then take from the axle....stacking flywheels is like lever stacking....3 see - saw levers are pretty much the max...but wheels can have gear boxes....from 1 bike 1 man could probably slowly turn the London eye wheel after 4 or 5 increasingly bigger flywheels stacked..
Flywheels are used as a cheap and easy way of storing rotational power. The greater the diameter and mass, the longer it will rotate after power is no longer applied to the system. The flywheel will eventually stop rotating. I'm not sure if the presenter properly explained this.
What is new or special here? Off the shelf components (geni and motor) which all have specific losses in doing their work. (Eddy current , copper losses, etc.) Given you are throwing away this energy as you try to spin up the big flywheel you can never get it back. This system is good for an uninterruptible power supply that can keep supplying a continuous waveform during a short interruption of mains power while there is a switchover to battery power to spin the flywheel/generator until the utility power is restored. We had this technology where I work for years since the 1980s and that flywheel powered device which provided our sensitive technical environment with constant power was called a PILLAR system ( German Technology I think) and it used the flywheel effect to overcome losses in mains power for milliseconds while batteries took over in keeping the flywheel spinning at synchronous speed..There is no free power here and what needs to be calculated is the efficiency which is always less than 100% = 1.
This flywheel system was in use to get uninterruptible AC power supply in telecommunication system. The flywheel keep the driving shaft rotating during switch over from motor to generator through a magnetic clutch. (Old system)
I have designed an active steering wheel that once accelerated cannot stop its march, it is much lighter than that common steering wheel shown in the Video ... / I have combined the absolute movement, with the relative movement, the Potential of the gravitational force with mechanical energy The machine is universally applicable and infinite useful possibilities // Yo he diseñado un volante activo que una vez acelerado no puede detener su marcha, es mucho más liviano que ése volante común mostrado en el Vídeo... / He combinado el movimiento absoluto, con el movimiento relativo, el Potencial de la fuerza gravitacional con la energía mecánica La máquina es de aplicación universal y posibilidades útiles infinitas
So basically he is saying that he defied basic law of conservation of energy? Come on "free energy" is just a scam. Secondly ampere comparison is not accurate thing to do. Ampere has no significance without voltage. If he is true that output amps are higher than input amps, input voltage must also be higher so there's no free energy generated.
I was studying this system and in my case, I was astonished until I tried to grasp the whole thing. Then , here it goes the explanation for the analyzed system : Electric Generator (let's say 5 Kw @ 3650 r.p.m rated power) power is generated from a Motor which only provides ( let's say 3 Kw @ 1725 rated power) . At first glance it seems as if the system where generating (5-3 = 2 Kw) . However we must be aware that High Inertia Values from Flywheels impossed high loads to the motor . The motor tries to achive this exigent load varying its working point , reducing its rated angular velocity (increasing motor slip , decreasing for instance to 1600 r.p.m ) and when this happens , the current and obviously power comsumption will be increased to respond this higher than rated load. Depending on the motor kind this new working current could be as high as 5 times the rated current , so , It's normal that power consumption could be twice or three times the rated power for the motor . I stronly recommend you guys to watch an induction motor torque power curve. In conclusion , Motor really demands 6 Kw ( 2(double in demanding power ) * 3 (rated motor power )) . With this established , it is clear that we have not broken 1st thermodynamics rule : (Motor power = 6 KW ) = (Genarator power = 5 KW ) + (loses = 1 KW) As you probably know this 1 KW lose energy must include: *Friction with air. *Noise levels. *Mechanical transmission loses .... etc . Pd. It was really curious that in the video He measured Voltage and Current , but , unfornately he didn't measure the output voltage in the generator ... he did measured only the output current.... Looking forward to hearing some replies
In other words its, super high efficiency using the flywheel to scalp off exrtra energy that normally would be lost or unused How efficienct do you think it is...60 ..70...80...90...95.%?.cause that's a big ass fly wheel ....wouldn't want to be any where near that when the bearing fails.
आज से छ साल पहले जनवरी 2014 में यही आइडिया मैंने कुएं पर डीजल जनरेटर को चलते हुए देख कर दिया तो सब लोगो ने मेरी हंसी उड़ाई थी । आज इस वीडियो की लिंक सेंड करके बताऊंगा की में सच था ।। मुझे आज अपने आप पर गर्व हो रहा है 💪💪।।
6000 rpm on plummer blocks, I dought it I know of some car engines that don't rev that high. At first those flywheels looked as though they were only doing a couple a hundred rims. Those plumber blocks would overheat at 6 grand and fry the lube and then the bearings size and then the whole gizmo would just fly to bits with desasterous results, maybe 600 rpm is more likely and those big flywheels would have to be precisionly balanced otherwise any imbalance would shake the whole contraption to bits and I don't think I would like be near that thing when it's spinning at 6000 rpm and one of those flywheels decides to seperate and break free from that thing.
@@Lesdig891: " Where were you educated? " Why were you NOT educated? His points are spot on. If you're stupid enough to believe ANY of these free energy liars you deserve to waste money trying to replicate their garbage since you're obviously too stupid to understand there is no free energy from ANY of these stupid (and in this case and many others) dangerous contraptions.
@@lorditsprobingtime6668 chill out asshole hahaha it was a simple question I didn't dispute his points I was just wondering if he had a degree in mechanical engineering or something
@@Lesdig891 Your insinuation was that he's not qualified to have the opinion he has a hole. Now you're lying about your intent to 'try' and sound slightly more reasonable, you're just an idiot who wants to try and sound superior, screw you.
@@lorditsprobingtime6668 these people aren't building things and wasting their time and money because it doesn't work! These things work!! People generate power for their homes for free! I've seen many people build these types of things, they work!
This particular flywheel will keep accelerating, reaching 99% of the speed of light. Generating more energy than all the combined stars, black holes, aliens, pulsars, in the universe .
It’s essential to building a time machine since there’s no gasoline and electricity in the ancient past like whenever that WW II thing happened. Come on man! You know what I mean!
When this machine inaugurated and launched Iron Man and Spider Man will be there so that they can save our human life from extreme energy generation by this machine.
Flywheel energy storage systems using mechanical bearings can lose 20% to 50% of their energy in two hours. Much of the friction responsible for this energy loss results from the flywheel changing orientation due to the rotation of the earth (an effect similar to that shown by a Foucault pendulum). This change in orientation is resisted by the gyroscopic forces exerted by the flywheel's angular momentum, thus exerting a force against the mechanical bearings. This force increases friction. This can be avoided by aligning the flywheel's axis of rotation parallel to that of the earth's axis of rotation. Conversely, flywheels with magnetic bearings and high vacuum can maintain 97% mechanical efficiency, and 85% round trip efficiency. #Wikipedia# Flywheel energy storage has been used in public transport and even in mining vehicles. There is nothing nonsense in this contraption (well you have to turn volume to zero), only very low efficiency.
This is fascinating. I wonder if this concept can be modified to incorporate snowmobile-style CVT (Continuously Variable Transmission) Primary and Secondary clutches? Though the gearing changes are technically infinite, in reality, it's comparable to having, say, a 3-speed bicycle except no jarring gear changes are needed. I do believe the snowmobile belt design is superior to the standard V-belts used here as well, though finding them in the correct length needed for this application could be quite problematic. Of question would be if the benefits would overcome the increased complexity and friction due to more moving parts.
All of the stuff in this comment is true, although storing energy in flywheels is not the subject of the video. The video essentially claims that the efficiency is over 100% and is therefore creating energy. Energy storage in flywheels is ordinary, and is all that is happening in this video. Not only is no additional energy generated, energy is lost due to the forces discussed in the above comment. You can’t create infinite energy with flywheels, no matter how much you hope and dream about it.
@@GangsterBusiness flywheel vehicles are not new, I think in England , a flywheel based tram system was developed (I don’t remember the name of the town), but this was discontinued as it’s not a efficient system
Good Job Sir ! This American Salutes your Skills ! I am subscribing to your channel so I can see how you Engineer & Correct The Negative's !! ( Trial & Error ) is how we make things better !!
So basically he is saying that he defied basic law of conservation of energy? Come on "free energy" is just a scam. Secondly ampere comparison is not accurate thing to do. Ampere has no significance without voltage. If he is true that output amps are higher than input amps, input voltage must also be higher so there's no free energy generated.
