Thank you very much. I haven't tried the code yet, but I'm sure it will be fine. However, I had to file down the servo horns a lot to make them fit in their places. Length-wise it's not a problem, it's the width. And the holes don't match up. I've ordered other models for the next one ;) - Actually, I'm going to build the vehicle shown in the other video, but I prefer to separate the steps. Projects: general surveillance and scaring pigeons.
I am a newei and I have got an another problem 😅 Now the video gets freezed whenever I try to stream the video. Also I am only able to use it when I am connecting it through arduino to laptop. ESP32 doesn't start when I power it external 5v supply without the RX, TX pins. It's only working when I am connecting the RX, TX pins of arduino with it.
Thank you for checking out the video and suggestion 👍 The noise comes from Servo motors used as these are very cheap servos and has plastic gears. It can be avoided using better servos with metal gears .
the servo motor you used were from miuzi and the link you provided was tower pro which i bought and were totally useless. can you provide link for the miuzi servo motors. can you tell me where you buy parts from
Thanks for checking out the video 👍 Good to hear that you are making progress in this project . What issue are you facing with servo ? Make sur to provide proper power supply of 5v dc.
@@hashincludeelectronics Thanks so much for your reply! I am using a 27-watt 3v-7v adjustable voltage power supply, which is set at 5v. The Servos are not responding to slider adjustments.
Thanks sir , since I have made a drone I want to add a camera which can record and send to phone but there is no video of it soo i searched for wireless cctv and this was helpful I can add it to my drone soo i can stream in phone thank you sir also can u pls Say me how to make the camera and the phone connection range long
Thanks for checking out the video 👏🏻👍🏻. It’s nice to hear that you are working on drone and want to add camera functionality in it . However this project has very limited range like wifi . However if you want to increase the range then you might have to connect the antenna. 👏🏻👍🏻
@@hashincludeelectronics Can u make a video about it soo i can understand clearly since I don't know properly of making things because I don't have the essential required stuff
I want to build this project so I can connect to it any place in the world. Can I use an external internet access for the esp32 cam instead of my phone so I can have acces to it anywhere in the world and can I be able to control the servo any place in the world? Thanks
Unfortunately it can not be done using this project . This camera can be accessed locally only . You need to use the party apps like Blynk to access the camera globally from anywhere in the world . Unfortunately I don’t have video using Blynk on my channel . You can check for reference on internet . 👌🏻👏🏻
@@hashincludeelectronics Okay. I thought it is webserver connected already. For example, I just need a router for the esp32 cam then while internet connected it streamed the video live to my phone at another country after turning ON my mobile data. Also, why is blynk different from this. I think they plan the same source as you either need a web or app so you can stream the live video.
@@joshuaolaiya you can not connect to your local routers IP from outside . And even though you open port externally somehow , it’s dangerous . When using Blynk we send data to Blynk server first . And then from mobile we connect to Blynk server and receive the data.
Bro I am providing it 5v supply but I think it's less than 2 A. Since I am not using sevo but still the video is freezed. Is it because of A? Is it necessary to provide 2A for video streaming
Hello sir.... I have also made it looking like this. But problem is coming. The video is not playing and stops after showing only 1 second and the servo motor is also not running. Only the LED function is working.
A compilation error is coming ' ledcsetup not declared in this scope ; did you mean ledc_stop ' Also coming for ledcattachpin How to solve ? Please help 🙏🏻
hi nice video, can you explain more why we need the dummy servos for the libraries to not interfere ? i am attempting a similar project, and i notice that when my servos are connected, the esp32 fails and continuously reboots.
Actually it was to avoid the conflict between timers used by servo and cam . But if you check my recent videos we don’t need dummy servos at all . I have fixed that problem . 👍🏻👏🏻
Hello friend, first of all, the project you have made is very nice, I congratulate you and I have a question for you. I will move this system to the v4 port of my modem. I need to connect it to the modem. What changes should I make in the code to connect it to the modem?
Thank you very much for your nice comment . 👍🏻👏🏻. To answer your question , you will have to AP WiFi mode in the code . You can check my getting started with esp32 video to see how we can connect to modem using AP mode 👍🏻👏🏻
esp_camera.h: No such file or directory, it shows after all what you said adding link in preferences, esp32 board downloaded, and added both libraries ASYNCTCP and websocket
I accidentally erased the esp32 json file in preferences, so i searched for the url again and loaded it. NOW, using the same code as yours, all I get is "Error compiling for board AI Thinker ESP32-CAM. " Please guide me to a solution as I have exhausted everything that I can think of. I noticed that if I use WebServer, instead of AsyncWebServer, the code installs without error, but the images do no work. HELP !!!
I have a question: if I want to use only one servo motor, then add a PIR sensor and a piezo buzzer, do I also need dummy pins for each component? Or are dummy pins only necessary for the servo motor? Thank you, please answer.
