GMC Acadia 2007 to 2015 replacing belt and belt tensioner // belt broke truck over heats
Vložit
- čas přidán 24. 08. 2024
- Due to factors beyond the control of RB The Mechanic, it cannot guarantee against unauthorized modifications of this information. RB The Mechanic assumes no liability for property damages or injury incurred as a result of any of the information contained in this video. RB The Mechanic recommends to follow safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, chemicals, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of RB The Mechanic, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not RB The Mechanic.
RB The Mechanic. All rights reserved. Publication, reproduction or distribution of this or any video by any means whatsoever, including without limitation electronic transmission via internet or e-mail, or re-uploading existing videos & re-uploading such material on any website anywhere in the world, is strictly prohibited without the prior written consent of RB The Mechanic.
#gmc #acadia #gmcacadiabelt #belttensioner #gmcacadiabelttensioner #belttensionergmcacadia #2012gmcacadiabeltbroke #2012gmcacadiabelttensnorbrole #gmcacadiabeltdiagram
Just seeing the belt configuration helped. Thanks . The acadia is the hardest vehicle ive ever worked on not much space and alot of removal to get to anything.
Yeah I did video on the idler pully and tensnor it was crazy tight
On an Equinox, can you just remove the air cleaner and motor mount to access the idler pulley bolt?
Pisses me off, I had a new tensioner and pulley in the parts box when the shop had the engine out to do the timing chains and head rework. Went in the “used” parts box (always request your old parts back) and here was the new tensioner and pulley! At least he installed the new belt…
I’m not sure how the setup is on equinox however this gmc Acadia there was no way even if u remove mount and jack up
Yeah...I'm just mad because I provided the parts as I knew this was a 3 minute job while the engine was out of the car!!!
شكرآ لقد استفدة
English bro
So to replace the idler pulley you have to jack up the engine?
Yup and remove the fuse box and remove the engine mount it’s a mess I did able to get the bolt out for what I show manually slowely
The official way to do it is to remove the fuse box and engine mount under the fusebox from the top then remove all bolts for the alternator and you can then get the bolt for the idler out. no need to lift the engine it all. besides removing and installing the belt, all the work is done from the top.
@@northern3000aye my boi that u soo much frfr men 💯
Is there any sort of splash shield to protect the belt from splashes? Or did GM just leave it open to the world?
My friends belt is slipping when he drives over puddles; I'm going to change the belt but I'm not sure if there's supposed to be a splash shield too...
Yeah it’s just open I didn’t notice any covers
It's open. If it's slipping the belts dry or tensioner is worn. The belt getting wet on these doesn't make it slip. Only thing I'd be worried about would be blasting through heavy heavy drifts and the snow knocking the belt off. But only a small area is exposed, and if you were that worried about it, you could pop rivet some straps of plastic (like from a Rubbermaid tote you find on the curb and slice up)
@@AMCtilldeath yeah open area
Did he just say get that center bolt off the alternator lol
Uhoh did I!? I would be stupid to say that
So, do i need to jack the engine 100% to do the job? Can i remove the headlight to do this? Or is there another way?
Nope this is the only way
@@RBTheMechanic now, do i use the list to Jack it up or lower it?
@@Rocksolid711 what?
Sorry, do i use a car jack to place the wood block to raise the engine a bit after undoing the engine mount or would i lower the engine to get the bolt out?
No, you don't need to jack the engine, you can just unscrew the alternator
So did it ran???
Uup
Easier to remove passenger headlight to get to bolts
Yeah but still the metal frame is issue
@@RBTheMechanic GM didn't put any thought in maintenance when they built these vehicles. To have to pull/jack up the motor to remove a bolt is asinine. I just did this on an Enclave and it was a PIA. I removed the rear bolt and center bolt then tilted the assembly up to get a wrench on the bolt to remove that one. Seriously ridiculous.
Who'd think to remove the headlight to replace a belt tensioner haha.
@@SWFabrication. I took out catalytic converter to replace starter on this gmc Acadia. That wicked and wild
@@RBTheMechanic what? that’s crazy, how long did it take to do that?
@@SWFabrication. 3 hours. Here the video czcams.com/video/ohDVaunwXLc/video.html
This video doesn't help. Can't hear half of what was said. This guy made me a good mechanic but the videographer he is not
lol ok
شكرآ لقد استفدة
English please
Sorry bro translation?
@@RBTheMechanicbasically they said thanks