Alhamdulillah saya waktu sekitar 2004 udah faham betul dengan teori ini hanya saja belum pernah praktek karena ga ada support. Malah pernah beberapa kali konsep atau gambar skema nya saya upload atau posting kala itu di Yahoo grup atau yahoo mailing list namun karena waktu itu sangat awam jadi ga pandai dokumentasi jadi ga banyak data yang dapat disampaikan saat ini. Waktu itu konsepnya PLTL Pembangkit Listrik Tenaga Listrik. Dinamo 200 watt (nyala awal pakai pln) gerakan 20.000 watt menggunakan dobel piringan besi atau baru baru ini saya baru tau kalo namanya sebutan nya playwheel gitu. Kalo waktu itu saya sebut dengan teori momentum sebagai penggerak utama nya. Mudah mudahan dalam waktu dekat bisa segera membuatnya dan dapat bermanfaat bagi masyarakat
Thank you Mr Changati and team. I am appreciative for this knowledge. Your work is very impressive indeed. As i child, when playing with small motors from toy cars, to my surprise i realized that when rotated, the motors lit small bulbs. The question is, is it possible to build durable units that can be connected and used domestically??? Am interested in doing this
So basically he is saying that he defied basic law of conservation of energy? Come on "free energy" is just a scam. Secondly ampere comparison is not accurate thing to do. Ampere has no significance without voltage. If he is true that output amps are higher than input amps, input voltage must also be higher so there's no free energy generated.
@@ndreddy8416 Hmm...but can be converted from one from to another. To Generate energy is the same accumulation of energy. What you probably meant was that energy can’t be created. The question is, how can this be achieved as cheaply and as efficiently as possible? I see a solar charging system somewhere. A unit or setup a peasant can run domestically. However much I ponder this, it seems to come down to cheap and yet efficient energy storage cells.
Thanks for such hard work, but two questions; 1, if your input is 20 KW, then how much is the output (sure, it should be more than output) and 2, when we use about maximum output of system, does the input machine support it? as I experienced it, it doesn't and gets slowly stopped..
Very Good Bhaskar If you were here in Brazil, a project like this in the industries here in my region you would sell quietly, very good. How many KWA does this plant produce?
I built a device once that had several disks all larger than the next. I think I had 10 in all. The smallest 4 inches and the largest 4 feet in diameter. Each disk had aluminum plates on the outer edge side facing the next larger disk. Each disk had magnets on the side facing the smaller disk place in the diameter of the next smaller disk. All except 2 of the disks were on a shaft with bearings that would turn independently of each other except for the largest disk was attached to the shaft. The very smallest disk was attached to a 9 volt motor about the diameter of a quarter. I would turn on the motor and it would spin. This would start the bigger second disk spinning and the second d would start the bigger third and so on. I was able to spin the 4 foot disk at about 135 rpm in the end. You could slow the largest disk with a load and have very little affect on the smaller disks. I have torn it apart and the rennets are still in my basement. I would love to see this built to low tolerance specs. Maybe even use copper plates or coils instead of aluminum plates. Mine was cut out on a table saw from 3/4 project board and some parts made on my cnc router to hold bearings and such.
hello I really appreciate your engineering design and you have explained your design extremely well and I'm feeling like I didn't get the generator output but I do observe your amp output and input please provide me the KW / Volts so that I can know this much better way
So basically he is saying that he defied basic law of conservation of energy? Come on "free energy" is just a scam. Secondly ampere comparison is not accurate thing to do. Ampere has no significance without voltage. If he is true that output amps are higher than input amps, input voltage must also be higher so there's no free energy generated.
Dear people, since electricity is supplied to remote villages with thin wires, it becomes impossible to use devices with a high peak load, this device was created for this. At the time of using high power, the shortage is covered from the energy that is stored in the flywheel.
After this particular invention, based on the pure science of miracle, India already closed all power plants. This flywheel alone, supplies enough free and green power to whole country. I just returned from travel to India and I did not see any power plants there, all generating plants have been closed and demolished, due to this particular free invention. All villages and cities have only flywheels produced by Mr. Chiaganti.
Energy can neither be created or destroyed. It's converted from one form to other. Current production is having a load of magnetic flux cut by coil. This action needs force. The stored energy in flywheel would get stopped when a good amount of electricity is produced in demand. Here load is lower than a certain limit which allows flywheel to roll.
May be this particular video is helping the particular people today to Research on this particular way of generating the free particular Electricity, and the video had used the word "particular" in such a particular way, but I'm shocked that nobody on this entire planet noticed the word "particular" in this particular video. I appreciate your particular idea.
It would be interesting to find out what increased efficiency could be experienced by adding mag lift components, which should eliminate some drag from the particular friction on bearings, etc. I find this kind of innovation very exciting.
Dear sir, in our workshop we achieved this with 2 meter in diameter and 4 tons in weight 100 kw is the storage of the flywheel. If the flywheel is 8 tons in weight minimum 3 meters and maximum 4.5 meters in diameter and rotated at 7000 rpm then the total weight required for generating 1.6 MW will be 70 tons . If each individual flywheel is 8 tons in weight and there will be 9 flywheels in total. Each wheel is attached with the other and one independent gearbox is fixed with the first flywheel and rotated by a 15000 kw Motor (Dual speed or 2 speed motor) there by all 9 wheels are rotated at 7000 rpm each wheel multiplied with 9 independent wheels there by total rpm will be 63000 rotations and the cumulative flywheels total torque is transferred to the 1.6 MW PMG generator with 750 rpm there by if we convert the rpm into (RPS rotations per seconds ) then the rps of the flywheels 1050 rotations and the PMG wil be 12.5 rotations per second. The torque of the generator is 20370.77 NM and the torque of the 15000 kw motor is 47744.00 NM. The 9 flywheels will keep on rotating for more than 3600 seconds and Free energy is generated. In put is just 10 seconds time for the 15000 kw dual speed motor to rotate 70 tons to 7000 rpm and leave it to rotate by itself on the plummer block bearings . Here if the 70000 kg weight is divided by 15000 kw power then we will get 4.66 kg weight for 1 kw power. The final flywheel or the 9th flywheel will have a speed reduction gearbox to match the input speed of the generator . The torus ring flywheel energy is in Joules 95235532087.5 or 26455 Kwh stored energy.
Once you findout how to produce torque n.m then these systems will start working! Kinetic energy from wheels only stores joules that can only make flywheels function like batteries! You will have some power but for short time! A very high effecient flywheel vacuum system with weight of 1ton and 20000-100000rpm can provide only for 24 hours of 2-3kw stored electricity!
Not 24 hours but 15-18hr in real world. Vaccum is good Idea but still it will make 18hr energy max. Then it will need generator to Again make it gain momentum.
the flywheel version of "keep your eye on the ball under these cups" game. You're not getting more out than you're putting in or the flywheel would stop. The draw on the generators eventually acts as a brake. kW in > kW out. cant beat thermodynamics.
You can put a bicycle instead of the motor, and start the flywheels manually... then it is totally free energy. Of course the bicycle should be electric to help you do the work.
Looks very fun. When you said this is not an energy storage i kinda didnt understand anything that followed. A bit like buying batteries that arent energy storage, i have trouble understanding the concept of whats going on lol. But would love to see one of those flywheels in a vacume levitating on magnets :)
Some tips. Hope you will not yell to my comment like you do to others. Learn how other youtubers make video, they may be not innovative or highly educated with PHd like you but they can talk and present. (Use a mic to record audio, prepare script) Learn some editing skills or hire someone to do a job. Your product looks old and cheap, next time paint it or polish remove rust from metal before presenting.(make a better first impression) I don't care it works or not but if you follow above at least your video will look interesting. Engineering tips: (I am an electrical engineer) Lifetime of your bearings. (I guess very short) Tip:Learn bearings used in turbocharger. (Turbochargers spin over 10k -20k rpm) All I can figure out is you are trying hard to store convert electricity into mechanical kinetic energy. Then mechanical energy to electric power. Ultimately the machine will come to zero rpm because you cannot generate more energy than you store. (Kinetic energy) There are mechanical losses in friction. Electric generator is also not 100% efficient. (Don't get angry it's truth) How to do a proper test to test your theory? Simple "resistive" Load testing (check and learn how power generators are tested with resistance load) Make a log, with load varying from 10% load (of total rated output) to 110% (Some companies test until 120%)
Oh my god. I can't believe that so many people take this movie seriously. Education in the world is still very low, if people believe in magic. Please: there is never a free energy and it will never be a free energy.