A very much useful video for the current project I'm doing. Kindly can you please tell me how this can be make possible on a drone to view and get the video. It means a lot if you would help for this. Thank you ☺️
Hey there I'm having a problem with the live video it doesn't seem to be showing up for me. I've also noticed that the servo doesnt work even though i've followed all of you instructions in the video including the max messages queue and reupload the code
I don’t have steps for these however you can check on internet for more details. I will take a note of it and probably will create video for the same 👍🏻👏🏻
@@hashincludeelectronics Thank you very much for your reply. Ask because of my intended model train application. I'd like to mount on model train flatcar ... it would be nice to see forward, backward as well as right and left as train goes around layout.
Thanks for checking out the video. You need to upload the code into esp32cam module and restart it. Once done try to see if its available in wifi in your mobile. If not then try restarting your Wi-Fi on mobile.
Oh tht nice but can u explain the Arduino part i tried but it failed i didn't know how to do it . If u could help me I will be very thankful I will try the robotic arm which u have made its was awesome ur explanation tho it's nice bro Tho i have a doubt i wanted to purchase a 4DOF robotic arm is tht code applicable for tht which is a 3DoF Those both look quite similar pls reply sir❣️
hlw sir i am facing a problem... it is that the video is not streaming and when it streams its just a snapshot only and then it freezes and i cant help it...the serial monitor says frame buffer not accquired... i have also set the parameter to 1 as described in the video... plzzz reply sir plz help me
great work! I have a question: Does it need to be on the same Wi-Fi network? I want to control it from a distance. Do you have any suggestions on how I could do that?
Hi nice video but, The Pan and tilt servos not working when i try it. Also the video is not working I only get a still picture even after changing the setting from 32 to 1, the only thing that works is the flashlight.
I follow your guide with code but video didnot stream, the screen only a picture when camera turn on. I couldn't control pan and tilt servo, but the light can turn on or off. I used different power for ESP32 Cam and servos. Anyone can help me to solve this problem? Thankyou!
i've issue my adapter was blinking when plugging to esp32 cam. My adapter 5v 2A just normally no problem in other. i confused in this, where's the problem..
I've tried according the video. Uploaded the code in esp32 without any error. then when I've giving power with 5v 2a adapter. SSID works. After connecting to ssid. Only LED control working. Camera video is freezed and no servo is working. I've also set the WS limit to 1. But still no movement in servos and no live video footage. Please give me a permanent solution
Please check the power supply . It should provide more than 2A current to work . Also check if your servos are freely moving . It should not get stuck in the frame 👏🏻👍🏻
sir after connecting the battery i am unable to get the video and also the motors are not functioning but i am able to control the led flash light .can you tell me what device or method to be applied to get the proper output
@@hashincludeelectronics Thank you for answereing, I was indeed missing hat step, but even after fixing that it still forzes after a sew frames and then only the LED brigthess control works and also gives the message "Frame buffer could not be acquired" in the serial monitor :(
Hi, Great project, i have build one and both the servos are woking fine. but the video is not coming and if coming its just a snpshot only. in serial monitor i am getting "Frame buffer could not be aquired" please suggest on how to resolve this. Thanks
Thanks for checking out the video 👍🏻👏🏻. You need to set one parameter as shown in video . Please check video and see how to set “max messages queued” variable . 👍🏻that will solve the issue .
I want to implement this project: "Design of Driver Awareness system depending on Eye and Face Feature and Discrimination" Can I use ESP32 instead of Raspberry Pi ? please reply
You can use esp32cam however you will have to do more study on how to use it for object detection etc . 👍🏻👏🏻please check details on internet available 👍🏻
hello! as soon as i saw this video i wanted to make this project, but i am stuck in middle. the issue is that cam module is not streaming the video instead it is just capturing a image at that instance when it is getting connected to my phone. What should i do ? please help me.
Can I combine this project with your other video named “Surveillance Car using ESP32 Camera Module"? If yes, what should be the changes that will occur in its code and the wiring
please help me. When I tried to copy the code and I touch to upload button in the Arduino IDE but it didn't upload. I downloaded the Esp32 board, the AcyncTPC library, and the ESPAsyncWebServer library. Arduino's 5V is connected to 5V, GND to GND, UOT to TX, UOT to RX, RESET to GND, GPIO 0 to GND. But even if the computer sees the Arduino Uno card, it does not upload code. İt gives a "fetal error".
Yeah this error is common . There are many solutions for this . Try pressing enable button while uploading the code . Try using different USB port . Or cable . Check on internet for information on this error . It should be solved 👍🏻
@@ameerpasha9941 yes I was able to solve. I just changed the port of the Arduino Uno card a few times, tried to reload and it worked. That's how I solved the problem. If you solve, you write the answer;)
congratulations to the project, I just thought that the response time of the camera is much higher than the native webserver project, is there a way to make the camera refresh faster?
