Traxxas Unlimited Desert Racer (UDR) Shock Absorber Removal Service and Rebuild
Vložit
- čas přidán 3. 05. 2021
- In this Video we show how to remove and service the shock absorbers on the Traxxas Ultimate Desert Racer
We explain what shock oil to use and how to clean rebuild and bleed the shock absorbers
Finally they are refitted and watch out for next video showing how much better the truck now handles
Link to facebook page for the various 3D printed items which can be fully customised
/ customrc3dprints
#Traxxas #UDR #Shocks
Appreciate the vid mate 👍🏻✌🏼
How often did u run this truck in water? That messed up both of my diifs pretty badly.
So what other guides would people like to see? Leave a comment with your suggestions
Do you know a way to fix the original lightbars? I have three UDRs and and all of them do have at least one lightbar where some LEDs are blind or the brake light doesn‘t work. One good nosedive can already knock out some of the front grill LEDs.
Yes water will kill them. It will also kill the bearings. I am going to a Video on maintenance and recommended upgrades and how to minimise breakages
Thanks for this. I'm planning on trying different oil weight setup, this video will be useful. Quick question, do the dampers have any rebound on the UDR?
I don't set them up with any rebound. Because you have effectively 8 shocks then i don't think you need to. Let me know how it goes with the different oils. Just be aware that due to the geometry of the truck the rear needs a heavier oil than the front
Noted on the no rebound. Today I ended up filling it with (35wt) 400cst front & (60wt) 800cst rear. It's slightly more damping and firmer. However, I'm hoping the shocks will soften just a bit after a few more runs. Again, thanks for this video, much appreciated.
@@karimrachman5629 do u know what the stock oil weight is in the udr? I wanna change out my oil with slightly heavier oil
@@traxxas_cars160 60wt in the back and 30wt in the front
I’m contemplating buying a udr or saving for something else like an maxx. do you think the udr takes too much maintenance compared to the maxx
Have a look at some of our video and you will see Xmaxx v UDR
Hi, I can’t seeem to keep the blue rubber cap seated when I place the top shock cap on. It will screw down hand tight and the shock will feel good and smooth for a bit until I compress the shock 100%. Then it seems to blow the seal out of place. Do I need to tighten a bit more?
It’s tricky, use plenty of oil, check the diaphragm for any splits
@@TeamRC3D what worked for me was placing the cap securely in the shock cap and making sure it’s seated fully then placing the shock cap on the shock. Hey I also want to thank you for all your udr videos. They helped me tremendously. 🤜🤛
This doesn’t work. My shock keep leaking oil out of the top air hole. I don’t know what to do.
The blue think that looks like a contact lens keeps flipping inside the shock when I tighten it. It pops out of place.
Check to see if anything is damaged. It’s fiddly getting the diaphragm in
I got it to work. But my shock has lots of rebound. Is that something I should get rid of? If so would I just put less oil in it?
@@s_ckem6846 just need to bleed the shock again
Still won’t stop rebounding. All the air bubbles removed and all.
If you put some black tape on the teeth of regular pliers they won't scratch
Yes that would work as an alternative
How can I get a roof protector
Hi - drop a message through Facebook
facebook.com/customrc3dprints
Is that stand 3d printed ??
Yes it is we can supply the stands in a variety of colours - find us on facebook - link in description
Can I send you my shocks to do this service?
Yes we could organise something. Drop us a message on facebook facebook.com/customrc3dprints and we can discuss
Can i have one please..
Link to facebook page in description - drop a message on there
These trucks are water resistant not water proof. A puddle here and there is ok but going into rivers and streams is no good. Keep it out of the water, and stay in the dirt where it belongs.