the code is a 3 digit number between 001 to 999. Try 001 For Level 1 access. Try 017 for Level 2 Access. Try 990 for Level 3 / All access. if None of those codes work it is a Hit & miss deal trying to Hack the passcode. it takes me about an hour or two to hack one of those danfoss temperature controls. i usually remove the controller and bring it back home , crack a beer and start punching in different codes. ill install a used temperature control to get them by till i hack the code. or u can allways just buy a new control and install it. them come new with 000 as the New code. when u push in a New code hit the enter button which is the Lower left button to enter code. 3 incorrect attempts and the controller will lock u out for 5 minutes. then u have to power down the controller / unplug the refrigerator from the wall to bypass the lock out or wait 5 minutes. i use a Power strip at home with a switch on it & a 115 volt pigtail when cracking codes at home.i put push on connectors on the end of the pigtail cord to plug it into the Danfoss controller. Good Luck ! Your Gonna need it.
Thanks for the Heads up on the Dixell. I have not seen (that i can recall) a dixell control on anything i work on. I am just starting to see Alottt of Digitals breaking & on new equiptment. I see alot of Carell controllers on the China , korean throw away fridges. And Alott of Emerson on Copeland New Equiptment of course.
Been doing this 36 years , dont think i ever seen a " Franke " unit. it just proves you can do this a long time and still see new stuff. Man , this trade is vast.
Hi Oc. Thank you for the video. I am new to the refrigeration. Could you advise why reach in coolers and undercounter coolers use coil sensing thermostats while many others like display coolers or walkin coolers use air sensing thermostats? Why not mount sensors to the coils as in reach in coolers? One customer had frozen display cooler (fans running, evap coil is clean) with timed defrost. With timed defrost I will either over defrost it or underdefrost it but if I mount the sensor on the coil with 35-36 cutin. What can go wrong? Thank you.
Yes , You are correct everything would be better if Evaporator temperature sensing was used everywhere. i don't know why it's not done. You can do it on everything. cut in at 39. cut out at what ever evap temperature is required for 35 degrees. it can be as low as 11 degrees on some units. its definitely a better way to go in my opinion too. no defrost clock needed. better temperature control. Probably not done because it's just easier to set a control to 35 and walk away. Other way you have to stay and find the Evaporator temp that = 35 degrees then set control at that. or You can just start with 25 degrees and see what box temp is then subtract 1 degree for every degree cooler u want the box. Prep. tables have to do it the better way because thier is so much air infiltration from many door openings & open top with containers.
What does it mean if “non” notification on the display is shown constantly? The controller will display “non” if the temperature sensor to display is not configured under SxC and SxA. For example, if the temperature to display (trS) is selected as “SCO” and if SCO is not configured to any of the inputs (S1, S2,..S4), the controller will display “non”. Also if SCO is configured, but the input configuration (SxC) is not selected correctly for that input, the same error message will be displayed. You need to ensure that the selected display sensor is correctly configured under input configuration and input application in the assignment menu group. www.danfoss.com/en/service-and-support/fix-and-troubleshooting/cooling-installer-hub/electronic-controllers-services-faqs/commercial-refrigeration-controllers-faq/#:~:text=What%20does%20it%20mean%20if,(S1%2C%20S2%2C..
Thanks for sharing, does anyone know the schematics to the COMM Di port? i would like to interface to this controller using an MCU to read of the temperature ... anyone please....??
Thanks for the info. Ill check into the eliwell controller and see if its available or used out here in California. I am starting to see Alottt of Different digital controllers out here in California now. Thier are Alott of different ones out here Carell , Danfoss , Emerson. What state or country are You in ?
OcRefrigeration,Hvac & Electrical. Europe Holland. The top 5 used here is eliwell, danfoss ,dixxel,elreha, and last the carel,s. They have the easy series these are very competetive and they usually need no altering of the parameters.
Southern California here. Thanks for reply. Seeing alott of Carels now , Danfoss Second & Emersons on All Copeland indoor condensing units. No eliwells yet. No elreha. I guess dixell & emerson are same people now here.
