How to Fix Samsung Washer OFF Balance | Shaking and Banging on Sides | Model
Vložit
- čas přidán 1. 08. 2023
- In this Video, We have a Samsung Top Load Washer, Model #WA54R7200AW/US, In Which the Complaint Was that it Sounded OFF Balance and it was Shaking as Well as Banging on Sides During the Spin Cycle. This is a Usual Indication that the Suspension Shocks Are Bad and Need to be Replaced. After Confirming that the Shocks indeed Needed to Be Replaced, We went ahead with the Repair. If Your Samsung Washer is Having this Same Symptoms, Make Sure to Watch the Entire Video to See How to Replace the Suspension Shocks on Your Washer Yourself and Save Some Money!
Please Like this Video, Share and Subscribe for Future DIY Videos. Support Our Channel by Using the Affiliate Links Below. If You Can, You may Also Leave a Tip Below. Thanks For Watching and for the Support.
Suspension Shocks (Set of 4, Aftermarket)
- Amazon: (These are the ones Used in this Video) amzn.to/3OEuGpZ
- eBay: ebay.us/qG8GBD
Suspension Rod (OEM, Single) : ebay.us/qSdwwM
If You'd Prefer an OEM Rod, You May Also Use RepairClinic.com. Have Your Model Number Ready and Click HERE ➡️ www.dpbolvw.net/click-1004923...
Other Items Mentioned:
- Phillips Screwdriver: amzn.to/3OERkyD
- Affordable Drill: amzn.to/45a2j8x
- Phillips Drill Bit Set: amzn.to/47evQjq
- Black Tape: amzn.to/3YpNwok
Videos Mentioned:
- Samsung Washer Banging on Sides: • How to Fix Samsung Top...
- Samsung Washer OFF Balance: • How to Fix Samsung Top...
- Samsung Washer OFF Balance: • How to Fix Samsung Top...
⭐️⭐️⭐️ Find Some of Our Faves on Our Amazon Storefront!! ➡️➡️ amzn.to/3xPs2rI⭐️⭐️⭐️
Sign up For a FREE 30-Day Trial of Amazon Prime and Get Your Appliance Going Faster! CLICK HERE: amzn.to/3BA7Erj
If this Video Helped you in any way, Consider Leaving a Tip:
- Buy Me a Coffee: buymeacoffee.com/diyrepairsnow
- PayPal: @diyrepairsnow
- Venmo: @diyrepairsnow
*Please note that Links are Affiliate Links, Which Means by Using them We do Get a Small Commission. This Means You Can Support the Channel at No Extra Expense to you. Thank you for your Support.
Warning: Please Be sure to Unplug Any Appliance Before Starting any Repairs! This video is to help DIY's do the repairs themselves, at their own risk. DIY Repairs Now, Its Technicians and/or Its Affiliates are NOT Responsible for Any Property and/or Personal Damages, Including Serious Injury and/or Death. Please Be Advised, as You have Been Warned.
My Filming Equipment:
Canon M50: amzn.to/2WUHlY5
Rode VideoMicro Compact Mic: amzn.to/2TqKTzo
Canon M50 Mount Adapter: amzn.to/2MZv84t
Joby GorillaPod 3K: amzn.to/2Fn3jgd
GoPro Hero 7 Silver: amzn.to/2UNHImN
GoPro Hero 7 Black: amzn.to/2TnPXVd
GoPro Accessories Kit: amzn.to/2OnilpG
For Business Inquiries, Please Email diyrepairsnow@yahoo.com
Thanks for Watching and be Sure to Subscribe for more HowTO/Repair Videos!
- DIY Repairs Now
#appliancerepair #appliance #appliances #kitchenappliances #homeappliances #repair #dishwasher #kitchen #refrigerator #home #fridge #refrigeratorrepair #oven #washerrepair #homeappliance #authorized #washingmachine #dryer #ovenrepair #service #stove #freezerrepair #dishwasherrepair #maintenance #washer #kitchendesign #dryerrepair #stoverepair #applianceparts #bhfyp - Jak na to + styl
Thank you so much for this! My husband is a good handyman but not a washing machine repairman. He watched your video, ordered the part from Amazon, and then used your video as a guide. Washer is now working great. No more off balance. So thank you!!!
I am Happy to hear My Video Helped Your Husband Fix Your Washer! 👍🏻👍🏻 Thanks For Watching!
I used your video and replaced the stabilizer rods in my Samsung washing machine with the help of my daughter. Somethings were a little different but we figured them out. Thank you for the tip on taking pictures before taking things apart. That was a life saver. My washer works like a charm again. I am a single mom and you saved me a lot of money. ❤
Did you have the same washing machine? I have the same exact one and I need to do something because it's constantly off balance now 😢
You’re welcome thanks for watching my video👍🏻👍🏻💯💯
How much did it cost to replace them
@@afterthought72 $45 Amazon. Parts in 2 days.
I followed your instructions and installed the new shocks in about an hour in total. Working great now and now I know how to do this. I looked at five other videos and yours was the most accurate and helpful. Thank you!