Daniel kowalski......dont be so quick to say never. Energy is everywhere, it cannot be created, it is just there, when it is released as in an explosion, where it burns your skin with the suns Ray's from the wavelength In the light from the nuclear fusion of the hydrogen in the sun. Its everywhere just a matter of capturing it and flowing it. There are too many people making these machines on a small scale and they ate not saying they are not working. Think about where the electricity from a gasoline powered generator comes from and keep thinking and you will have your answer.
Good effort, but without theoretical study. I'm not interested in rpm and torques. I want to know one thing, if I am giving 1 kWh electricity into your machine, whether it will give back 2 kWh for my use? These things need to be measured . 1. Energy given to fly wheel( measure the kWhr or units of electricity supplied). 2. Measure the output. ( Connect your generator output to energy meter and measure kWhr or units of elect.). If second one is greater than first one, pls let me know, I want to install one in my factory.
This is very old technology using the pendulum effect through flywheel, Russians already developed 10 kVA generator which can be install in drawing room! But I will appreciate your efforts too you!
In this video you discuss about gear box. Why we need gear box. You future plans to pose drive motor and flywheel and alternator will be in straight a line for more efficiency. It's good idea. I am planning to make one green power generator like this for my home load.
do not be confused by flywheel size and wieght . the flywheel stores input power example a flywheel connected to a motor via V belt same pulley size on motor and flywheel shafts let's say motor has 1hp output mechanical power (all ideal conditions no friction and air dynamic losses...) the flywheel will store this 1hp input power by its rotational speed the time taken while the flywheel is taking thiis 1hp is the energy stored in the flywheel. it means if u put a load on this flywheel say a generator 5hp and we put a 5 HP electrical load on the generator thy flywheel will give all it's stored energy to the generator reducing the flywheel speed 5 times faster more than it's inertial energy stored so it will go to complete stop very quickly . in normal conditions this happens much faster due to friction losses in bearings ,air hitting the flywheel , vibration losses (flywheel wieght not alligned ; shafts not 100% balanced and losessin the motor itself . so to get this straigh there is no such free energy except generated by sollar panels or a turbine feed by high pressure water from a dam .
Can you see the electrons coming out of the plug in the wall ? we are living in a world of energy he's not building electrons or energy just capturing work in a way which is useful . you also need to realize that there is a huge amount of energy in the natural environment even at 0 degrees there is still 240 odd degrees to you get to 0 calvin . There was a guy years ago made the worlds most efficient heat pump using gases that boiled at -50 odd F so he was able to produce steam to drive turbine even if outside temps were low , he got sent to jail for literally no reason
This might sound crazy but if you stand this on its head so that the fly wheels are horizontal they will be easier to start rotating they will still produce the maximum stored kinetic energy but because they’re sideways the weight is distributed more evenly try it and you will find out this is true
x / r = 2(c-v) x (rn*c-(2cv)/sqrt of (n-3.14159) - (c2*2(r/v) / r(t-r + c/v) * 2(n-t) + (csqrt - 2(n-v). That was more simple than I thought. I'm glad I thunk it.
Eu queria saber o que significa estas fórmulas de física matemática. Para eu entender a ideia do senhor eu primeiro tenho que intender as suas fórmulas de física matemática, a única formula que eu entendo, é as fórmulas do cursinho do segundo grau que é Ec= M × V2 ÷ 2 = E =M × V2 =
Any further development/break through in these six years? If one can get more output than input, this technique can be beneficially utilised for power production, is it not? Less pollution. More green.
Mr. Chaganti, Instead of arguing with everyone ehy don't you post such video which will clarify every thing in detail .As you say that 13 KVA will be available for two hours.....then post the video of two hours where whole world will see how you have produced free energy of 13 kva for two hours put that much load physically ( not show it on current meters or Volts meters.
It hasn't got ANY chance of running that long under that load. Did you see the enormous generator taking up the full bed of a fairly large truck parked 50 feet down that driveway needed to gradually bring those flywheels up to speed too.
i am not saying that i belive this man.... but just think about it why did he bother his time and waste his money making this giant Flywheel generator thing??? maybe its working and maybe its not. dont bash anyone if u didnt test it yourself yet... if it doasnt work so this guy is bullshit but what if it really work? u all will swallow ur shit bash.
That's what we heard about physics... But we should try because there are energies like vibrations, resonance, centrifuge, Gravity Acceleration we should know better.
The argument is: The large flywheel consume more energy than the Smaller flywheel causes the Generator to output: Although the input power will be less than the output power, the step-down physical layout is where the losses are occurring.
Sir cant you use the flywheel directly to a steam generator where it can substitute the turbine and there by reducing the friction and loss of energy from the turbines. Please others correct me if I'm wrong.
Fascinating concept, have you thought of using toothed drive belts that will not require as much tension so cutting down on the friction required for "V" belts.
congrats for your success sir , from 675 kw motor 1mw power is genrated . when 675kw motor (inductive load) is on and off frequently what about stability of grid
czcams.com/video/Enylbg2tlY4/video.html , Flywheel power Multiplication is the ultimate in clean and green energy generation regards Chaganti 8555045244
Dear brother,idont know what you are thinking about Pakistan, please don't compare my India to any other country in the world, because the extreme level of wealth and the technology is stolen from India and spreaded the rest of the world
Hi This is a design Exaggerated I have a tip for you These giant iron circles I have a small idea 1 iron circle put in it DC The second iron is a circle, put in it volt generation wires Thus, the obstetric automatic My greetings
Sir...please make it available for all countries....poor people pay millions for electric power....spread it in your lifetime.... make it Available at once in global scale....then only it will come to india...Thank you.
Correct me if I am wrong, the flywheel is like an energy storing device like a battery. So let us consider the same setup that you used wherein you use a motor to rotate the flywheel. In simple words you are transferring the mechanical energy of the motor to kinetic energy of the flywheel. Now after the flywheel or "battery" has reached to its full kinetic energy or "charge" by the motor or the "charger", you are turning off the motor or "charger" and therefore the flywheel continues to spin due to moment of inertia therefore dispensing its stored kinetic energy or "charge". At this particular instant, the input to the entire setup is 0 watts but the output by the generator is say whatever the capacity of the alternator/PMG is. So, my question is this power multiplication? Because to me it sounds like you're storing energy and using that same energy. I would rather call it much worse because here we would have to consider much more inefficiencies like the motor will have some losses, switching losses of VFD, frictional losses by the bearing, static losses by flywheel. So, what energy you dispense by the motor, which then is stored by the flywheel and then is fed to the alternator/PMG, there is a drop in energy at each stage due to these losses. Now, let us climb another step further wherein you mentioned the smaller motor is running. Imagine that the system is fully charged (meaning flywheel is rotated to its rated capacity) and now the alternator is in mesh with the flywheel and there is an instantaneous full load connected to the alternator/PMG. In this case there has to be an obvious drop in speed (RPM) of the flywheel. Now as suggested the lower capacity motor will run and make up the "RPM's" lost. Now won't the smaller capacity motor need to dispense an equal amount of energy to "charge" this flywheel bank? Or rather we can sum it up like the higher capacity motor is a "fast charger" and the lower capacity motor is a "slow charger"? Now to take it another step further the losses of the smaller capacity motor is to be also considered. Also, not to mention that your alternator/PMG is always meshed, needless to say, even they have losses to be considered. In my opinion I would rather call this an uninterruptible power supply, where you charge a battery and use it when the power goes or there is a low voltage! So, my conclusion on this is that flywheels are to be used to avoid "jerks" in the supply system and not to multiply or generate power.
😂😂 exactly it's just onether misunderstanding of simple energy conversion.. fly wheel is just a power storage device.. there were even vehicles in the 1940s that used it but it was so inefficient.. he could just call it power divider instead of multiplication
I think I'll make one and call it a mechanical smoothing capacitor!!! 😮😅😂😂
Quero ver em portugues
Your talking is very exaggerated about the losses !!, ( The bearing losses are also very small ) There are also no (frictional losses) except with air(still small), but there are losses due to magnetic fields and Eddy currents ! generally, The motor/generator is known for its high efficiency.
yes, the Flywheel consider as power multiplication because it gives more energy than you put into it !
