The Beginning Of My G SPEED FS BUILD | MAILTIME!
Vložit
- čas přidán 7. 08. 2024
- I'm getting into this G Speed FS build and I might need your help plus a quick Mailtime with the Rino 1800kv motor and ESC
If you would like to help support the channel you can use the affiliate links below at no extra cost to you and we will receive a small commission.
110MM Desert Lizards:
www.amazon.com/dp/B07N8GD2H3/...
Injora Portal Axles:
amzn.to/4bBMwlK
Flash Hobby Servo:
amzn.to/3zv7HJ8
Servo Horn:
www.amazon.com/dp/B083Y352G7/...
BFG Krawler Predator Compound Tires:
amzn.to/3zwfMgy
Vintage Aluminum Wheels:
amzn.to/4cSico1
MAILTIME ITEMS
Rhino ESC 80 amp:
amzn.to/3xR4WBf
Rhino 1800kv Outrunner:
amzn.to/4byxHAE
Fairlead:
amzn.to/4bENn5c
#rccrawler #gspeedchassis
7-8-24
Get rid of those front link! You'll be hung up on the skid all the time. You want to be able to slide on your front links. Back may be ok, but you can get some shorter rod ends for the uppers and longer for the lowers to change pinion angle. The shorter the shock, the lower the gravity center.
Yes sir, thank you. I hate the links area lol, I will see what I can do in the meantime. I'm so excited, I've got a new winch!!
Can't wait for the AM32 review😊
ME EITHER!
First will be an initial impressions, thanks man
I like everyone's helpful comments. Front lower links are bent way too much, I noticed your drag link's kinda hanging, try shooting for a hole closer to the servo on that long horn, ideally you want your drag link at 90°. Rear pinion angle is extreme, try setting your axle without wheels so that it sits on the portal boxes and layout your links from there. Keep up the good work.
Thanks brother, hope you watch vid 2. 👍🏻
Great build! I run 80mm lizards in the front (full bump), and 2660 in the rear with the rear mini-t springs in soft. You don't want a ton of articulation as it will make your truck extremely unpredictable. I've spent a very long time trying different combos, and this two shock setups have proven to work the best for my style of driving.
Awesome to know, thanks for the input and I hope it's not too much articulation. Imma see were this build brings me and I hope it crawls good!
@@arkansasrcnewbie good luck sir! 🍻
Hi. Here is a lot to Diskussion.
1. Portal axles: yes
2. Rear shocks should be layed down to 45 or 50 degrees. Gives more articulation, which is a good thing
3. Front lower links has to be straight and perhaps shortened
4. Wheelbase recommend from 12.3 to 12.5" to your liking (dont know if rules class2 oppose)
5. Rear pinion of axle should be less angled up. Yet a little bit up is good for clearance
6. Servo horn should be shorter. Try a bent steering link. Better would be a servo on axle anyways
7. Rhino esc and motor are great
Keep it up🥳
Man! Thank you for the write up!!
I appreciate that very much, got the axle straight now in the rear.
I may switch to my 90mm lizards and angle them more as well. Thank you!
Definitly the 90 mm lizards!
I'm only 3:41 in, so i could be commenting on something your gonna mention but i do notice that you've got a 3 link in the front but have a SOA setup, i believe 4link for SOA and 3 for CMS. anyways i don't know what i'm talking bout' thank you for the videos between bikes and RC's!
OH SHOOT I'M DUMB!! It looks SOA but i see what you did, haahaa sorry! excited for this build my guy!
🤣 Love it that you watched all the way thru and kept pne continous comment lol.
Thanks for the looking out brother, I have no clue what I'm talking about either!!
Articulation is good. There is a point where it’s too much but for the most part it is definitely good to have.
Something you might want to try is some DEEZ shock bands to help keep your shocks from unloading when you don’t want them to if you’re not going to use the Desert Lizards.
I’ve tried G-speed a couple times now and both times I ended up replacing them. Almost any other chassis will offer far more for tuning, shock mounting positions, and customization over G-speed. I’ve had the best results with either Spare Time Hobbies or Corrupt Carbon Works.
Awesome info! Thank you so much, I really need a test and tune day. Like bad!! Appreciate the comment
I also run the desert lizard 120mm but I found that I get more articulation when my shocks upside down. I realize it brings the center of gravity up a bit but I'm for more articulation. And I think the pinion needs to be at a lot less of an angle. Very good start.
Thanks brother, I was just about to switch to the 80s lol
We will see with time, thanks for the heads up
Bottom links up front need to be flipped or straight & shorter in my opinion. WB is great.
SOA is much better then 3link. Flex is great if it’s manageable
Awesome! Thank you, I'll se how I like the WB and hopefully it will workout OK. Appreciate the help
Nice 👍🏾🔥
Thanks man, super excited!
As far as shocks go i stick too around 80 to 85mm shocks but i also run a king of the south chassis so you can be slammed and still have more clearance over any chassis.
Nice man, thanks! I've got some 80 or 85mm lizards I just might install.
@@arkansasrcnewbie yes sir give them a shot and see what you prefer.
I prefer my wb around 12.5 thats just what i got used to driving.
I'm hoping 13 will be fine, I know I don't wanna mess with links anymore!
@@arkansasrcnewbie yeah links are a bit of a pain but when you get them right they will be on point.
I built a gs fs gshot but I went with f10 straight axles...had to order different front upper links but it will climb the wall.
Everyone's saying upper links, I may have an issue there....thanks for the comment man.
You're a dip switch! 🤣 I believe the key for your links is to make sure they won't get caught up on rocks and such but I only crawl over rocks in my yard so...
you better get to building if your comp is in a week!!
I am for sure!
Man I'm learning Slothsquatch 🤣 it is looking dope!
@@arkansasrcnewbie that what matters the most, always learning and improving!
That a brake line bender you're using to bend links?
Lol, yes mini tube bender
@@arkansasrcnewbie work decent for bending links?
The front links should be shorter and that would have got it at just under 12.5 wheelbase. Give me a measurement for those front lowers and ill see what i have so you can use straight lowers. Those are going to hang up.
Well that would be appreciated, thank you so much. Let me check it out tonight!
Well I measured 4-1/4" eyelit to eyelit maybe a tiny bit more/less. Thank you once again
@@arkansasrcnewbie you going to the comp tomorrow?
czcams.com/video/CH8heFQ3G-w/video.htmlsi=W2_AIx7sfX46XScS
This is another video that helped me install firmware and flash the rhino esc to make adjustments hope it helps
Thanks brother, that's gonna be the next question!!! 💪 Thanks
czcams.com/video/0WmpVvyTt8M/video.htmlfeature=shared
This guy has been killing it with his videos on the geometry of the matter. Im sure you will have it all dialed in real soon. Looking forward to the new rig and learning from your mistakes along the way! Lol
Thanks brother, ill be checking it out lol.
It's definitely a trial and error.
Get shorter shocks bro. 90mm ideal. 100mm at most
Well I do have some 90mm Lizards.....