You’re welcome thanks for watching my video💯💯👍🏻👍🏻
Thank you for this video. You are a great teacher! We ordered the parts today!
Best walkthrough DIY repair YT video I've seen in a very long time. Simple to follow, excellent. Thanks!
Glad you liked it! Thanks For the Support!
This DYI saved me a lot of money. BIG THANKS!!
Glad I could help!
Good morning I'm from Miami dade and was having issues with my washer as u explained In the video. I ordered the parts from your link they came right away. I had my drill and followed your directions. My wife so happy now it really solved the banging problem and being off balance. I just wanna thank you and say I appreciate u and this video. Saved a ton of money doing it myself GOD BLESS... CMV ‼️
You’re welcome thanks for watching my video👍🏻👍🏻💯💯
Thank you so much!! Totally fixed my problem, now I can wash at home again! 😊
What a lifesaver. Video was long, but I think it was necessary to explain all the details to look out for keep it up.
Great video. Thanks for showing about disconnecting and connecting the wires in the back right side.
Dude what a nice and well explained video. Save me a lot a money
Totally fixed my problem, Samsung repair guy said it would cost between $300 and $500 to fix the issue. I ordered the parts off Amazon for $50. I then followed the steps in your video! Thanks my friend
Glad My Video Helped you Repair it Yourself and Save Money, That’s My Goal! Thanks For Watching!
Your instructions were exactly on point and made our DIY repair easier. We have the exact washer with the exact balance issues you described. I bought the rods (under $50) from your link, followed your video step by step and the washer is working as new again! I looked at several other instructional videos for this washer repair, and yours was by far the easiest to follow and understand. Thanks.
Happy to Hear My Video Helped With Your Washer Repair!
Just want to say thank you for this video! I watched this a couple of times and was able to replace the stabilizer rods in 30 minutes. Thank you and happy holidays.
I am Glad to hear My Video Helped, It Means A lot! Thanks for Watching and Happy New Year!
Incredible video! I followed your guidance exactly and used the suggested springs to fix my washer. Samsung wanted $300 just for a diagnostic, which would not have been of much use anyway. I found the video on how to run the auto diagnostic in 30 sec. It's just a series of button presses. No local technician would touch the washer either. I decided to try the suspension replacement and now I have a washer running like new. Way cheaper and far less wasteful than getting a new washer. Thank you so much! ❤
You are Very Welcome! So Happy to Hear My Video Was Helpful to you! Thanks for the Support!!!
Great video; thanks for the help. The project went smoothly.
Thank you! I have the same washer same problem thanks to your video is fixed!!😊😊😊😊😊😊😊
Happy to Help! 👍🏻
Wow great instructional video! Ordering the parts now!
Great video and explanations!! I replaced mine tonight by myself, and it took about 25 minutes total watching your video and doing the work at the same time. Thank you!
Glad it helped! Thanks for Watching!
Thanks! Very complete and knowledgeable. Great Help! Saved BIG MONEY!
Glad My Video Was Able to Help! Thank You Very Much for Your Support, it is very much appreciated!
Yes, after replacing the shock absorbers (armsprings) of a Samsung washing machine, it is necessary to perform calibration. This will help bring the device up to speed with the new components and correctly recognize load balancing.
To perform calibration, follow these steps:
1. Make sure the drum is empty. It is important that there is no laundry in the car.
2. Close the door.
3. Turn off the power.
4. Press and hold the Temp and Delay End button at the same time, return the power without releasing the button.
5. You will see the indicators light up, continue to press the buttons for 3 seconds.
6. The machine will then enter calibration mode. Wait for the process to complete (usually takes about 3 minutes) and the machine will turn off automatically.
After calibration is completed, the device should work normally. If the problem persists, there may be a problem with the balance sensor, motor, or electronic control.
In addition, the Samsung manual indicates that the Ub error may pop up if the drum is not loaded evenly. I advise you to make sure that the client loads laundry into the drum correctly.
Hope this helps!
I did the repair. It was a lot simpler than I expected. I put a load of laundry in and it kept filling like to where it almost overflowed so I emptied it, drained the water and did a calibration but it still is over filling. Any ideas ??
@@garryweber4199 water level sensor
Thank you man. I bought the items you had in the description and installed them the way you showed in the video. Thanks for saving me a ton of money.
No problem 👍 I am Glad My Video Was Helpful to You. Thanks for Watching.
Thanks brother. I used this video and was able to change out the suspension rods no problem!
I didn’t remove the rear metal panel and only unplugged two wires. The wire leading to the digital panel and the one leading to the back of the top plastic panel. A lot easier when you have an extra pair of hands. Just be careful when pulling the top up off the washer, (some connected wires and tubing).
Overall, not too difficult!
Took a chance after watching your video- took a half hour washer works like new thank you
Great job! I am Glad My Video Was Helpful, Thanks for Watching!
Hello. Great instructions.
Now I’ve replaced the rods. And a week later. I’m back to constant off balance. Any ideas
Perfect step by step directions! Thanks!