@@onesmuskabangi2444 On the contrary!, it is very effective, especially at that time. Now this technology can advance further.
This is NOT AN ENERGY MULTIPLICATION POWER SYSTEM but can be thought of as an ENERGY STORAGE SYSTEM. To be more specific, we can use this system to trap or hold the mechanical energy using fly wheels of minimum rotational friction (of-course with an exponentially but slowly decaying fashion) for some time.
Can be a very good energy storage system (may be comparable to batteries) to hold the power generated during day time when using solar power panels. This system can slowly release the energy to a connected load during night.
To store that much enery in a flywheel to use at night the flywheel would need to weigh hundreds of tons
czcams.com/video/ujNeP_iASZs/video.html
@@harrytopia282 Yes, huge flywheels on gigantic metal stamping presses will coast to a stop in a few minutes after the power is shut off and they are even running without a load on them.
Or a smaller flywheel that could run about 100k rpm or more
@@harrytopia282 I agree with you . Arrest deceivers off CZcams pronto before more young minds are destroyed and their wallets and wasted time. There is no free lunch in the universe.
Ma Sha Allah, This is an excellent design and concept. Congratulation to all of you.
This particular explanation of this particular flywheel is particularly hypnotizing to listen to.
😂😂 why he always says ''particular '''
if this particular flywheel veers off that particular rack at 6k RPM half of the particular village will be gone 😂
I just enjoyed the way this man flows in his explanation. Kudos
this is actually really impressive. Those bearings are a very good engineering design choice same with the flywheels. Pulley and shaft shape could be changed for a more efficient energy transfer. Great job
The "efficiency" of transfer means nothing. How much friction in the bearing is the only real consideration in the transfer.
Belt or chain drive are particularly low friction.
This certainly is a great example of energy storage, but not “free energy”. One thing I did not hear you comment on is mechanical losses. There is friction here... there has to be. This machine is also extremely dangerous. How it was balanced would appear to be pretty scary. That welded plate on the wheel is representative of an effort... but...
you are right sir
Es gratis. Ves algún motor a explosión ?
After your success my selute to you sir getting patient is your biggest achievement. Now it's our government's responsibility to bring this technology to everybody's life. 👍
Multiply Input voltage with current to calculate input power. then use the same way to calculate output power. Now you have to consider the time. I mean calculate the Watt hour. compare Input watt hour with output watt hour, then you will see output watt(load) is decrease as stored energy in the fly wheel is finishing. Which makes you understand that it is not possible to generate more power than input.
You should start studying both mechanical and electrical engineering.
this man is equally passionate as he is ignorant, he does not bother to read comments..he is a stupid man with equally irritating looks.
Sir, A megga FlyWheel the main source of power to drive the Generator.Great job.I salute you. Philippines
1 नंबर गति के सिद्धांत को आपने सही रूप में ढाला है कुछ अलग कर दिखाने का जस्बा ही इंसान को दूसरे से अलग बनाता है प्राउड u प्राउड इंडिया
my india my proud 7
dumb gawar pad h le ye fake video hai
Waah chutiyee🤣🤣
8000lb flywheel at 3000 rpm?
I don't know what this guy's trying to do but I love it
That's a GREAT idea:
1) store some energy in mechanical form
2) recover it during a demo showing off whopping numbers.
3) pocket the money from inedicucated investors.
PURE GENIUS!
So if I understand this right, the energy to maintain the rotation of the flywheels is less than the energy that can be used to generate power. Your energy loss is condensed to the initial start up of the flywheels, which is significant, but once the flywheels are in motion your input is less than the output. This is still an energy storage device in practicality, but that in itself is very valuable. Imagine scaling to the 100 ton flywheel size, and using mechanical wind power through a variable gearbox to increase the RPM of the flywheels during peak wind. Then you could draw electricity from a series of generators when needed at a variety of voltages at what ever amps needed at the time. Even excess Photo-voltaic energy could be used to increase the rpm during peak sunlight periods . With these two energy sources producing the power to generate the RPM the generators would slowly reduce the RPM when producing electricity on demand. There is not a total energy multiplication, once you take in the start up energy needed, but it is an excellent way to store the energy from wind and solar, both of which are variable. Keep up the good work
You got this completely wrong. He is claiming free energy. That is bullshit.
@CNC Basic If you understand vector and scalar forces. Gravity is a vector force. You know what it means? Certainly no. When you refer to energy you are talking about a scalar force.
@CNC Basic No Sir. Gravity don't run your heart but Gravity is needed for life to happen.
@CNC Basic Gravity is electromagnetic force? Which university bro ?
@CNC Basic You skipped Biology classes as well? If yes do some research in Internet. Have you heard about motor nerve3, spinal cord, Nerve cells and Brain. I don't want to Physics and Biology classes. You stay in your ignorance. Good for you.
Energy in = less energy out (loss due to friction etc). The form of energy does not matter. So there is no power multiplication. Though energy storing in an 8 ton flywheel is a good idea. You can rotate the flywheel (when the bearing is ok) by hand or a few Watts source, you don't need 20 Kilowatt to make it spin. So that does not tell something about efficiency. Input amp = 15 A and output Amp is 28 A, that also does not tell anything about efficiency and input power versus output power. Watt = Electrical Power = Volt x Ampère (DC situation). Anyway: a good idea to store energy this way.
yes, same thinking.. he is saying that we are having more enery out than input, 15A in 28A out, but he is missing that what he is getting out he stored that energy in the system at the beganing. i think he is engineer but i just can't understand how he missed that.
but as u said it is ok to store the energy, like a bigg capacitor in electronics
When I was at School in the 90's I asked my Physics teacher about this concept, I was reminded of the laws of conservation, and the class carried on.
I knew it was a good idea! Scaled up, with gearing, this concept will rock!
You had a good teacher. This man needs that teacher, or may be he just wants to make money off youtube algorithms
Und so ist es
Who made the law of conservation??
Human or God??
Who can make law??
If God make the law I will accept.
If human made the law - I will say that is cheating.., because of fuel Market.
I
@@anbarasanstalin5998 the law of conservation of energy is not a legal law, its simply a description of reality. Energy can be converted from one form to another, but never lost or created out of nothing.
Its just how shit works.
@@anbarasanstalin5998 This guy @brahm-ahamasmi should change his name to Scientist-o-Asmi.... These people desecrate Hinduism by keeping such names....
I am a Industrial Electrician and have been for 45 years and am highly experienced with large electric motors , generators , alternators and especially Variable Speed Drives (VSD) .
Now ...... The only energy input into this "machine" I can see is the large 3 phase motor (light green) which is supplied thru the large VSD in the building which allows them to control the speed of the whole system . Huge concern !!!! I see no earthing or machinery bonding what so ever . Very disturbing . No true electrician was involved in hooking up this debacle.
He is claiming that more energy can be derived from the assembly than is inserted from the large motor . NO! I estimate with the Vbelts , the very large bearings , even the motor and "Generator" bearings plus the wind resistance on the flywheels at least 15 to 20% of the energy (electric power going in) is consumed by these alone . It looks like he is claiming that when he revs up the flywheel with large motor , then turns that off and "runs" the system then with the little motor (never saw that) then he can connect the generators and pull free energy out of the system , NO NO NO NO he can't , and I suspect as the flywheels run down ,as they will, he has connected a generator to the flywheel and its output to the "small electric motor and thinks that will keep the system running (it won't) ..
If he believes that and he seems to have convinced a whole lot of people of such a miracle including the Telengana state government by inviting him to exhibit his invention on independence day celebration, he is either one of 2 things .
Extremely naive and dare I say "stupid" certainly not an engineer or he is a con man !
This is an energy storage device yes , very inefficient but yes !
But it is not and there is no such thing as a power multiplying device that can subtract energy out of nowhere and utilise it . There is a lot of power stored in the flywheels especially at 6000rpm (i wouldn't stand near it !) but that power /energy comes from the large electric motor initially and no where else . Throughout the whole universe the equation is :
power in = power out minus loses (friction) .
In that equation is the death of all perpetual motion machines !
You are absolutely right sir.
He is a fool.. Making others also fools...
i'm agree with you sir.
@@bourseiran7935.I am stealing electric power =free power.
all you say is theory and blah blah ...
in all neutrality, if you think it is a scam then prove it, as he does by experience or otherwise you shut up. thank you
i need umbrela.. its raining "PARTICULAR"..😂😂😂😂 any ways it is good invention.. salute to u particular scientis..😅😅😅
To fir itchguard laga lo.