Hi Sjef, that is actually not accurate. The ERC101 and the 111 use as default NTC sensors. PTC are an option for applications that requires them. See the information available here on the range of sensors: products.danfoss.com/productrange/list/refrigeration/electronic-controls/electronic-refrigeration-temperature-controls/electronic-temperature-controls-accessories-and-spare-parts/erc-accesories-and-spare-parts/#/ Please do not hesitate to reach out for information on contacts and where to find the products in your area.
the code is a 3 digit number between 001 to 999. Try 001 For Level 1 access. Try 017 for Level 2 Access. Try 990 for Level 3 / All access. if None of those codes work it is a Hit & miss deal trying to Hack the passcode. it takes me about an hour or two to hack one of those danfoss temperature controls. i usually remove the controller and bring it back home , crack a beer and start punching in different codes. ill install a used temperature control to get them by till i hack the code. or u can allways just buy a new control and install it. them come new with 000 as the New code. when u push in a New code hit the enter button which is the Lower left button to enter code. 3 incorrect attempts and the controller will lock u out for 5 minutes. then u have to power down the controller / unplug the refrigerator from the wall to bypass the lock out or wait 5 minutes. i use a Power strip at home with a switch on it & a 115 volt pigtail when cracking codes at home.i put push on connectors on the end of the pigtail cord to plug it into the Danfoss controller. Good Luck ! Your Gonna need it.
This might be it. www.walmart.com/ip/Connector-For-Electronic-Control-Danfoss-Erc-080g3365/936678951?wmlspartner=wlpa&selectedSellerId=101002108&&adid=22222222228392642048&wl0=&wl1=g&wl2=m&wl3=481578285802&wl4=pla-1223646316992&wl5=9031534&wl6=&wl7=&wl8=&wl9=pla&wl10=128898301&wl11=online&wl12=936678951&veh=sem&gclid=EAIaIQobChMIqITP56-I8AIV8AytBh12NwOCEAQYASABEgL-zfD_BwE&gclsrc=aw.ds
I Have not bought them before. I just use Female push on connectors. They are the same size. www.amazon.com/Yueton-100pcs-Insulated-Terminal-Connectors/dp/B010GWZOUW/ref=asc_df_B010GWZOUW/?tag=hyprod-20&linkCode=df0&hvadid=198055979756&hvpos=&hvnetw=g&hvrand=1372867750814901230&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9031534&hvtargid=pla-391793085094&psc=1
You are probably calling them after working hours. I think they are in Denmark. So , try calling during business hours danish time. They are 9 hrs ahead of California time. 11pm California = 8am Denmark.
Hey there, maybe you will be able to help me... i have a danfoss erc112 controller. now for some reason when i try to press up+down arrows i can not enter the menu and PAS does not show. is it maybe locked? is there a way to factory reset the controller? any help would be appreciated. cheers.
OcRefrigeration,Hvac & Electrical. Thanks, already did. My controller is locked by the manufacturer of the freezer and can only be reflashed via usb stick. I just replaced it with another one. Cheers.
Please help on how set the temperature as my controller stay on 23cel. It won't change if I did. Please help me, your video was helpful but I can figure it out
1) Hit arrow buttons up or down to desired set temperature. ( upper right button - to increase temperature ) ( Lower Right Button to Decrease temperature ) 2) Then hit Power button ( Lower Left Button ) immediately which will Set the New Temperature inside the control. The Power Button is also known as the " Set button or " Ok " Button. Watch video again , it is very well explained.
Hey im having a problem and maybe you can help me, on the controller the temperature is diferent than the one inside the fridge, there is any way to calibrate the controller temperature to match it to the one inside the fridge, thanks in advance.
First --- Figure out which temperature is correct. Second --- if the danfoss digital is off. Replace the thermistor. remember the controller may be sensing evaporator temperature not box temperature.
No. you will adjust the offset u want. if the display is reading 32 and u want it to say 34. you would " up arrow " + 2.0 degrees. You can offset 18 degrees in either direction to allow for calibration of thermistor.
no default settings. No reset. must be programmed one by one. the Passcode is a 3 digit number between 001 to 999. Try 001 For Level 1 access. Try 017 for Level 2 Access. Try 990 for Level 3 / All access. if None of those codes work it is a Hit & miss deal trying to Hack the passcode. it takes me about an hour or two to hack one of those danfoss temperature controls. i usually remove the controller and bring it back home , crack a beer and start punching in different codes. ill install a used temperature control to get them by till i hack the code. or u can allways just buy a new control and install it. them come new with 000 as the New code. when u push in a New code hit the enter button which is the Lower left button to enter code. 3 incorrect attempts and the controller will lock u out for 5 minutes. then u have to power down the controller / unplug the refrigerator from the wall to bypass the lock out or wait 5 minutes. i use a Power strip at home with a switch on it & a 115 volt pigtail when cracking codes at home.i put push on connectors on the end of the pigtail cord to plug it into the Danfoss controller. Good Luck ! Your Gonna need it.