Thanks for checking out video 👍🏻 . Yeah camera image capture is faster however the transfer of image through Websocket limits the FPS for video . It’s the best I could do with this webserver . I would be glad if there is other way to improve it for more FPS. But for now don’t see any way to improve it further . The video is still responsive enough with VGA quality .
I have a basic question.i m getting a esp32 board..... should i get the cam version or the plain esp32.....does the cam version have all the functionality of normal esp32...since number of pins in esp cam are half the number of non cam version
It depends upon your project need . Does your project need camera in it ? If yes then go for esp32cam . Else if you are starting with esp32 then buy simple esp32 module of 38 pins . Yes both the modules will almost function same with esp32 having far more number of pins than cam module.
Uploading the code from arduino uno to esp32 cam board is not working for me. It's saying failed to connect to the esp32 board and there is no serial data received.
@@hashincludeelectronics thank you for quick reply , I did exchanged two SERVOs pin and tried all pins of ESP32CAM, only pin12 drived both SERVOS, other pin not...
Hello! i get this error whenever i want to upload the code - A fatal error occurred: Failed to connect to ESP32: Timed out waiting for packet header. Can you help me please?
Good day Sir, I faced a problem which is when I try to control my servo motor it will auto disconnected the wifi connection. Is it because of the current provided to the motor doesn't enough? But for the ESP32 CAM and the lightning control works well
@@hashincludeelectronics i mean, can we use esp 32 cam station mode instead of setting it as access point ? (in your project phone connects to esp32 cam, but i want to connect esp32 cam to phone's hotspot)
@@psykopat81 yea you can . However what are you trying to achieve by doing this ? If you connect to your mobiles hotspot then you will have to get the ip address from esp32 which will be different.
@@hashincludeelectronics i am controlling my old android phone with teamviwer. If the esp32 cam is connected to the hotspot of this phone, I could control the esp 32 cam from anywhere in the world (you know blynk video streaming is now paid). If the phone is connected to the esp32 cam via wifi, the mobile connection is automatically closed and I cannot connect to my old phone. So the phone's mobile connection must remain open and esp32 must be connected to the phone.
Hi sir can you control by using MIT App inventor App imventor should contain esp32 camera, pan and tilt controls,arrows for controlling car f,b,l,r Plz make this for your new subscriber plzzzzzzzz😢😢😢😢😢😢
Please help.. When I uploaded the code after doing connection properly it was working properly. So I have disconnected the supply and I was happy. But after some time I again connected the supply and the problem starts from here. At first when I was trying to connect the wifi it connects and getting disconnected quickly. But now no hotspot is coming from the esp32 cam module as I can't see from the wifi section of my phone. So I have reset the board and uploaded the code again but still same problem. Please give me the solution.
I have just made this and it's working perfectly. Thank you Sir for sharing!! Well done.
I am glad that it worked perfectly well 👌🏻👏🏻. Good job 👍🏻
hlw brother mine is not working perfectly can u help me
@@hashincludeelectronics I can't access the IP address. What's the problem with the IP? Is it a bug/error?
Thank you very much. I haven't tried the code yet, but I'm sure it will be fine. However, I had to file down the servo horns a lot to make them fit in their places. Length-wise it's not a problem, it's the width. And the holes don't match up. I've ordered other models for the next one ;) - Actually, I'm going to build the vehicle shown in the other video, but I prefer to separate the steps. Projects: general surveillance and scaring pigeons.
Thanks for checking out the video 👍🏻👏🏻. Good luck for your project . 🙂
This video is ultra mega useful thank you!
Glad you think so!
can you add 2 buttons below the sliders
Ultra mega pro Max plus useful
Bro what is the amp of 5v ac-dc adapter
It should be more than 2A .
Thank you bro
Can we use mobile charger with 5v 3A
I am a newei and I have got an another problem 😅
Now the video gets freezed whenever I try to stream the video. Also I am only able to use it when I am connecting it through arduino to laptop. ESP32 doesn't start when I power it external 5v supply without the RX, TX pins. It's only working when I am connecting the RX, TX pins of arduino with it.
OMG, I found exactly what I wanted to do. Thank you very very much.
That’s nice 👍🏻I am glad that it helps you .
Great video. Exactly what I was looking for 👍🏼
Will use it with esphome
Awesome 👏🏻
@@hashincludeelectronics I can't access the IP address. What's the problem with the IP? Is it a bug/error?
Thank you ... will be my next project to use with model trains. All the best to you!!!
Thank you 👏🏻
Amazing...just one observation which u can consider : Camera movement is bit noisy
Thank you for checking out the video and suggestion 👍 The noise comes from Servo motors used as these are very cheap servos and has plastic gears. It can be avoided using better servos with metal gears .