Yes, it is raining bullshit, along with the thousands of other free energy scams on YT this one is just as ridiculous as the rest just more elaborate.
Sir,I tried this experiment,it didnt work,then I asked one scientist,he told me,we can never generate electricity ,with electric motor and dynamo interconnected,the forces will cancel eachother and become zero,this is because the more the electricity , motor draws ,the Tighter the dynamo armature becomes,and slows down the motor, and finally the motor comes to stop ,that is what that scientist told me.
But with the help of flywheel if you are able to make it successful ,then it is a good invention,very good sir,
keep it up.
What if we use electric generator to rotate a big flywheel in Vaccum. It will give enough momentum to generate electricity for 3-4hours enough for short powercuts.
What do u think??
గౌరవనియులు చాగంటి కొటెశ్వరావ్ గారు మిరూ చెసిన మిషెన్ చాలా బాగా నచ్చింది
క్షమించి నాకు ఒక మిషెన్ చెసి పంపిచగలరు
According to him
This whole system × 24= 2 day continues flow of current...
It Also enough rotate to power up the first one system ,
Can From the last one system....
He can also start a electric mill for whole hyderabad....
Iam positive about you good luck sir appreciate it
The higher out amps compared to input amps is one thing however, I am most interested in the "total" input energy vs total output energy using accurate and documented (recorded) measurements of all dissipated energies. I suspect that the stored energy in the flywheels presents the apparent 'free' energy gain. In effect you are likely just slowly running down the stored inertial energy of the flywheels. Thus you will only 'apparently' be able to generate 'free' energy for a constrained time period. This can be proven another way and that is by maintaining the angular velocity of the flywheels under heavy load and taking measurements under that condition.
D
You always put more energy in this thing then there will come out.
28kevin28
A pendulam gives twice the energy that is input. This is not magic. The angular momentum of the rotating earth is transferring energy through gravitational force field. The fly wheel works similar to a pendulam.
Vee Gee tell me how a pendulum gives out double the energy to start it lol. I think you need to revise mechanics.
You are talking nonsense.
Of course you can get MeggaWatts of free energy just from the air.
Only the electric lobby (and their corrupt governments) keeps us buying energy from their power plants. It is massive government conspiracy.
They even changed the physic books and are force teaching in schools some fake laws of energy conservation, it is all lies. Flywheel will give you as much free energy as anybody needs.
A hell lot of chutiyas on internet.
Twice the energy as if it is milk of a bitch😂🤣
This is the electrical equivalent of chopping a 2x4 block of wood in half and bragging that you've multiplied it into a 1x8. Having more current coming out than is going in is meaningless without a measurement of voltage at both sides, otherwise the high pressure nozzle on my garden hose is "multiplying" water because it comes out at high pressure.
he could have used high amp transformer instead.
🤣🤣the more water analogy was so spot on
I think he is using it for Momentum. Your 2x4 to 1x8block is like your saying it’s just as efficient for Amazon to deliver packages across states using small vans instead of Tractor Trailers.
It’s going to take the same effort? So why not use the smaller option?
Bull shit bakwas karha he jab loses HONGE to ye ni chal pae ga
@@MJ-ee7fr then that will slow down the flywheel so fast 😂✨
Interesting research! Keep up the good work. I'm sure in time you will improve the design close to perfection. In the meantime, I think I will stick to my LiFePO4 battery bank to store my access solar energy.
Mopuri Balu from puttaparthi.
Chaganti sir, l respect ur hardwork. you are not generating new power.you just are storing grid/battery power in flywheel for sometimes.
Please call 8555045244
8555045244
6000 RPM on plummer blocks of that size with Grease lubrication "Frying Tonight" a most likely outcome.
2 houres garantie....
3.9 M views......they got what they need.....well done... continue these type of videos and fool the world..
Hat's off... Sir you are solving a major problem of the planet
I built exactly the same machine. The only problem is that I supllied 220Volt but it gives me 230 Ampers. So, from my calculations: 230A - 220V = 10 Watts of free power. When I divide it by 5 buckets of goat milk, I receive 1.5 pounds of square inch of energy per mile and that is a huge gain, even NASA has no such results. Correct me if I am wrong.
A cordless 10v drill can turn that wheel🤨
if that gentleman is bearly touching it and he makes it turn..
running a drill / small motor through a simple bicycle drive train would crack a few hundred rpm..while putting out + mega watt of axle torque you use to turn a HUGE flywheel..then take from the axle....stacking flywheels is like lever stacking....3 see - saw levers are pretty much the max...but wheels can have gear boxes....from 1 bike 1 man could probably slowly turn the London eye wheel after 4 or 5 increasingly bigger flywheels stacked..
I need 1 megawatts .help
Flywheels are used as a cheap and easy way of storing rotational power. The greater the diameter and mass, the longer it will rotate after power is no longer applied to the system. The flywheel will eventually stop rotating. I'm not sure if the presenter properly explained this.
I think he will run it with low hp motor, high hp motor is for starter.that's how he cut the input voltage.
Da B.S. is flowing, boy it’s getting deep!
Congratulations for using the word "particular" more times than I have used it in the last 40 years!
What is new or special here? Off the shelf components (geni and motor) which all have specific losses in doing their work. (Eddy current , copper losses, etc.) Given you are throwing away this energy as you try to spin up the big flywheel you can never get it back. This system is good for an uninterruptible power supply that can keep supplying a continuous waveform during a short interruption of mains power while there is a switchover to battery power to spin the flywheel/generator until the utility power is restored. We had this technology where I work for years since the 1980s and that flywheel powered device which provided our sensitive technical environment with constant power was called a PILLAR system ( German Technology I think) and it used the flywheel effect to overcome losses in mains power for milliseconds while batteries took over in keeping the flywheel spinning at synchronous speed..There is no free power here and what needs to be calculated is the efficiency which is always less than 100% = 1.
This flywheel system was in use to get uninterruptible AC power supply in telecommunication system. The flywheel keep the driving shaft rotating during switch over from motor to generator through a magnetic clutch. (Old system)
I have designed an active steering wheel that once accelerated cannot stop its march, it is much lighter than that common steering wheel shown in the Video ... / I have combined the absolute movement, with the relative movement, the Potential of the gravitational force with mechanical energy The machine is universally applicable and infinite useful possibilities // Yo he diseñado un volante activo que una vez acelerado no puede detener su marcha, es mucho más liviano que ése volante común mostrado en el Vídeo... / He combinado el movimiento absoluto, con el movimiento relativo, el Potencial de la fuerza gravitacional con la energía mecánica La máquina es de aplicación universal y posibilidades útiles infinitas
So basically he is saying that he defied basic law of conservation of energy? Come on "free energy" is just a scam. Secondly ampere comparison is not accurate thing to do. Ampere has no significance without voltage.
If he is true that output amps are higher than input amps, input voltage must also be higher so there's no free energy generated.
I was studying this system and in my case, I was astonished until I tried to grasp the whole thing.
Then , here it goes the explanation for the analyzed system :
Electric Generator (let's say 5 Kw @ 3650 r.p.m rated power) power is generated from a Motor which only provides ( let's say 3 Kw @ 1725 rated power) . At first glance it seems as if the system where generating (5-3 = 2 Kw) . However we must be aware that High Inertia Values from Flywheels impossed high loads to the motor . The motor tries to achive this exigent load varying its working point , reducing its rated angular velocity (increasing motor slip , decreasing for instance to 1600 r.p.m ) and when this happens , the current and obviously power comsumption will be increased to respond this higher than rated load. Depending on the motor kind this new working current could be as high as 5 times the rated current , so , It's normal that power consumption could be twice or three times the rated power for the motor . I stronly recommend you guys to watch an induction motor torque power curve.
In conclusion , Motor really demands 6 Kw ( 2(double in demanding power ) * 3 (rated motor power )) . With this established , it is clear that we have not broken 1st thermodynamics rule :
(Motor power = 6 KW ) = (Genarator power = 5 KW ) + (loses = 1 KW)
As you probably know this 1 KW lose energy must include:
*Friction with air.
*Noise levels.
*Mechanical transmission loses .... etc .
Pd.
It was really curious that in the video He measured Voltage and Current , but , unfornately he didn't measure the output voltage in the generator ... he did measured only the output current....