Password?!?
the code is a 3 digit number between 001 to 999. Try 001
For Level 1 access. Try 017 for Level 2 Access. Try 990 for Level 3 / All access. if None of those codes work it is a Hit & miss deal trying to Hack the passcode. it takes me about an hour or two to hack one of those danfoss temperature controls. i usually remove the controller and bring it back home , crack a beer and start punching in different codes. ill install a used temperature control to get them by till i hack the code. or u can allways just buy a new control and install it. them come new with 000 as the New code. when u push in a New code hit the enter button which is the Lower left button to enter code. 3 incorrect attempts and the controller will lock u out for 5 minutes. then u have to power down the controller / unplug the refrigerator from the wall to bypass the lock out or wait 5 minutes. i use a Power strip at home with a switch on it & a 115 volt pigtail when cracking codes at home.i put push on connectors on the end of the pigtail cord to plug it into the Danfoss controller. Good Luck ! Your Gonna need it.
What do you need the passcode for ?
@@OcRefrig got it, its 17
@@OcRefrig to service, thanks.
My rhino bar fridge. Took me two beers.
Ps1: 111
Ps2: 147
PS3: 258
holy cow u lost me at hello, but very detailed, u put alot of work into this
👍
the danfoss control is nice better than dixill. thanks for the walk through!
Thanks for the Heads up on the Dixell. I have not seen (that i can recall) a dixell control on anything i work on. I am just starting to see Alottt of Digitals breaking & on new equiptment. I see alot of Carell controllers on the China , korean throw away fridges. And Alott of Emerson on Copeland New Equiptment of course.
Another great video. Thanks for the detailed information.
Your welcome.
I am familiar with the Dixell controllers that look like that. Thanks for the video OC.
Your Welcome ! who uses dixell ?
Franke reachin coolers and freezers. They were a popular product line in Mcdonalds restaurants I used to service.
Been doing this 36 years , dont think i ever seen a " Franke " unit. it just proves you can do this a long time and still see new stuff. Man , this trade is vast.
Fantastic job OC 👍👍
Thanks H. 👍😎🏝
Hi Oc. Thank you for the video. I am new to the refrigeration. Could you advise why reach in coolers and undercounter coolers use coil sensing thermostats while many others like display coolers or walkin coolers use air sensing thermostats? Why not mount sensors to the coils as in reach in coolers? One customer had frozen display cooler (fans running, evap coil is clean) with timed defrost. With timed defrost I will either over defrost it or underdefrost it but if I mount the sensor on the coil with 35-36 cutin. What can go wrong? Thank you.
Yes , You are correct everything would be better if Evaporator temperature sensing was used everywhere. i don't know why it's not done.
You can do it on everything. cut in at 39.
cut out at what ever evap temperature is required for 35 degrees. it can be as low as 11 degrees on some units. its definitely a better way to go in my opinion too. no defrost clock needed. better temperature control.
Probably not done because it's just easier to set a control to 35 and walk away. Other way you have to stay and find the Evaporator temp that = 35 degrees then set control at that. or You can just start with 25 degrees and see what box temp is then subtract 1 degree for every degree cooler u want the box.
Prep. tables have to do it the better way because thier is so much air infiltration from many door openings & open top with containers.
@@OcRefrig Thank you very much for the great explanation 🙏
Nice, keep up the good work
Thanks.
Hi, İ have a problem with danfoss 112C. On display shows NON and compressor don't active anymore
What does it mean if “non” notification on the display is shown constantly?
