Hi! I have a question - our geyser goes on at 5pm as we have a solar that heats it up during the day. When the water reaches its capacity 55 degrees and the 3 droplets are flashing - is it still using electricity? Or will it only use when the temperature drops and use to bring it back to 55 degrees? I’m trying to figure out the best solution to have warm water and save electric at night
Its difficult to give you an answer. I don't understand when you say " the water is still not going on". As for wanting to change the temperature, maybe your unit is faulty
Good video, thank you. I have a question, maybe you know the answer. At the moment when the solid 3 element lights come one, so the heating time slot is activated, my water temperature is not moving at all, not even a degree. The temperature at that time is below the max temperature it is set to and the lights are solid red (not flashing) indicating that it should heat and rise, but nothing happens. What could be the problem? I will be consulting the plumbers again that replaced my burst geyser, because this issue happened shortly after they installed the new geyser, but would like to know your opinion.
So when your water does not heat up, the element might be faulty. If you have a newer geyser, unlike mine, the new geyserwise also has a termostat thingamajic it comes with. That might also be your problem. Or your geyserwise is not set up properly. That is my 3 options for you to start looking at but bare in mind, I am no professional...hope you come right
@@bushieswatboer1876 The issue was fixed! In the end it was the geyserwise thermostat thingamajig, that was faulty, that needed replacing. It cost R550 excluding labour costs.
We usually get that if it was a very cold evening. All we do is switch off the geyser circuit breaker, wait 3seconds and switch it back on. This always clears the error for us
The spanner icon means that there is an error. Switch off the geyser circuit breaker and switch it back on after 3seconds. If the error remains, get a professional to look at it.
My gyserwise is showing that green little icon between and off, I tried to get some people going up to check because since that went on my water doesn't get hot from the sun anymore, can advise me please? Big Thanks
I normally just switch off the geyser circuit break at the main DB-board. Wait few seconds and then switch back on. If that does not work, then it's time to call a professional
Hallo there, can you please tell me what is the difference between the TSE and the MAX Geyser Wise controllers, because there is quite a huge gap in price between the two.
That question I cannot answer. We bought the house with this system and I am not even aware of other systems. Best is to go the supplier and ask them to explain the difference
@@bushieswatboer1876 Thank you so much, I am looking for a rather inexpensive geyser timer to only run a geyser for two to three hours per day. Nothing fancy just a simple on off timer that will not lose settings during load shedding.
@@bushieswatboer1876 I am confused why you need your temperature so high, I personally think for me 45 is more than enough. Does your geyser have a blanket and are the pipes foam insulated?
@@philipgrobler7253 You just answered yourself by saying, "I personally think..." the temperature is a personal preference. At 45, I do not enjoy the shower at all. My geyser has no blanket and the pipes are 50% foam insulated
The name of the channel is great.
Hallo sir, good explanation
Hi! I have a question - our geyser goes on at 5pm as we have a solar that heats it up during the day. When the water reaches its capacity 55 degrees and the 3 droplets are flashing - is it still using electricity? Or will it only use when the temperature drops and use to bring it back to 55 degrees? I’m trying to figure out the best solution to have warm water and save electric at night
When flashing, no escom used, but is potentially available. So when temp drops to ,say 53, it will use escom again to heat up to 55 again.
The water is still not going on and on that position that has 54 degrees, it shows 20 and I can’t change it 💔💔💔
Its difficult to give you an answer. I don't understand when you say " the water is still not going on". As for wanting to change the temperature, maybe your unit is faulty
Good video, thank you. I have a question, maybe you know the answer. At the moment when the solid 3 element lights come one, so the heating time slot is activated, my water temperature is not moving at all, not even a degree. The temperature at that time is below the max temperature it is set to and the lights are solid red (not flashing) indicating that it should heat and rise, but nothing happens. What could be the problem? I will be consulting the plumbers again that replaced my burst geyser, because this issue happened shortly after they installed the new geyser, but would like to know your opinion.
So when your water does not heat up, the element might be faulty. If you have a newer geyser, unlike mine, the new geyserwise also has a termostat thingamajic it comes with. That might also be your problem. Or your geyserwise is not set up properly. That is my 3 options for you to start looking at but bare in mind, I am no professional...hope you come right
@@bushieswatboer1876 The issue was fixed! In the end it was the geyserwise thermostat thingamajig, that was faulty, that needed replacing. It cost R550 excluding labour costs.
@@abizziegirl glad you got it sorted. Stay blessed
What does it mean when the red droplets are flashing/flickering?
It means your water reached the temperature you set it to and still warming up
What do you do when the system shows a E4 error and keeps flicking, the water never goes hot anymore
We usually get that if it was a very cold evening. All we do is switch off the geyser circuit breaker, wait 3seconds and switch it back on. This always clears the error for us
My water temperature is very low and what does the spanner icon on the device mean?
The spanner icon means that there is an error. Switch off the geyser circuit breaker and switch it back on after 3seconds. If the error remains, get a professional to look at it.
Spanner means the pump is running. Errors are E# flashing on the unit
My gyserwise is showing that green little icon between and off, I tried to get some people going up to check because since that went on my water doesn't get hot from the sun anymore, can advise me please? Big Thanks
That means that there is something wrong with the system and you need a professional to come out.
Hello myne shows a E1
What do I Do please help
I normally just switch off the geyser circuit break at the main DB-board. Wait few seconds and then switch back on. If that does not work, then it's time to call a professional
Hi mine show E7 error code
I usually switch off the geyser circuit breaker for a few seconds and then back on. If that does not work, get a professional in
We have the same thing but hoe come the water is not hot on 55
It might be your element that is the problem or the probe connected to the system does not pick up the correct temperature
How to install not how it works
Unfortunately, we bought the house with it installed already.
Hallo there, can you please tell me what is the difference between the TSE and the MAX Geyser Wise controllers, because there is quite a huge gap in price between the two.
That question I cannot answer. We bought the house with this system and I am not even aware of other systems. Best is to go the supplier and ask them to explain the difference
@@bushieswatboer1876 Thank you so much, I am looking for a rather inexpensive geyser timer to only run a geyser for two to three hours per day. Nothing fancy just a simple on off timer that will not lose settings during load shedding.
@@bushieswatboer1876 I am confused why you need your temperature so high, I personally think for me 45 is more than enough. Does your geyser have a blanket and are the pipes foam insulated?
@@philipgrobler7253 You just answered yourself by saying, "I personally think..." the temperature is a personal preference. At 45, I do not enjoy the shower at all. My geyser has no blanket and the pipes are 50% foam insulated
@@philipgrobler7253 so our system keeps its settings even if the power went off. Only the time will be off sometimes
Don't get it
You can't just leave a response like that without saying why
My keypad just flashing 88888888s. No buttons are working
You should consult your manual. If all else fails, consult a professional. Remember I only share info if I experienced it.
@@bushieswatboer1876 I switched the DB board off for a few mins and it worked