Looking forward to hearing some replies
In other words its, super high efficiency using the flywheel to scalp off exrtra energy that normally would be lost or unused How efficienct do you think it is...60 ..70...80...90...95.%?.cause that's a big ass fly wheel ....wouldn't want to be any where near that when the bearing fails.
@@gta-6837 🤣🤣
Lol he is using 8ton disc flywheel. Idiot could have rim type.
Excellent concept sir. I do have an a concept but some what it risky. but u r good and i wish u all the best for your future implementation
आज से छ साल पहले जनवरी 2014 में यही आइडिया मैंने कुएं पर डीजल जनरेटर को चलते हुए देख कर दिया तो सब लोगो ने मेरी हंसी उड़ाई थी ।
आज इस वीडियो की लिंक सेंड करके बताऊंगा की में सच था ।।
मुझे आज अपने आप पर गर्व हो रहा है 💪💪।।
Energy can neither created nor destroyed but can be transformed from one form to another - Law of conservation of energy
All wronge energy is being created do the foot work finde out
We like the electric motors. Greetings from Germany.
6000 rpm on plummer blocks, I dought it I know of some car engines that don't rev that high. At first those flywheels looked as though they were only doing a couple a hundred rims. Those plumber blocks would overheat at 6 grand and fry the lube and then the bearings size and then the whole gizmo would just fly to bits with desasterous results, maybe 600 rpm is more likely and those big flywheels would have to be precisionly balanced otherwise any imbalance would shake the whole contraption to bits and I don't think I would like be near that thing when it's spinning at 6000 rpm and one of those flywheels decides to seperate and break free from that thing.
Where were you educated?
@@Lesdig891: " Where were you educated? "
Why were you NOT educated? His points are spot on. If you're stupid enough to believe ANY of these free energy liars you deserve to waste money trying to replicate their garbage since you're obviously too stupid to understand there is no free energy from ANY of these stupid (and in this case and many others) dangerous contraptions.
@@lorditsprobingtime6668 chill out asshole hahaha it was a simple question I didn't dispute his points I was just wondering if he had a degree in mechanical engineering or something
@@Lesdig891 Your insinuation was that he's not qualified to have the opinion he has a hole. Now you're lying about your intent to 'try' and sound slightly more reasonable, you're just an idiot who wants to try and sound superior, screw you.
@@lorditsprobingtime6668 these people aren't building things and wasting their time and money because it doesn't work! These things work!! People generate power for their homes for free! I've seen many people build these types of things, they work!
This particular flywheel will keep accelerating, reaching 99% of the speed of light. Generating more energy than all the combined stars, black holes, aliens, pulsars, in the universe .
Once it reaches 88mph it will take you back to 1985.
It’s essential to building a time machine since there’s no gasoline and electricity in the ancient past like whenever that WW II thing happened. Come on man! You know what I mean!
When this machine inaugurated and launched Iron Man and Spider Man will be there so that they can save our human life from extreme energy generation by this machine.
Wow! Gee whizz!!
Right boss. 😂.
Flywheel energy storage systems using mechanical bearings can lose 20% to 50% of their energy in two hours. Much of the friction responsible for this energy loss results from the flywheel changing orientation due to the rotation of the earth (an effect similar to that shown by a Foucault pendulum). This change in orientation is resisted by the gyroscopic forces exerted by the flywheel's angular momentum, thus exerting a force against the mechanical bearings. This force increases friction. This can be avoided by aligning the flywheel's axis of rotation parallel to that of the earth's axis of rotation.
Conversely, flywheels with magnetic bearings and high vacuum can maintain 97% mechanical efficiency, and 85% round trip efficiency. #Wikipedia#
Flywheel energy storage has been used in public transport and even in mining vehicles. There is nothing nonsense in this contraption (well you have to turn volume to zero), only very low efficiency.
This is fascinating. I wonder if this concept can be modified to incorporate snowmobile-style CVT (Continuously Variable Transmission) Primary and Secondary clutches? Though the gearing changes are technically infinite, in reality, it's comparable to having, say, a 3-speed bicycle except no jarring gear changes are needed. I do believe the snowmobile belt design is superior to the standard V-belts used here as well, though finding them in the correct length needed for this application could be quite problematic. Of question would be if the benefits would overcome the increased complexity and friction due to more moving parts.
All of the stuff in this comment is true, although storing energy in flywheels is not the subject of the video.
The video essentially claims that the efficiency is over 100% and is therefore creating energy.
Energy storage in flywheels is ordinary, and is all that is happening in this video. Not only is no additional energy generated, energy is lost due to the forces discussed in the above comment.
You can’t create infinite energy with flywheels, no matter how much you hope and dream about it.
@@benpatchett5427 I like your comment Ben. What do you do or how do you know about this subject if I may ask?
@@GangsterBusiness flywheel vehicles are not new, I think in England , a flywheel based tram system was developed (I don’t remember the name of the town), but this was discontinued as it’s not a efficient system
Earth rotation assuming it exist, doesn't affect airplanes on flight why would it affect this wheel?
idiots luffing about "particular" others impressed by this free Technics
thanks !
Good Job Sir ! This American Salutes your Skills ! I am subscribing to your channel so I can see how you Engineer & Correct
The Negative's !! ( Trial & Error ) is how we make things better !!
czcams.com/video/G67-y1axDJQ/video.html
So basically he is saying that he defied basic law of conservation of energy? Come on "free energy" is just a scam. Secondly ampere comparison is not accurate thing to do. Ampere has no significance without voltage.
If he is true that output amps are higher than input amps, input voltage must also be higher so there's no free energy generated.
@@green_life7 even they got patent!
@@sridharsridharthota1077 there are thugs everywhere and loopholes in the process too.
@@sridharsridharthota1077 no they don't have a patent. Its Its only a provisional application.
Alhamdulillah saya waktu sekitar 2004 udah faham betul dengan teori ini hanya saja belum pernah praktek karena ga ada support.
Malah pernah beberapa kali konsep atau gambar skema nya saya upload atau posting kala itu di Yahoo grup atau yahoo mailing list namun karena waktu itu sangat awam jadi ga pandai dokumentasi jadi ga banyak data yang dapat disampaikan saat ini.
Waktu itu konsepnya PLTL Pembangkit Listrik Tenaga Listrik.
Dinamo 200 watt (nyala awal pakai pln) gerakan 20.000 watt menggunakan dobel piringan besi atau baru baru ini saya baru tau kalo namanya sebutan nya playwheel gitu.
Kalo waktu itu saya sebut dengan teori momentum sebagai penggerak utama nya.
Mudah mudahan dalam waktu dekat bisa segera membuatnya dan dapat bermanfaat bagi masyarakat
Thank you Mr Changati and team. I am appreciative for this knowledge. Your work is very impressive indeed. As i child, when playing with small motors from toy cars, to my surprise i realized that when rotated, the motors lit small bulbs. The question is, is it possible to build durable units that can be connected and used domestically??? Am interested in doing this
Oui c'est possible
So basically he is saying that he defied basic law of conservation of energy? Come on "free energy" is just a scam. Secondly ampere comparison is not accurate thing to do. Ampere has no significance without voltage.
If he is true that output amps are higher than input amps, input voltage must also be higher so there's no free energy generated.
No one can generate energy Moses. 'Energy can neither be generated nor destroyed' is a fundamental law of thermodynamics.
@@ndreddy8416 Hmm...but can be converted from one from to another. To Generate energy is the same accumulation of energy. What you probably meant was that energy can’t be created. The question is, how can this be achieved as cheaply and as efficiently as possible? I see a solar charging system somewhere. A unit or setup a peasant can run domestically. However much I ponder this, it seems to come down to cheap and yet efficient energy storage cells.
Thanks for such hard work, but two questions; 1, if your input is 20 KW, then how much is the output (sure, it should be more than output) and 2, when we use about maximum output of system, does the input machine support it? as I experienced it, it doesn't and gets slowly stopped..
1kw rein im System und 15 kW rauskomme
سر بہترین چیز بنائی ہے دیکھنے سے پتہ چلتا ہے لیکن تمام بات جو آپ نے کی وہ اردو میں بتائیں
No must two whell just one
یہ ساؤتھ انڈیا کے واسی ہے یہ اردو پر قدرت نہیں رکھتے
Very Good Bhaskar
If you were here in Brazil, a project like this in the industries here in my region you would sell quietly, very good.
