1. Do not provide crank bar 2. The stirrups spacing should be maximum at supports 3. The angle. Of hook not designed for 135degrees 4.there is no designed for development length according to 0.87*fy*dia/4toeb*d 5.the Bending wires not tiet properly..... Thank you sir 😍
Would u mind turn on the CC so that words are on the screen be recorded as still picture and we can capture the main mistakes in this lecture without retyping? Please and TIA.
When you point out these mistakes, do they rectify them, or do they carry on and pour the concrete ? Nice to ‘now video as I’m in the middle of constructing my own house. 👍👍👍
Dear, crank bar is not provided for shear resistance, but it is provided to encounter negative moment at the support or any position it needed. Secondly in SMRF design code recommends the spacing btw stirrup at the support should be less than 4in. And at the last, according to the code i never see 135 bending in stirrup of the beam. Thank you.
yaar waisay samaj zara be nae aaye. aap asan language use kerain instead of technical terms. ta kay aik normal person be samaj jae. or saath main solution be be bataen, assan basha mai.
@@MasterCivilEngineering top bars are mainly there to hold up the stirrups, or for negative moment, or to reduce the neutral axis depth. The bottom bars resist the tensile stresses from bending action
Amazing work
1. Do not provide crank bar
2. The stirrups spacing should be maximum at supports
3. The angle. Of hook not designed for 135degrees
4.there is no designed for development length according to
0.87*fy*dia/4toeb*d
5.the Bending wires not tiet properly..... Thank you sir 😍
stirups minimum space at supports ..l/4 length..centre space more
Great lecturing, thank you.
Great video of the REAL WORLD...thank you!
Alayqumisalam. Watching from Philippines.
Good
Thank you for the information brother.....do more videos bro
its very clear. thanks for the info
Can you show an example of 135 deg stirrup bars as most people are using 90 deg. ?
Waalaikum salam....god !! Salam from indonesia..
Good information bro thq alot 🤜🤛❤
Welcome 🙏
Sir make a video for design of cantilever beam and reinforcement details and SF, BF
Nice 👍👍👍👍👍 information sir
Would u mind turn on the CC so that words are on the screen be recorded as still picture and we can capture the main mistakes in this lecture without retyping? Please and TIA.
When you point out these mistakes, do they rectify them, or do they carry on and pour the concrete ? Nice to ‘now video as I’m in the middle of constructing my own house. 👍👍👍
I would like someone to answer the question
You need hooks spliced to beam steel thus tying in beam to columb.
what is the minimum and maximum space of stirrups? in L/4 and in the middle ?
Good commentary. Ur right.
Dear, crank bar is not provided for shear resistance, but it is provided to encounter negative moment at the support or any position it needed.
Secondly in SMRF design code recommends the spacing btw stirrup at the support should be less than 4in.
And at the last, according to the code i never see 135 bending in stirrup of the beam.
Thank you.
Please make a video on how to check beam shutting line level & plumb bob
Yar hum ny gar Ka tamerr Kia Abi beAm kase deay chath Abi tak nhi banaaya hin
That problem should have been prevented if there was an active site/resident engineer on that construction.
Crank not mostly given instead extra bars are given in L/4 at top reinforcement to counter shear at junctions
Suuuoper Tq u
developing lenth kisay banaty hae?
Sir why we are provided max steel reinforcement bare in bottom of simply supported beam
Greetings Sirji,
Does the undersize steel and all the mistakes get certified by the building inspector before pouring concrete?
Sir Why captions is not available
Thank you Sir 🙏🙏
Good Job
Column striupps is also not there inside the depth of beam junctions...
Hello, I have some cracks that have developed. May I send you a video?
Sir can you please give some idea of 17.5 feet beam
noted ‼️💯
Sir evn they did nt put the crank bar in beam why??
Sir Please .show the drawing of crank bar
Walaikum assalam bhai
The problem there is that the engr who signed the design did not see it but he makes guarantee for the building.
yaar waisay samaj zara be nae aaye. aap asan language use kerain instead of technical terms. ta kay aik normal person be samaj jae. or saath main solution be be bataen, assan basha mai.
top bars transfer load to bottom bars?? that's not how beams work...
Yes dear
@@MasterCivilEngineering top bars are mainly there to hold up the stirrups, or for negative moment, or to reduce the neutral axis depth. The bottom bars resist the tensile stresses from bending action
Stirrups are used for shear while top bars are used for negative moment at supports
This is Ileagal ....
Report this construction
True
Okay
Not ok amigo
This building will collapse
Video solutions of civil engineering questions here
Thank you sir do more vedio
el gancho de los estribos no es correcto
The hook. That’s one of the mistake
Right bro
Okay okay okay okay
You know why it's all mistake? Ba cause some already it budgets is in the pocket of the foreman
All of them are mistakes.....
Beam is full of mistakes bro
Etrierii nu sunt corecti , nu ai etrieri in noduri ,ciocuri la barele de la grinzi