Excellent video with proper explanation 🙌
Thank you very much and I am glad that you liked it 👍🏻
the servo motor you used were from miuzi and the link you provided was tower pro which i bought and were totally useless.
can you provide link for the miuzi servo motors. can you tell me where you buy parts from
You can buy any micro servo motor 👍🏻👏🏻
Thanks for the video I am struggling to get my servos to actually work, however everything else seems to work just fine.
Thanks for checking out the video 👍 Good to hear that you are making progress in this project . What issue are you facing with servo ? Make sur to provide proper power supply of 5v dc.
@@hashincludeelectronics Thanks so much for your reply! I am using a 27-watt 3v-7v adjustable voltage power supply, which is set at 5v. The Servos are not responding to slider adjustments.
@@jeremyviny6817 that’s good enough supply . Where are you checking this ? On mobile or on laptop? It only works on touch screen device
@@hashincludeelectronics I am using my phone so think the issue might be elsewhere :(
@@jeremyviny6817
I have the same problem. One of the vertical servo motors does not respond to the slider adjustments. Did you find the solution?
@hashincludeelectronics Awesome video brother thnx for sharing this but i have a question what is the range of this model
Thank you very much for checking out the video . 👏🏻👍🏻. The range is around 60-80 ft .
Thanks sir , since I have made a drone I want to add a camera which can record and send to phone but there is no video of it soo i searched for wireless cctv and this was helpful I can add it to my drone soo i can stream in phone thank you sir also can u pls Say me how to make the camera and the phone connection range long
Thanks for checking out the video 👏🏻👍🏻. It’s nice to hear that you are working on drone and want to add camera functionality in it . However this project has very limited range like wifi . However if you want to increase the range then you might have to connect the antenna. 👏🏻👍🏻
@@hashincludeelectronics Can u make a video about it soo i can understand clearly since I don't know properly of making things because I don't have the essential required stuff
I want to build this project so I can connect to it any place in the world. Can I use an external internet access for the esp32 cam instead of my phone so I can have acces to it anywhere in the world and can I be able to control the servo any place in the world? Thanks
Unfortunately it can not be done using this project . This camera can be accessed locally only . You need to use the party apps like Blynk to access the camera globally from anywhere in the world . Unfortunately I don’t have video using Blynk on my channel . You can check for reference on internet . 👌🏻👏🏻
@@hashincludeelectronics Okay. I thought it is webserver connected already. For example, I just need a router for the esp32 cam then while internet connected it streamed the video live to my phone at another country after turning ON my mobile data. Also, why is blynk different from this. I think they plan the same source as you either need a web or app so you can stream the live video.
@@joshuaolaiya you can not connect to your local routers IP from outside . And even though you open port externally somehow , it’s dangerous . When using Blynk we send data to Blynk server first . And then from mobile we connect to Blynk server and receive the data.
@@hashincludeelectronics Alright noted. Thank you
@@joshuaolaiya welcome 👍🏻
This is cool better than ip cam
Thanks for checking out the video 👏🏻👍🏻
A great video, thanks for sharing and good luck with your projects.
Thank you very much and I am glad that you liked it 🙂👍🏻 Stay tuned for more such interesting project 👍🏻
Bro I am providing it 5v supply but I think it's less than 2 A. Since I am not using sevo but still the video is freezed. Is it because of A? Is it necessary to provide 2A for video streaming
You need to change one setting in code . Please check for this step in video 👍🏻👏🏻
Hello sir....
I have also made it looking like this. But problem is coming. The video is not playing and stops after showing only 1 second and the servo motor is also not running. Only the LED function is working.
What is causing this problem? Why is this happening? And why is the camera module ESP 32 getting hit?
You need to change one setting in code . Max messages queued . Please check this in video 👍🏻👏🏻
@@hashincludeelectronics 32 to 1
I have done this also
I need to use the same on drone for movement, but the components have more weight than I need. Any alternatives, you can suggest?
Can u please make it gesture controlled.
For example if you turn your hand around, camera should turn in same direction.
Will try 👍🏻👏🏻
thanks sir for this wonderful tutorial, I was wondering if how can I add a relay switch on the esp32 cam
Thank you very much for checking out the video 👍🏻. You can check my other videos on esp32 cam module for reference .
A compilation error is coming ' ledcsetup not declared in this scope ; did you mean ledc_stop '
Also coming for ledcattachpin
How to solve ? Please help 🙏🏻
Please install 2.0.16 version of esp32 board 👍🏻👏🏻
hi nice video, can you explain more why we need the dummy servos for the libraries to not interfere ? i am attempting a similar project, and i notice that when my servos are connected, the esp32 fails and continuously reboots.
Actually it was to avoid the conflict between timers used by servo and cam . But if you check my recent videos we don’t need dummy servos at all . I have fixed that problem . 👍🏻👏🏻
@@hashincludeelectronics nice. I found you can also fix it by not using the servo library, and using delays for software PWM
Hello friend, first of all, the project you have made is very nice, I congratulate you and I have a question for you. I will move this system to the v4 port of my modem. I need to connect it to the modem. What changes should I make in the code to connect it to the modem?