How many KWA does this plant produce?
Enough to power the enterprise.
Less Kw out than you put in to spin up the flywheels........there is no free energy..!!
I built a device once that had several disks all larger than the next. I think I had 10 in all. The smallest 4 inches and the largest 4 feet in diameter. Each disk had aluminum plates on the outer edge side facing the next larger disk. Each disk had magnets on the side facing the smaller disk place in the diameter of the next smaller disk. All except 2 of the disks were on a shaft with bearings that would turn independently of each other except for the largest disk was attached to the shaft. The very smallest disk was attached to a 9 volt motor about the diameter of a quarter. I would turn on the motor and it would spin. This would start the bigger second disk spinning and the second d would start the bigger third and so on. I was able to spin the 4 foot disk at about 135 rpm in the end. You could slow the largest disk with a load and have very little affect on the smaller disks. I have torn it apart and the rennets are still in my basement. I would love to see this built to low tolerance specs. Maybe even use copper plates or coils instead of aluminum plates.
Mine was cut out on a table saw from 3/4 project board and some parts made on my cnc router to hold bearings and such.
भाई साहब हो सकता हे पर धीरे मेगेटज़्म वीक होता चल जायेगा
hello I really appreciate your engineering design and you have explained your design extremely well and I'm feeling like I didn't get the generator output but I do observe your amp output and input please provide me the KW / Volts so that I can know this much better way
So basically he is saying that he defied basic law of conservation of energy? Come on "free energy" is just a scam. Secondly ampere comparison is not accurate thing to do. Ampere has no significance without voltage.
If he is true that output amps are higher than input amps, input voltage must also be higher so there's no free energy generated.
@@green_life7 So true👍
You are right..the amps have been increased but the voltage was probably decreased…kw will remain same if not reduced because of friction losses
Will you please clear what is input and output.
Absolutely 💯 correct if thye not doing scam tell us the input voltage and amps output volts and amps or input wattage and output wattage
ఇది నూటికి నూరు శాతం నిజమైతే ప్రపంచమంతా మీ కాళ్ల దగ్గర ఉంటుంది
ఇప్పుడున్న ఫిజిక్స్ శాస్త్రానికి అతీతంగా ఉంది
Those are some big flywheels!
Dear people, since electricity is supplied to remote villages with thin wires, it becomes impossible to use devices with a high peak load, this device was created for this. At the time of using high power, the shortage is covered from the energy that is stored in the flywheel.
After this particular invention, based on the pure science of miracle, India already closed all power plants. This flywheel alone, supplies enough free and green power to whole country. I just returned from travel to India and I did not see any power plants there, all generating plants have been closed and demolished, due to this particular free invention. All villages and cities have only flywheels produced by Mr. Chiaganti.
Energy can neither be created nor be destroyed. Have you tested after connecting electrical load to the generator?
And I thought the India-based phone scammers were bad. Apparently, scamming is endemic there.
Energy can neither be created or destroyed. It's converted from one form to other. Current production is having a load of magnetic flux cut by coil. This action needs force. The stored energy in flywheel would get stopped when a good amount of electricity is produced in demand. Here load is lower than a certain limit which allows flywheel to roll.
you might be generating 20Amp from 15Amp input but what is the input & Output power ? I am sure the voltage will be less in output.
May be this particular video is helping the particular people today to Research on this particular way of generating the free particular Electricity, and the video had used the word "particular" in such a particular way, but I'm shocked that nobody on this entire planet noticed the word "particular" in this particular video.
I appreciate your particular idea.
You’re just way to particular !!!
Appears these fellas are destroying the laws of thermodynamcs ; )
It would be interesting to find out what increased efficiency could be experienced by adding mag lift components, which should eliminate some drag from the particular friction on bearings, etc. I find this kind of innovation very exciting.
If you add more, metal plate start to bend.
Dear sir, in our workshop we achieved this with 2 meter in diameter and 4 tons in weight 100 kw is the storage of the flywheel. If the flywheel is 8 tons in weight minimum 3 meters and maximum 4.5 meters in diameter and rotated at 7000 rpm then the total weight required for generating 1.6 MW will be 70 tons . If each individual flywheel is 8 tons in weight and there will be 9 flywheels in total. Each wheel is attached with the other and one independent gearbox is fixed with the first flywheel and rotated by a 15000 kw Motor (Dual speed or 2 speed motor) there by all 9 wheels are rotated at 7000 rpm each wheel multiplied with 9 independent wheels there by total rpm will be 63000 rotations and the cumulative flywheels total torque is transferred to the 1.6 MW PMG generator with 750 rpm there by if we convert the rpm into (RPS rotations per seconds ) then the rps of the flywheels 1050 rotations and the PMG wil be 12.5 rotations per second. The torque of the generator is 20370.77 NM and the torque of the 15000 kw motor is 47744.00 NM. The 9 flywheels will keep on rotating for more than 3600 seconds and Free energy is generated. In put is just 10 seconds time for the 15000 kw dual speed motor to rotate 70 tons to 7000 rpm and leave it to rotate by itself on the plummer block bearings . Here if the 70000 kg weight is divided by 15000 kw power then we will get 4.66 kg weight for 1 kw power. The final flywheel or the 9th flywheel will have a speed reduction gearbox to match the input speed of the generator . The torus ring flywheel energy is in Joules 95235532087.5 or 26455 Kwh stored energy.
was thinking on same model from so long days decade of weeks , good to see this presentation
Ma Sha Allah, This is an excellent design and concept. Congratulation to all of you. best of luck
Once you findout how to produce torque n.m then these systems will start working! Kinetic energy from wheels only stores joules that can only make flywheels function like batteries! You will have some power but for short time! A very high effecient flywheel vacuum system with weight of 1ton and 20000-100000rpm can provide only for 24 hours of 2-3kw stored electricity!
Not 24 hours but 15-18hr in real world.
Vaccum is good Idea but still it will make 18hr energy max. Then it will need generator to Again make it gain momentum.
कृप्या इस विडीयो को हिंदी में डब कीजिए ताकी हम हिंदी मिडीयम वाले भी समझ सके ।
nahi samjo to achha hai kuch kaam ka nihi
the flywheel version of "keep your eye on the ball under these cups" game.
You're not getting more out than you're putting in or the flywheel would stop. The draw on the generators eventually acts as a brake.
kW in > kW out. cant beat thermodynamics.
Absolutely correct.
Ну вот, прорвало ЗАПРЕТНЫЕ ТЕХНОЛОГИИ...
Не удержать !
he could scale this up and rule the universe.
You can put a bicycle instead of the motor, and start the flywheels manually... then it is totally free energy.
Of course the bicycle should be electric to help you do the work.
lol good one
Looks very fun. When you said this is not an energy storage i kinda didnt understand anything that followed. A bit like buying batteries that arent energy storage, i have trouble understanding the concept of whats going on lol. But would love to see one of those flywheels in a vacume levitating on magnets :)
If a bearing broke on one of those flywheels at 6000 rpm, that damned wheel would crash through everything in it's path
Some tips. Hope you will not yell to my comment like you do to others.
Learn how other youtubers make video, they may be not innovative or highly educated with PHd like you but they can talk and present.
(Use a mic to record audio, prepare script)
Learn some editing skills or hire someone to do a job.
Your product looks old and cheap, next time paint it or polish remove rust from metal before presenting.(make a better first impression)
I don't care it works or not but if you follow above at least your video will look interesting.
Engineering tips: (I am an electrical engineer)
Lifetime of your bearings. (I guess very short)
Tip:Learn bearings used in turbocharger. (Turbochargers spin over 10k -20k rpm)
All I can figure out is you are trying hard to store convert electricity into mechanical kinetic energy.
Then mechanical energy to electric power.
Ultimately the machine will come to zero rpm because you cannot generate more energy than you store. (Kinetic energy)
There are mechanical losses in friction.
Electric generator is also not 100% efficient. (Don't get angry it's truth)
How to do a proper test to test your theory?
Simple "resistive" Load testing (check and learn how power generators are tested with resistance load)
Make a log, with load varying from 10% load (of total rated output) to 110%
(Some companies test until 120%)
Ski G Most turbos run on pressurised oil as a bearing.
Destian Light yep thanks for your input
Perfect answer....
