If OV/UV light is continuously on means-undervoltage fault UV/OV light is blinking means-overvoltage fault occured,check your incoming phase to phase voltage(RYB)
@@Ns-16T yeah..but I have other equipments connected for uv/ov , dry run etc... but anyway recently therr was a thunder and the LT box stopped working so I removed it all
If power LED blink means phase reversal problem is occured or some other TX/RX and network light and i1/i2 blink- i1/i2 both blinking -pump on i1 blinking-single phasing network light based network singnal tx/rx blink means communication is turned on
Mpower + is for both 1ph/3ph and mpower pro is for 3ph only -Mpower+ is only for ON/OFF purpose only Mpower pro-all the safety features available single phasing/phase unbalance,overvoltage/undervoltage,dry run,phase reversal......
Bro indhulo aenny sims use chesukoacchu bro
1
Automatic on aytunde
Spr enka manchi video s chesi chueinchandi hemanth
స్టార్ డెల్టా స్టేటర్ కి కనెక్షన్ ఎలా వీడియో పేటండి బ్రో
Buhj
Strbltbakske..khkshv
Same connection for both DOL/STAR DELTA but you can adjust the star delta Timer on the unit
Bro working lo unnadi kani sms ravam ledu
SMS balance vunda and msg vasthanduku oka pampali aa number ki aa codes list Lo SMS enabler ani vuntadi Choodu code
Enni years pani chestundi... Chinese product laga thondaraga padavtunda
18 months warranty bro l&t company di idhi
సంపులో నీలు le నప్పుడు sms kanee vasthada motor ఆగి pothunda
How to convert manuval mode to autoode
Ov/uv red light is on. When calling and press 1 for on. Gives error voltage fault. Please give solution
Wait until light is gone, it is not ur fault, it is power fault from source , it will change later
@@maligireddyhemanthreddy7889 Thanks. I put it in bypass mode and now I can turn on even with voltage fault.
If OV/UV light is continuously on means-undervoltage fault UV/OV light is blinking means-overvoltage fault occured,check your incoming phase to phase voltage(RYB)
@@jeethuutubebye pass mode is only for temporary usage not for long usage,if byepass mode enabled means all the protections are byepassed
@@Ns-16T yeah..but I have other equipments connected for uv/ov , dry run etc... but anyway recently therr was a thunder and the LT box stopped working so I removed it all
Bro two phone numbers ela link up cheyali
Mu 2 contact
Single phase motor set or not set
This model is only suitable for 3phase,another model is MPOWER + suitable for both single phase/three phase
How to connect M power pro for bch start delta starter?
Cost bro
5700
Hi మీ ఫోన్ నెంబర్
Send delta Starter wairing
👍👍
Rilapatokutodi anna
3 lights blink avutunnaie kaani on kaavadam ledhu
If power LED blink means phase reversal problem is occured or some other TX/RX and network light and i1/i2 blink- i1/i2 both blinking -pump on i1 blinking-single phasing network light based network singnal tx/rx blink means communication is turned on
power off ayinapudu , call vastada
Radu power vachhinappudu vasthadi
@@maligireddyhemanthreddy7889 power poyinapudu . call ravataniki e company lo ledha device
Hi
Off avadam ledu bro
Manual ga off chay bro starter left white button tho
Bayya signal raavatam ledhu
Vara SIM try cheii bro
U can try other network like AIRTEL/VODAFONE/BSNL
but JIO 4g is not supported for both MPOWER+/MPOWER PRO unit
User manual pdf send me plz
Which one is better between plus or Pro
Pro
Mpower + is for both 1ph/3ph and mpower pro is for 3ph only -Mpower+ is only for ON/OFF purpose only
Mpower pro-all the safety features available single phasing/phase unbalance,overvoltage/undervoltage,dry run,phase reversal......
Active mode bapas mode
Active manual
Active mode-it contains both AUTO/MANUAL mode
Byepass mode-all the protections are byepassed
Ne number pampu bro …oka connection doubt
Mee phone number
Bro send me your number…connect cheyadam ravatle
బయ్యా ఇది పనిచేస్తాడా నాకు 5 HP motor ఉంది palm oil తోటకి కావాలి
How to convert manuval mode to auto mode