Thank you very much for your nice comment . 👍🏻👏🏻. To answer your question , you will have to AP WiFi mode in the code . You can check my getting started with esp32 video to see how we can connect to modem using AP mode 👍🏻👏🏻
esp_camera.h: No such file or directory, it shows after all what you said adding link in preferences, esp32 board downloaded, and added both libraries ASYNCTCP and websocket
Please select proper board while uploading the code 👍🏻👏🏻
@@hashincludeelectronics now getting this error-Compilation error: 'ledcSetup' was not declared in this scope; did you mean 'ledc_stop'?
Hello ! Mine is bugged, it connects but the image doesn't refresh. Is there a way to fix it plz ? Thanks !
You need to change one setting in code . Please check the video for this step 👍🏻👏🏻
I accidentally erased the esp32 json file in preferences, so i searched for the url again and loaded it. NOW, using the same code as yours, all I get is "Error compiling for board AI Thinker ESP32-CAM.
" Please guide me to a solution as I have exhausted everything that I can think of. I noticed that if I use WebServer, instead of AsyncWebServer, the code installs without error, but the images do no work. HELP !!!
Which version of esp32 did you install ? Please install only 2.0.16 version of esp32 board 👍🏻👍🏻
I have a question: if I want to use only one servo motor, then add a PIR sensor and a piezo buzzer, do I also need dummy pins for each component? Or are dummy pins only necessary for the servo motor? Thank you, please answer.
We don’t need dummy pins for other components 👍🏻👏🏻
This project and line follewer car combining ? How can we do
Unable to upload code at all with ft232r module so i have ordered cp2102 usb to ttl module
Sir i finish the project. But pan,tilt servo and camera not working.but flash light working perfectly. What i do?
Please check the connections . Also make sure you use good power supply 👏🏻👍🏻
A very much useful video for the current project I'm doing. Kindly can you please tell me how this can be make possible on a drone to view and get the video. It means a lot if you would help for this. Thank you ☺️
Thank you very much for checking out the video 👍🏻. This will not have enough range for drone .
Can you teach me how to rotate the screen video please.
You need to fix the esp32 cam as shown in video . Not sure if that will help 👍🏻👏🏻
I am using your code and following your video. However I get an error "Frame buffer could not be acquired" What could I be doing wrong
You need to update one setting in code . Please check the cheek for this step 👍🏻👏🏻
Hey there I'm having a problem with the live video it doesn't seem to be showing up for me. I've also noticed that the servo doesnt work even though i've followed all of you instructions in the video including the max messages queue and reupload the code
Check the connections please 👍🏻👏🏻
how to program to record video from esp32 cam and save it on sd card
I don’t have steps for these however you can check on internet for more details. I will take a note of it and probably will create video for the same 👍🏻👏🏻
Could this be modified to use with 360 degree servo to get 360 degree pan capability? Thanks for your attention.
Yes it can be. Just change the slider values in code. min and max values for pan slider to 0-360.
@@hashincludeelectronics Thank you very much for your reply. Ask because of my intended model train application. I'd like to mount on model train flatcar ... it would be nice to see forward, backward as well as right and left as train goes around layout.
Hey can anyone tell, where to change that important settings part???
Please check the video for details 👍🏻👏🏻
Hi, thanks for your great ideas, I have a question, I never see the NowISeeyou SSID, how am I suppose to get that?
Thanks for checking out the video. You need to upload the code into esp32cam module and restart it. Once done try to see if its available in wifi in your mobile. If not then try restarting your Wi-Fi on mobile.
plz i need help i keep getting this error : The esptool_py tool is not available for your operating system.
Please use Arduino IDE and install esp32 board in it 👍🏻👏🏻
Bro this is Bluetooth operated right or u have to give the live connection to the Arduino
This is WiFi operated. But you don’t need internet for this . This project creates its own WiFi network .
Oh tht nice but can u explain the Arduino part i tried but it failed i didn't know how to do it . If u could help me I will be very thankful
I will try the robotic arm which u have made its was awesome ur explanation tho it's nice bro
Tho i have a doubt i wanted to purchase a 4DOF robotic arm is tht code applicable for tht which is a 3DoF
Those both look quite similar pls reply sir❣️
Please can you make a video on how to capture and save image on laptop using esp 32 cam please
hlw sir i am facing a problem... it is that the video is not streaming and when it streams its just a snapshot only and then it freezes and i cant help it...the serial monitor says frame buffer not accquired...
i have also set the parameter to 1 as described in the video...
plzzz reply sir plz help me
Please recompile the code and upload again . And then try 👍🏻👏🏻
can i use li-battery3.7vx3 (850mahx3) for this testing ? because i found my 2 servo has no any motion.
