meskipun hasil bazingnya gagal. tapi ini merupakan video yang success (jadi saya tidak perlu coba hehehe) .... memang agak susah brazing di besi..... tapi saya yakin akan sukses di tembaga dan alumunium
Primero limpia bien la pieza con cepillo de acero o piedra. No apliques fuego a la varilla. Aplica fuego a la pieza, pero más del que estás aplicando. El calor de la pieza es quien funde a la varilla. El fuego directo a la varilla no ayuda sino que daña la varilla. El fuego se aplica a la pieza que quieres soldar
That's not welding rod or even brazing rod, That's solder. I also recommend applying a liquid flux designed for steel if you're gonna solder to it. You'll need to work the heat into the metal, don't directly heat the spot where the solder is going. brush your metal joints with flux, then apply heat just behind that and move the torch around to get both parts heated before filling with solder.
looks like it is not hot enough. Perhaps a larger torch with higher BTU? second maybe needed. You may also consider wire-brushing the metal so it is clean. Lastly check if the bricks you are using are absorbing too much of the applied heat. You may need to move the work area further away from the brick or use some other method of holding the work pieces
Nothing welds to galvanizing? You need to grind of the galv 1st or use oxy and burn it off... If burning it off use a mask as the fumes are toxic. Then try it again heating the mating surface up to temp 1st as others say. Purchased some to try as well ...
Kawat brazing rod... Video ini misleading karena judulnya welding... lebih tepat disebut brazing. Satu level di atas soldering. Perbedaan soldering dan brazing hanya di panas... soldering tidak perlu memanaskan workpiece, brazing perlu memanaskan workpiece tanpa perlu mencapai titik lebur, welding perlu memanaskan workpiece hingga titik lebur.
800 rupees some 10 wires only online and also waist many gas can 300 per bottel so why waist money just buy 5000 welding machine and 20 rupees 4 rods come weld good
The rods may well be garbage but you are supposed to heat the job up not the rod itself, pieces need to be thoroughly clean.
meskipun hasil bazingnya gagal. tapi ini merupakan video yang success (jadi saya tidak perlu coba hehehe) .... memang agak susah brazing di besi..... tapi saya yakin akan sukses di tembaga dan alumunium
Good attempt. Keep it up.
Primero limpia bien la pieza con cepillo de acero o piedra. No apliques fuego a la varilla. Aplica fuego a la pieza, pero más del que estás aplicando. El calor de la pieza es quien funde a la varilla. El fuego directo a la varilla no ayuda sino que daña la varilla. El fuego se aplica a la pieza que quieres soldar
This is helpful, thank you!
the idea is get the metal hot enough that when the rod melts by touching the rod on the metal don't use the flame to melt the rod
I'm glad I bought welder
That's not welding rod or even brazing rod, That's solder.
I also recommend applying a liquid flux designed for steel if you're gonna solder to it.
You'll need to work the heat into the metal, don't directly heat the spot where the solder is going.
brush your metal joints with flux, then apply heat just behind that and move the torch around to get both parts heated before filling with solder.
Aluminium road not suitable iron road steel road and copper.
Only useful same metirial.
And pype heating like red colour comes ofter welding perfect.
looks like it is not hot enough. Perhaps a larger torch with higher BTU? second maybe needed. You may also consider wire-brushing the metal so it is clean. Lastly check if the bricks you are using are absorbing too much of the applied heat. You may need to move the work area further away from the brick or use some other method of holding the work pieces
Thank you, I will try it again and hope the result is better.
boyset na jawa kaw wa kay natabang..!!
Donde puedo conseguir ese material de apoete
Nothing welds to galvanizing? You need to grind of the galv 1st or use oxy and burn it off... If burning it off use a mask as the fumes are toxic. Then try it again heating the mating surface up to temp 1st as others say. Purchased some to try as well ...
you can only weld aluminum with those rods
Good thing these things don't work or I'd be out of a job...
I just came here to seek out advice from all the welding experts in the comment section
Itu pake kawat apa
Kawat brazing rod... Video ini misleading karena judulnya welding... lebih tepat disebut brazing. Satu level di atas soldering. Perbedaan soldering dan brazing hanya di panas... soldering tidak perlu memanaskan workpiece, brazing perlu memanaskan workpiece tanpa perlu mencapai titik lebur, welding perlu memanaskan workpiece hingga titik lebur.
It's just lead free solder.
only aluminum with those rods
This temperature is to low. 🙄
Will heat up more
Where is your FLUX? Not working because you have no flux?
It can be done if you have enough knowledge
Ok, thank for comment.
dapat inalis muna yung galvanize hhhh
pahingi link ng aluminum rod na binili mo sir...order ako shopee
AliExpress brother
Kalo mau nempel harus pake flux
Ilmu sesat kalo kaya gini
Maybe need flux powder
800 rupees some 10 wires only online and also waist many gas can 300 per bottel so why waist money just buy 5000 welding machine and 20 rupees 4 rods come weld good
yes
@@khasi8073 hi
Kahane ho
He is just showing diy hacks not advicing the viewers to try it and earn money on this....
Wow, you have no clue, so many mistakes.
di marunong mag hinang amp
Asi no se suelda 😂