The controller will display “non” if the temperature sensor to display is not configured under SxC and SxA. For example, if the temperature to display (trS) is selected as “SCO” and if SCO is not configured to any of the inputs (S1, S2,..S4), the controller will display “non”. Also if SCO is configured, but the input configuration (SxC) is not selected correctly for that input, the same error message will be displayed. You need to ensure that the selected display sensor is correctly configured under input configuration and input application in the assignment menu group.
www.danfoss.com/en/service-and-support/fix-and-troubleshooting/cooling-installer-hub/electronic-controllers-services-faqs/commercial-refrigeration-controllers-faq/#:~:text=What%20does%20it%20mean%20if,(S1%2C%20S2%2C..
Hi, I have erc111a thermostat and I can’t set it at 0 degree. It won’t go below 27 degrees.
Thanks for sharing, does anyone know the schematics to the COMM Di port? i would like to interface to this controller using an MCU to read of the temperature ... anyone please....??
i don't believe that's possible. its only a point of connection for door switches & light sensors and such.
Hi, My name suhendrik. I'm from Indonesia. May I ask manual book for this type Temperature Control. Thanks for your help brother.
assets.danfoss.com/documents/55644/BC200686422115en-000102.pdf
👍
👍😎🏝
Nice controller, but the sensors are expensive pt 1000, the eliwell controler has an easyer menu and sensors are cheaper standard ntc.
Thanks for the info. Ill check into the eliwell controller and see if its available or used out here in California. I am starting to see Alottt of Different digital controllers out here in California now. Thier are Alott of different ones out here Carell , Danfoss , Emerson. What state or country are You in ?
I have not had any bad sensors yet or priced them out for availability. Thanks for the heads up on the price.
OcRefrigeration,Hvac & Electrical. Europe Holland. The top 5 used here is eliwell, danfoss ,dixxel,elreha, and last the carel,s. They have the easy series these are very competetive and they usually need no altering of the parameters.
Southern California here. Thanks for reply. Seeing alott of Carels now , Danfoss Second & Emersons on All Copeland indoor condensing units. No eliwells yet. No elreha. I guess dixell & emerson are same people now here.
Hi Sjef, that is actually not accurate. The ERC101 and the 111 use as default NTC sensors. PTC are an option for applications that requires them. See the information available here on the range of sensors:
products.danfoss.com/productrange/list/refrigeration/electronic-controls/electronic-refrigeration-temperature-controls/electronic-temperature-controls-accessories-and-spare-parts/erc-accesories-and-spare-parts/#/
Please do not hesitate to reach out for information on contacts and where to find the products in your area.
Hi. what is the PAS of this controller to enter its configuration? Mod. 112D
the code is a 3 digit number between 001 to 999. Try 001
For Level 1 access. Try 017 for Level 2 Access. Try 990 for Level 3 / All access. if None of those codes work it is a Hit & miss deal trying to Hack the passcode. it takes me about an hour or two to hack one of those danfoss temperature controls. i usually remove the controller and bring it back home , crack a beer and start punching in different codes. ill install a used temperature control to get them by till i hack the code. or u can allways just buy a new control and install it. them come new with 000 as the New code. when u push in a New code hit the enter button which is the Lower left button to enter code. 3 incorrect attempts and the controller will lock u out for 5 minutes. then u have to power down the controller / unplug the refrigerator from the wall to bypass the lock out or wait 5 minutes. i use a Power strip at home with a switch on it & a 115 volt pigtail when cracking codes at home.i put push on connectors on the end of the pigtail cord to plug it into the Danfoss controller. Good Luck ! Your Gonna need it.
Please where can I get this document. Thank you
assets.danfoss.com/documents/55644/BC200686422115en-000102.pdf
www.rathvac.com/wp-content/uploads/2014/11/Danfoss-erc-101-instruction.pdf
Hey do they sell the connections that goes on the back of that controller ?
This might be it. www.walmart.com/ip/Connector-For-Electronic-Control-Danfoss-Erc-080g3365/936678951?wmlspartner=wlpa&selectedSellerId=101002108&&adid=22222222228392642048&wl0=&wl1=g&wl2=m&wl3=481578285802&wl4=pla-1223646316992&wl5=9031534&wl6=&wl7=&wl8=&wl9=pla&wl10=128898301&wl11=online&wl12=936678951&veh=sem&gclid=EAIaIQobChMIqITP56-I8AIV8AytBh12NwOCEAQYASABEgL-zfD_BwE&gclsrc=aw.ds
I Have not bought them before. I just use Female push on connectors. They are the same size.
www.amazon.com/Yueton-100pcs-Insulated-Terminal-Connectors/dp/B010GWZOUW/ref=asc_df_B010GWZOUW/?tag=hyprod-20&linkCode=df0&hvadid=198055979756&hvpos=&hvnetw=g&hvrand=1372867750814901230&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9031534&hvtargid=pla-391793085094&psc=1
When I come in the morning the ECO light comes on and the temperature is above 40 F needs to be between 34 and 40. How would I fix this?