Yea you can 👍🏻
great work! I have a question: Does it need to be on the same Wi-Fi network? I want to control it from a distance. Do you have any suggestions on how I could do that?
yes,it needs to be on the same wi-fi network and you need another outsourced server to control it more remotely like blynk..
Very good 👍👍👍
Thank you very much
Uploaded the code but camera just doesn't stream all I get is frozen still pic. Do you have a solution for this problem? great vudeo
You need update one setting in code . Please check the video for this step 👍🏻👏🏻
I got it working i was trying to get the esp32 to connect to my router but no luck
Hi nice video but, The Pan and tilt servos not working when i try it. Also the video is not working I only get a still picture even after changing the setting from 32 to 1, the only thing that works is the flashlight.
Please check the video slowly and carefully for any missing step 👍🏻👏🏻
Ok thanks
I follow your guide with code but video didnot stream, the screen only a picture when camera turn on. I couldn't control pan and tilt servo, but the light can turn on or off. I used different power for ESP32 Cam and servos.
Anyone can help me to solve this problem? Thankyou!
You need to update one setting max messages queued . Please check the video for details 👍🏻👏🏻
@@hashincludeelectronicsIt's ready, I have changed from 32 to 1 as your guide.
i've issue my adapter was blinking when plugging to esp32 cam. My adapter 5v 2A just normally no problem in other. i confused in this, where's the problem..
Remove the servos and just try connecting to esp32 only . See if it works . May be servos are causing issues .
@@hashincludeelectronics servo isn't problem i was checked and test
@@hashincludeelectronics then i press reset button esp32cam, the esp led is blinking too
Thank you sir for this code and setup explanation. And i have question sir can we use a battery for power supply
Yes you can use battery . However you need to make sure battery provides exactly 5V . Also use only rechargeable battery 👍🏻👏🏻
OK sir thank you for your guidance.
@@sumeetmurgod2211 welcome 🙏
I've tried according the video.
Uploaded the code in esp32 without any error. then when I've giving power with 5v 2a adapter. SSID works. After connecting to ssid. Only LED control working. Camera video is freezed and no servo is working.
I've also set the WS limit to 1. But still no movement in servos and no live video footage.
Please give me a permanent solution
Please check the power supply . It should provide more than 2A current to work . Also check if your servos are freely moving . It should not get stuck in the frame 👏🏻👍🏻
@@hashincludeelectronics okay. the servo is not moving. when i'm disconnect the 5v pin, that time the servo just giving a shaking.
sir after connecting the battery i am unable to get the video and also the motors are not functioning but i am able to control the led flash light .can you tell me what device or method to be applied to get the proper output
same problem
I also got same problem please tell what can be the solution for it
Sir, I am facing this problem " esp_camera.h " file not found. Now what should I do? Please sir help me, Love from Bangladesh ❤️
Please install the esp32 board as shown in video . Also select proper board while uploading the code in Arduino IDE 👏🏻👍🏻
@@Rayhan_Ahmed.Use laptop or computer
Great job. Is it possible to add taking a picture and recording video? If yes....how I can do it?
Yes we can use SD card and store pics. But it will need lot of code changes . 👍🏻👏🏻 you can refer some material on internet for this 👍🏻
I'm struggling with this, for some reason the esp32 just gives me one image and then it does not update anymore and I still can't figure out why :(
You need to change one setting in code . Please check the video for this step 👍🏻👏🏻
@@hashincludeelectronics Thank you for answereing, I was indeed missing hat step, but even after fixing that it still forzes after a sew frames and then only the LED brigthess control works and also gives the message "Frame buffer could not be acquired" in the serial monitor :(
how can i use moibe data (i wanna not use local modem )
Please check my video on getting started with esp32 for Station mode 👍🏻👏🏻
Sorry sir I commented again since u didn't reply to my last answer I gaved
Can u please explain me how to increase the range of it
You can add antenna to esp32 cam module . However you need to check for this step on internet 👍🏻👏🏻
@@hashincludeelectronicsreplying after 5 month thanks it was really useful
Hanzhen harmonic drive gear , strain wave reducer,
robot joint, over 30 years experience
👍🏻
Great project. Is it possible to add a label with a sensor value on a web page? If yes....how I can do it?
You can do it with thinkspeak and eith api in your code
This is Great 👏🏻
Thank you very much 👍🏻 cheers 🍻
Hi, Great project, i have build one and both the servos are woking fine. but the video is not coming and if coming its just a snpshot only. in serial monitor i am getting "Frame buffer could not be aquired" please suggest on how to resolve this. Thanks
Thanks for checking out the video 👍🏻👏🏻. You need to set one parameter as shown in video . Please check video and see how to set “max messages queued” variable . 👍🏻that will solve the issue .
hi sandeep, did your problem got solved because i am facing the same problem
@@hashincludeelectronics hi me too facing the same problem, i follow the step " 32 to 1 " but the problem still goes
my serial monital show"psram initialized. malloc to take memory from psram above this size" what it mean and howto fix i?