You're welcome! Glad My Video was Helpful!
I replaced my suspension rods on my Samsung washing machine and 2 weeks later started to be unbalanced again and making loud sounds. Please help!
Thank you so much for this very informative video. This helped me to fix our washing machine - now it’s running great! Very detailed step by step guide.
Glad My Video Was Helpful to you1 Thanks for Watching!
Thank you brother, very concise instructions very helpful. Those spring rods a very gooey and sticky. You were right about them . Merry Christmas.
You’re welcome merry Christmas to you and your loved ones. Thanks for watching my video.👍🏻👍🏻💯💯
Super helpful - able to do perfectly with your help. Many thanks
Great to Hear! Glad My Video Was Able to Help You!
This was exactly the help I needed. Problem solved. Thank you very much for taking the time to make this video.
You’re Welcome! Happy to hear My Video was Helpful. 😁
Awesome video. Great communication. Thank you so much as my wife is super happy now
Glad I could help! Thanks for Watching!
Very good instucyional DIY video! Thank you
Glad you enjoyed it! Thanks for Watching!
Thanks brother!!!
You’re Welcome! Thanks For Watching my Video!
Dude, thanks. Watch video and did this job. Made it easy, and worked great. Thanks
Great to hear! Thanks to Watching!
A lil advice. To balance these washers turn on power, press temp and delay end together for 3 seconds then press start. It will put the washer in balance mode.
Excellent video - im thinking this could be my problem but was frustrated because the washer is not very old. Keep up the good work
I am Glad my Video Helps, Thanks for Watching!
You are a lifesaver, my friend! I was ready to buy a new washer but you showed me how to fix it for $40. Is there any way I can send you a tip as a thank you?
You are Very Welcome, I am Glad to Hear My Video Helped! I have linked ways you can send a tip in the description of the video. Thank You so Much For Watching and For the Support!
Question, the washer model I have is different from what I'm seeing online in parts #'s and in CZcams videos.
I have a
samsung active water jet
WA50t530
Is it that the parts were upgraded??
Any help? Thanks
Thanks!
You’re Welcome! I am glad to hear that My Video Helped you Fix your Samsung Washer. Thanks So Much for the Tip and Support It is Truly Appreciates!
I have the same Samsung washing machine I change those rods out put it back together and it still knocking against the tub, so what else can I look at that it could be the problem? By the way I did put dampening Grease on those components before I install them I seen another videos saying that sticky stuff has to be on there in order for it to stop knocking completely. But it's still knocking can you help me out with that?
These are great instructions and tomorrow I am going to replace the rods on my washer. But I have a question - Where does the spring end of the rod attach to? Is it to the bottom of the drum?
It Would be to the Bottom of the Outer Tub.
I have a Samsung washer that won’t spin, it’s trying to spin but isn’t quite catching the washing basket. Any idea what might cause this or where I should be looking for more information?
Could it be the shocks even though it spins fine when it's empty?
Any other ideas on what it could be?
Mine has no delay button. I replaced rods mo problem but still getting off balance
What can I say that all the other positive comments haven't already said? Thank You!
Thank you too! Happy to Hear My Video Was Helpful!
Tried replacing the rods and calibrated the drum and it still bangs around like crazy 😫
What happens if the rods were changed but the washer still shakes during spin cycle? Could it be something else other than bad installation?
Ok I replaced and it’s the same ..my washer is only almost 2 Yrs old
@@rebeccabazaldua4683there is a recall on these samsung washers some guy just posted the info on that. I'm calling Samsung corporate office about this recall they issued.
I have a lot of Samsung stuff. I like all if it. Appliance guy said stay away from their washing machines.
We did this repair just this morning. Unfortunately, our washer is still getting out of balance. The banging isn't nearly as bad, but we're getting the unbalanced code. Any suggestions?
im having the same issue. Did you find a resolution?
None of the suspension rods looked damaged?
They will never look damage, and in this model is hard to tell when they are bad sometimes when you push the drum and tub down in a bounce more than once that means the shocks are bad, but sometimes in this Samsung’s it doesn’t do it however, I’m going to leave you this link that way you see how it will bounce if they are bad. The only thing is that the link is from a whirlpool but it’s similar issue
czcams.com/video/HvTqvm_WNHQ/video.htmlsi=CvgSUsy4hTvuPPTe
Literally replaced the suspension rods & it was back to the same error the next day.
I changed the shocks 2x . This washer needs to be loaded extremely carefully to have equal weight on all sides. I usually have to wash every load 3x to get it to run without unbalancing . Do not purchase this!
This Samsung washer had a recall for 2021, 2022. I bought mine new in june 2021 and 2 yrs later its doing tge same thing it wont spin tge water out. I just heard about this recall and i am calling the appliance store where i bought my samsung washer and i will be telling them about that recall on these samsung washers and i will ask them why didnt they tell us about these recalls. I will tell them that i am calling samsung about their recall and they better refund me my money or they will give me a new washing machine or i will call my attorney to go after them for fraud.
Curious, what became of your situation? With the recall, any progress?