)
Oh my god. I can't believe that so many people take this movie seriously. Education in the world is still very low, if people believe in magic.
Please: there is never a free energy and it will never be a free energy.
There is a good amount of energy which we can generate by 200% by a motor and a generator..
Daniel kowalski......dont be so quick to say never. Energy is everywhere, it cannot be created, it is just there, when it is released as in an explosion, where it burns your skin with the suns Ray's from the wavelength In the light from the nuclear fusion of the hydrogen in the sun. Its everywhere just a matter of capturing it and flowing it. There are too many people making these machines on a small scale and they ate not saying they are not working. Think about where the electricity from a gasoline powered generator comes from and keep thinking and you will have your answer.
Came here .you see a new Project. Brazil
Good effort, but without theoretical study. I'm not interested in rpm and torques. I want to know one thing, if I am giving 1 kWh electricity into your machine, whether it will give back 2 kWh for my use? These things need to be measured . 1. Energy given to fly wheel( measure the kWhr or units of electricity supplied). 2. Measure the output. ( Connect your generator output to energy meter and measure kWhr or units of elect.). If second one is greater than first one, pls let me know, I want to install one in my factory.
Your constructing the machine
This is very old technology using the pendulum effect through flywheel, Russians already developed 10 kVA generator which can be install in drawing room!
But I will appreciate your efforts too you!
Can you contact by my email chrisokoye2010@gmqil.com I have built 5kv.some fine-tuning still required.
either remain please share also the Russian model
You are great if you are working on "free energy" but take care from the oil companies as they are killing all free energy people.
LearningZone good one
yes ......this is true.
The real design challenge for "free energy" machines is : how do I hide the input power wires?
Nailed it..😂😂😂
🤣🤣
In this video you discuss about gear box. Why we need gear box.
You future plans to pose drive motor and flywheel and alternator will be in straight a line for more efficiency. It's good idea.
I am planning to make one green power generator like this for my home load.
do not be confused by flywheel size and wieght .
the flywheel stores input power
example a flywheel connected to
a motor via V belt same pulley size on motor and flywheel shafts
let's say motor has 1hp output mechanical power
(all ideal conditions no friction and air dynamic losses...)
the flywheel will store this 1hp
input power by its rotational speed
the time taken while the flywheel is taking thiis 1hp is the energy stored in the flywheel.
it means if u put a load on this flywheel say a generator 5hp
and we put a 5 HP electrical load on
the generator thy flywheel will give all it's stored energy to the generator reducing the flywheel speed 5 times faster more than it's inertial energy stored so it will go to complete stop very quickly .
in normal conditions this happens much faster due to friction losses in bearings ,air hitting the flywheel ,
vibration losses (flywheel wieght not alligned ; shafts not 100% balanced
and losessin the motor itself .
so to get this straigh there is no such free energy except generated by sollar panels or a turbine feed by high pressure water from a dam .
Dear clean energy Desi scientist , Energy can never be generated it's always transferred ,
Yes,this is called energy storage toy.
Can you see the electrons coming out of the plug in the wall ? we are living in a world of energy he's not building electrons or energy just capturing work in a way which is useful . you also need to realize that there is a huge amount of energy in the natural environment even at 0 degrees there is still 240 odd degrees to you get to 0 calvin . There was a guy years ago made the worlds most efficient heat pump using gases that boiled at -50 odd F so he was able to produce steam to drive turbine even if outside temps were low , he got sent to jail for literally no reason
@@chlyon Bro I called him up said the very same thing. He said that he would report me to cyber police
अभी भी अंग्रेज़ों को ही सिखना चाहते हो ! Sir ji हमारे भारत देश हिन्दी पढ़े लिखे लोग रहते हैं please हिन्दी में सिखाओ
This might sound crazy but if you stand this on its head so that the fly wheels are horizontal they will be easier to start rotating they will still produce the maximum stored kinetic energy but because they’re sideways the weight is distributed more evenly try it and you will find out this is true
Etwas dieser Richtung habe ich schon gedacht ,muss ja nicht Eisen sein ,Beton geht bestimmt auch gut
Leave it to the wonderful brilliant engineers of India to come up with a better way to make the necessary energy for life.
@Dave There are US companies also developing systems. Not sure about efficiency comparison.
x / r = 2(c-v) x (rn*c-(2cv)/sqrt of (n-3.14159) - (c2*2(r/v) / r(t-r + c/v) * 2(n-t) + (csqrt - 2(n-v). That was more simple than I thought. I'm glad I thunk it.
Eu queria saber o que significa estas fórmulas de física matemática. Para eu entender a ideia do senhor eu primeiro tenho que intender as suas fórmulas de física matemática, a única formula que eu entendo, é as fórmulas do cursinho do segundo grau que é Ec= M × V2 ÷ 2 = E =M × V2 =
Very nice job...you can open company and provide Electricity to village people
Any further development/break through in these six years? If one can get more output than input, this technique can be beneficially utilised for power production, is it not? Less pollution. More green.
Mr. Chaganti, Instead of arguing with everyone ehy don't you post such video which will clarify every thing in detail .As you say that 13 KVA will be available for two hours.....then post the video of two hours where whole world will see how you have produced free energy of 13 kva for two hours put that much load physically ( not show it on current meters or Volts meters.
Use a welding set or other loud
It hasn't got ANY chance of running that long under that load. Did you see the enormous generator taking up the full bed of a fairly large truck parked 50 feet down that driveway needed to gradually bring those flywheels up to speed too.
@@lorditsprobingtime6668 this chaganti guy is a fraud…it’s a shame that he is from the same city I’m from.
You can't get more energy out than you put in...? It's literally impossible.
any person with a bit of brain will agree its impossible ...what i cant wrap my mind is. Why do they think that if its bigger it works LAMO
i am not saying that i belive this man.... but just think about it why did he bother his time and waste his money making this giant Flywheel generator thing??? maybe its working and maybe its not. dont bash anyone if u didnt test it yourself yet... if it doasnt work so this guy is bullshit but what if it really work? u all will swallow ur shit bash.
When we do not know a subject we shut up.
That's what we heard about physics... But we should try because there are energies like vibrations, resonance, centrifuge, Gravity Acceleration we should know better.
The argument is: The large flywheel consume more energy than the Smaller flywheel causes the Generator to output:
Although the input power will be less than the output power, the step-down physical layout is where the losses are occurring.
They should be awarded the Nobel prize for creating energy efficiency more than 100%
If it were true and practical electricity prices would be dirt cheap!!!!!!!!
Sir cant you use the flywheel directly to a steam generator where it can substitute the turbine and there by reducing the friction and loss of energy from the turbines. Please others correct me if I'm wrong.
Fascinating concept, have you thought of using toothed drive belts that will not require as much tension so cutting down on the friction required for "V" belts.
in case of fly wheel tooth gear would be dangeorus . in case of any failure belt may slip but that weighted fly wheel will destroy the tooth gear
Y por qué no un acople magnético?
Boss stop saying particular particular, its making people getting irritation "Particularly your explanation crashing my brain very particularly"
hahaha.. i feel u brow..🤣🤣😂😂
Sr ji kha se milega yh
Now THAT is a flywheel!
congrats for your success sir , from 675 kw motor 1mw power is genrated . when 675kw motor (inductive load) is on and off frequently what about stability of grid
You have ate my brain in this particular vedio.
Can someone explain me why generators with fly wheel works only in Pakistan and India?
I think I have to change my country.
czcams.com/video/Enylbg2tlY4/video.html , Flywheel power Multiplication is the ultimate in clean and green energy generation regards Chaganti 8555045244
In these countries, electric meters are not used.
In other countries, Ohm's law is observed 100%.
yes this method work but just for 1-2 hr maximum after that you need to restart system again
Al Eladon because big companies don’t want you to have free energy but Pakistan and India fortunately not that commercial or sold to big companies
Dear brother,idont know what you are thinking about Pakistan, please don't compare my India to any other country in the world, because the extreme level of wealth and the technology is stolen from India and spreaded the rest of the world
Hi
This is a design
Exaggerated
I have a tip for you
These giant iron circles
I have a small idea
1 iron circle put in it
DC
The second iron is a circle, put in it
volt generation wires
Thus, the obstetric
automatic
My greetings
Sir...please make it available for all countries....poor people pay millions for electric power....spread it in your lifetime.... make it Available at once in global scale....then only it will come to india...Thank you.