I believe you are missing some step . Please check the video for any missing step . 👍🏻👏🏻
HEY can i get the stl file of servo part, i know you order it online however by any chance you have it/arrange it.
Thanks
Unfortunately I don’t have it 👍🏻👏🏻
@@hashincludeelectronicsThank you for your comment, no worries! I got it anyway.
@@MuhammadQasim-kw1er awesome 👍🏻
Hello, this text is showed in serial monitor "Frame buffer could not be acquired". How can I fix it?
You need to change one setting in code . Please check the video for this step 👍🏻👏🏻
@@hashincludeelectronics I already change it, but it still does not working.
Also the servo is not working. Can you help us? we will use it in our capstone project
Great video... keep it up and make more.
Thank you very much 👍🏻
I want to implement this project:
"Design of Driver Awareness system depending on Eye and Face Feature and Discrimination"
Can I use ESP32 instead of Raspberry Pi ? please reply
You can use esp32cam however you will have to do more study on how to use it for object detection etc . 👍🏻👏🏻please check details on internet available 👍🏻
hello! as soon as i saw this video i wanted to make this project, but i am stuck in middle. the issue is that cam module is not streaming the video instead it is just capturing a image at that instance when it is getting connected to my phone. What should i do ? please help me.
You need to update one setting related max queued messages . Please check the video for this step 👍🏻👏🏻
bro, how to setting WS_MAX_QUEUED_MASSAGE to 1?
Please check the video for this step 👍🏻👏🏻
Im using a 6v AA battery. Is that the reason why my camera not functioning and the prototype keeps on disconnecting?
Yes exactly. Please use rechargeable battery only .
Hello i need help, when i try to compile the code, it appears the error 'class AsyncWebSocketClient' has no member named 'queueIsFull' 🤔🤔
Have you downloaded the correct library and version ? Please uninstall any previously installed library and install again 👍🏻👏🏻
It shows connected without internet to NowISeeYou ssid. The light works well but the servos show no motion at all. Any solution??
It should be connected to this ssid only . Please check the video 👏🏻👍🏻
Sir can you please help me I am facing an error related to AsyncTCP Library saying no such file or directory
You need to install those libraries . Please check the video for steps 👍🏻👏🏻
Nice project! Could you tell me which mobile app to use? Thank you.
The mobile app code is inbuilt in Arduino code itself . It uses html and JavaScript 👌🏻👍🏻
Camera has been stuck
And saying error camera frame could not be acquired,how to solve this problem
You need to change one setting in code . Please check video for this step 👍🏻👏🏻
Awesome project!
Thank you very much . I hope it helped you 👏🏻👍🏻
Hey you, do you have any video how to make a webserver for esp32
You can check my video on getting started with esp32 👍🏻👏🏻
Can I combine this project with your other video named “Surveillance Car using ESP32 Camera Module"? If yes, what should be the changes that will occur in its code and the wiring
There is already a video on my channel where I have used pan tilt camera in car . Please check that 👍🏻
@@hashincludeelectronics
Can I get the model for the 3D printing?
I like it but which app does it use?
Thank you for checking out the video . The app is inbuilt in car code . It is made using html and JavaScript 👍🏻👏🏻
How can we fine tune the Servos to be more precise or less jittery?
You can try adding some delay if possible 👍🏻👏🏻
I can't access the IP address. What's the problem with the IP? Is it a bug/error?
Help me sir
Thanks a lot for this video from Kazakhstan. At the moment 4.54 , what link did you write in "Additional Boards ds Manager URLs"?
Thank you very much 👍🏻it’s link is given in the video just around 4:56. Also it’s provided in the description of the video .
please help me. When I tried to copy the code and I touch to upload button in the Arduino IDE but it didn't upload. I downloaded the Esp32 board, the AcyncTPC library, and the ESPAsyncWebServer library. Arduino's 5V is connected to 5V, GND to GND, UOT to TX, UOT to RX, RESET to GND, GPIO 0 to GND. But even if the computer sees the Arduino Uno card, it does not upload code. İt gives a "fetal error".
Yeah this error is common . There are many solutions for this . Try pressing enable button while uploading the code . Try using different USB port . Or cable . Check on internet for information on this error . It should be solved 👍🏻
@Alibali Alibeyov bro Iam also facing same issue. Did u solved it?
@@ameerpasha9941 yes I was able to solve. I just changed the port of the Arduino Uno card a few times, tried to reload and it worked. That's how I solved the problem. If you solve, you write the answer;)
@@alibalialibeyov3277 bro can i have ur mobile number
congratulations to the project, I just thought that the response time of the camera is much higher than the native webserver project, is there a way to make the camera refresh faster?