Call Danfoss at 1-888-Danfoss.
1-888-326-3677 and they can Walk u thru the steps.
@@OcRefrig thank you
Hmm keep getting Fax Machine sound when i call.
You are probably calling them after working hours. I think they are in Denmark. So , try calling during business hours danish time. They are 9 hrs ahead of California time. 11pm California = 8am Denmark.
Hey there, maybe you will be able to help me... i have a danfoss erc112 controller. now for some reason when i try to press up+down arrows i can not enter the menu and PAS does not show. is it maybe locked? is there a way to factory reset the controller? any help would be appreciated. cheers.
yes, locked. contact danfoss or manufacturer of refrigeration equiptm,ent and ask for password.
OcRefrigeration,Hvac & Electrical. Thanks, already did. My controller is locked by the manufacturer of the freezer and can only be reflashed via usb stick. I just replaced it with another one. Cheers.
Please help on how set the temperature as my controller stay on 23cel. It won't change if I did. Please help me, your video was helpful but I can figure it out
1) Hit arrow buttons up or down to desired set temperature. ( upper right button - to increase temperature ) ( Lower Right Button to Decrease temperature )
2) Then hit Power button ( Lower Left Button ) immediately which will Set the New Temperature inside the control. The Power Button is also known as the " Set button or " Ok " Button.
Watch video again , it is very well explained.
Thanks man, you are great
Hey im having a problem and maybe you can help me, on the controller the temperature is diferent than the one inside the fridge, there is any way to calibrate the controller temperature to match it to the one inside the fridge, thanks in advance.
First --- Figure out which temperature is correct.
Second --- if the danfoss digital is off. Replace the thermistor. remember the controller may be sensing evaporator temperature not box temperature.
@@OcRefrig ok the thermostat is sensing 32F and inside is at 39F, so there is any way to adjust that difference??? the correct temperature is 34F
Yes. you can change " the display offset " " Dof " under display in the controller.
@@OcRefrig so I just enter to DoF and adjust the temperature with the one inside?
No. you will adjust the offset u want. if the display is reading 32 and u want it to say 34. you would " up arrow " + 2.0 degrees. You can offset 18 degrees in either direction to allow for calibration of thermistor.
Where I buy Danfoss ERC 111a controller
Please give me contact details
Can I use this same set up on a redbull fridge
sure.
Podrias subirlo en español ..??
I’ll work on it.
Sir how to reset default setting
no default settings reset. must be done one by one.
Hello there, how do default the settings one by one... Thank in advance..
how to reset pasword in ERC 101A (080G3132)
no default settings. No reset. must be programmed one by one.
the Passcode is a 3 digit number between 001 to 999. Try 001
For Level 1 access. Try 017 for Level 2 Access. Try 990 for Level 3 / All access. if None of those codes work it is a Hit & miss deal trying to Hack the passcode. it takes me about an hour or two to hack one of those danfoss temperature controls. i usually remove the controller and bring it back home , crack a beer and start punching in different codes. ill install a used temperature control to get them by till i hack the code. or u can allways just buy a new control and install it. them come new with 000 as the New code. when u push in a New code hit the enter button which is the Lower left button to enter code. 3 incorrect attempts and the controller will lock u out for 5 minutes. then u have to power down the controller / unplug the refrigerator from the wall to bypass the lock out or wait 5 minutes. i use a Power strip at home with a switch on it & a 115 volt pigtail when cracking codes at home.i put push on connectors on the end of the pigtail cord to plug it into the Danfoss controller. Good Luck ! Your Gonna need it.
if u can't figure out the passcode just buy
a New controller. New controller comes set with no passcode.
Какой пароль для входа в меню?
you have to call the manufacturer of your equiptment ask them for the code.