Thanks for the video! I also own a bx23s and have the bxpanded thumb and it’s been awesome. If you have a lot of stumps to remove I highly recommend the bxpanded root ripper. You have to make sure you have the bxpanded quick change kit installed to use it. Ive removed a lot of small and medium sized stumps and that root ripper saves a lot of time and doesn’t tear up as much dirt
Paolo... The quick hitch attaches to your three point hitch. It allows you to quickly attach and detach your implements without getting off the tractor. Just back up with the quick hitch under the pins on your implement, lift it up, and there are two levers that lock it in. Of course if you have a brush hog or tiller you will have to get off and hook up the driveline. It's pretty handy
You`ve got that pin installed wrong on your inner 3pt hitch plate. The bigger end of the pin should be riding against the cross shaft. The hair pin clip should be facing upward on top of the plate. I would advise fixing it the right way as soon as possible. If you don`t, that plate will move around a lot and cause you severe wear and binding issues. Not to mention, that cross shaft can knock that hair pin clip out pretty quick.
Yes sir, I certainly do. Thanks for pointing that out. I’ve since had that thing off numerous times switching between the hoe and the 3 point attachments and I may be getting the hang of it.
I feel like my bx23 doesn’t have enough power. I don’t feel like I’m over stressing it. I’m a newbie. Any tips when trying to lift with your loader? I was trying to lift some cut wood blanks. They definitely didn’t way more than capacity. My tractor has 44 hours on it
Keep your rpm’s up, if it’s close to the weight capacity be sure and keep your lift point as close to you (toward tractor) as possible and use the curl function. Other than that you might check your hydraulic pump psi. They sell kits with everything you need to check it as well as shims to add if it is too low
@@spineguy1553 DON`T go over 2000psi when you add the shims !!! Make sure you buy the hydraulic gauge to check that pressure at full throttle. Don`t just throw shims in it and call it good without knowing what the pressure is set at. And don`t expect Kubota to warranty ANYTHING if you do this shim kit on your tractor either. Because they won`t.
Thanks for the video! I also own a bx23s and have the bxpanded thumb and it’s been awesome. If you have a lot of stumps to remove I highly recommend the bxpanded root ripper. You have to make sure you have the bxpanded quick change kit installed to use it. Ive removed a lot of small and medium sized stumps and that root ripper saves a lot of time and doesn’t tear up as much dirt
Paolo... The quick hitch attaches to your three point hitch. It allows you to quickly attach and detach your implements without getting off the tractor. Just back up with the quick hitch under the pins on your implement, lift it up, and there are two levers that lock it in. Of course if you have a brush hog or tiller you will have to get off and hook up the driveline. It's pretty handy
Thank you for your video. I think your ideas are very good 👍👍🇺🇸
Sweet mods! I have my eye on that thumb! Its got to be super handy! Subscribed!
You`ve got that pin installed wrong on your inner 3pt hitch plate. The bigger end of the pin should be riding against the cross shaft.
The hair pin clip should be facing upward on top of the plate. I would advise fixing it the right way as soon as possible.
If you don`t, that plate will move around a lot and cause you severe wear and binding issues. Not to mention, that cross shaft can knock that hair pin clip out pretty quick.
Yes sir, I certainly do. Thanks for pointing that out. I’ve since had that thing off numerous times switching between the hoe and the 3 point attachments and I may be getting the hang of it.
Nice , I just got mine like yours, hopefully I can afford later to do some add ons like you
Did you fart @ 5:14?? 😂
Haha……sure sounds like it
Yep he ripped a nice one.
Well now. Must be that "global warming" thang 🔥🌡️ 😂😂😂
I feel like my bx23 doesn’t have enough power. I don’t feel like I’m over stressing it. I’m a newbie. Any tips when trying to lift with your loader? I was trying to lift some cut wood blanks. They definitely didn’t way more than capacity. My tractor has 44 hours on it
Keep your rpm’s up, if it’s close to the weight capacity be sure and keep your lift point as close to you (toward tractor) as possible and use the curl function. Other than that you might check your hydraulic pump psi. They sell kits with everything you need to check it as well as shims to add if it is too low
Thanks for the reply. Much appreciated! I ordered the shim kit.
@@spineguy1553 DON`T go over 2000psi when you add the shims !!! Make sure you buy the hydraulic gauge to check that pressure at full throttle. Don`t just throw shims in it and call it good without knowing what the pressure is set at. And don`t expect Kubota to warranty ANYTHING if you do this shim kit on your tractor either. Because they won`t.
What trickle charger mount did you use? I can’t find one to mount on the tractor
I used the battery minder EZC-01 universal flush-mountable EZ connector with 4 mounting screws
$17.99 on Amazon
When you buy a trickle charger, DON`T use any more than a 1.25 volt trickle charger. Anything higher will boil the battery and ruin it.