Thanks for checking out video 👍🏻 . Yeah camera image capture is faster however the transfer of image through Websocket limits the FPS for video . It’s the best I could do with this webserver . I would be glad if there is other way to improve it for more FPS. But for now don’t see any way to improve it further . The video is still responsive enough with VGA quality .
Use a pi zero w
I dont understand at 8:17 which pins do you connect in arduino uno?, and how it can connect to esp32-cam?
Please check the video slowly and also take a look at circuit diagram 👍🏻👏🏻
*HELP ME* sir 😭😭😭😭😭😭😭I can't access the IP address. What's the problem with the IP? Is it a bug/error?
Please check for loose connection. Provide proper 5 v supply only . 👍🏻👏🏻
I have a basic question.i m getting a esp32 board..... should i get the cam version or the plain esp32.....does the cam version have all the functionality of normal esp32...since number of pins in esp cam are half the number of non cam version
It depends upon your project need . Does your project need camera in it ? If yes then go for esp32cam . Else if you are starting with esp32 then buy simple esp32 module of 38 pins . Yes both the modules will almost function same with esp32 having far more number of pins than cam module.
Uploading the code from arduino uno to esp32 cam board is not working for me. It's saying failed to connect to the esp32 board and there is no serial data received.
Try to press enable button on that esp32 module 👍🏻👏🏻
Compilation error: 'ledcSetup' was not declared in this scope; did you mean 'ledc_stop'? plizzz
Please install 2.0.16 version of esp32 board 👍🏻👏🏻
@@hashincludeelectronics how bout the esp32servo?
@@athariksa6427 it’s same version 👍🏻👏🏻
@@hashincludeelectronics i used the version same as on the vid and it worked sir, thanks for you guide
A very nice project! I did it but only pan SERVO runs, Tilt SERVO not move, what can be? thanks.
Thanks . Please check the connections properly . May be there is loose connection for sure .
@@hashincludeelectronics thank you for quick reply , I did exchanged two SERVOs pin and tried all pins of ESP32CAM, only pin12 drived both SERVOS, other pin not...
@@baocunb770 you need to use io14 and io15 only .please check the circuit diagram for pins used .
Well sir if I use arduino nano here instead of arduino uno.....
Yes you can 👍🏻👏🏻
Hello! i get this error whenever i want to upload the code - A fatal error occurred: Failed to connect to ESP32: Timed out waiting for packet header. Can you help me please?
It’s very common error . You can find more details on this error on internet 👏🏻👍🏻
Hello, good video, where can I get the structure of the servos and the esp32cam camera?
Sorry I did not get your question.
can we use battery instead if then how???
Please check my other videos for reference 👍🏻👏🏻
I having an issue. Please help.
It's showing No such file or directory for esp_camera.h
What should I do?
Please check the video for installation of boards
Good day Sir, I faced a problem which is when I try to control my servo motor it will auto disconnected the wifi connection. Is it because of the current provided to the motor doesn't enough? But for the ESP32 CAM and the lightning control works well
Yes . Servo motors need proper current around 500 ma . So please use rechargeable battery and provide 5v to servos .
I see ... appreciate for the reply sir 🙇
@@Secret-eo1rz happy to help 👍🏻
Can we get images if ESP 32 is connected to the phone instead of connecting phone to ESP 32 ?
Sorry I did not get your question 👍🏻👏🏻
@@hashincludeelectronics i mean, can we use esp 32 cam station mode instead of setting it as access point ? (in your project phone connects to esp32 cam, but i want to connect esp32 cam to phone's hotspot)
@@psykopat81 yea you can . However what are you trying to achieve by doing this ? If you connect to your mobiles hotspot then you will have to get the ip address from esp32 which will be different.
@@hashincludeelectronics i am controlling my old android phone with teamviwer. If the esp32 cam is connected to the hotspot of this phone, I could control the esp 32 cam from anywhere in the world (you know blynk video streaming is now paid).
If the phone is connected to the esp32 cam via wifi, the mobile connection is automatically closed and I cannot connect to my old phone.
So the phone's mobile connection must remain open and esp32 must be connected to the phone.
Hi sir can you control by using MIT App inventor
App imventor should contain esp32 camera, pan and tilt controls,arrows for controlling car f,b,l,r
Plz make this for your new subscriber plzzzzzzzz😢😢😢😢😢😢
I have not used MIT app inventor yet . Will try it 👍🏻👏🏻
Please help..
When I uploaded the code after doing connection properly it was working properly. So I have disconnected the supply and I was happy. But after some time I again connected the supply and the problem starts from here. At first when I was trying to connect the wifi it connects and getting disconnected quickly. But now no hotspot is coming from the esp32 cam module as I can't see from the wifi section of my phone. So I have reset the board and uploaded the code again but still same problem.
Please give me the solution.
What power supply are you using ?