Ford Puma MAJOR RUST REPAIR PT10 Rescued From the Brink Phase 2

[@abcdefgh-le6kl]

My compliments for the work done on the Puma and the detailed video's, a fellow Puma driver from Holland.

[@mec-tec]

Hi ! Thanks so much ! I really appreciate your message and support ! Great to hear from a fellow owner in Holland !! 👍👍👍

[@Kylian_Mbappe_gang]

Great

[@philipbunker146]

No complaints with it from where you started on this project Mike!

[@mec-tec]

Thanks mate ! Yep its looking good from where it started 👍👍👍

[@buchholzpatrice6618]

good job 👍

[@mec-tec]

Thanks so much ! 👍👍👍

[@Robin-q2n]

You deserve it to look that good after all that graft. Seriously good work!

[@mec-tec]

Thanks so much ! Glad you like it ! 👍👍👍

[@mikenewman137]

Great job, looks really good now

[@mec-tec]

Thanks Mate ! Glad you think so 👍

[@g3rcq]

BRILLIANT !!! 💯% D

[@mec-tec]

Thanks so much Wak ! 👍

[@jamesrguk]

I knew you wouldn't be able to resist flatting back that hairline mark 😅

[@mec-tec]

🤣🤣 haha yes i couldnt sleep at night otherwise 🙈🤣🤣👍👍

[@Cavalier_Steve]

Looks absolutely spot on ! Well done mate! Should get a nice clean MOT no problem well done!

[@mec-tec]

Thanks so much mate ! Glad you think so ! Fingers crossed ! 🤞🤞🤞👍👍👍

[@hojo9115]

Cracking job mate, you certainly dont skimp on any of the work youve done. Filler takes quite a while to get right but its worth it. Looks 100% better. Best of luck when you check other side

[@mec-tec]

Thanks so much ! Glad you like it ! Its deffo time consuming but well worth it 👍👍👍

[@WaddedBliss]

The Millie's looking great, Mike. I got my new cat today from Rochester. I'd forgotten how much fun they are to drive. Going to take her for a proper ragging around some bends tomorrow. 😁

[@mec-tec]

Thanks so much ! Great to hear you have a new Cat, hope you have lots of fun with it ! 👍

[@WaddedBliss]

@@mec-tec Got a new tyre and the tracking done on the way home. It was drifting horribly when I changed lanes on the M25. Much better now. I squirted it up from 30 to 60 in a couple of seconds earlier, just for a bit of fun. 😂

[@robpassfield1035]

i think you should have used a guidecoat when flattening with the 1200 grit paper.

[@mec-tec]

Hi, yes I think you could be right there 👍

[@TK42138]

👏👏👏👏

[@mec-tec]

Thanku ! 👍👍👍

[@timh301]

Really nice job with the paint. Did you use 1k or 2k lacquer?

[@mec-tec]

Thanks so much ! I used 2k Lacquer in a can with the ring pull activator on the bottom 👍

[@eleanoronatrike.6151]

Can you use a different tune please s
this music just drones on you need something different.

[@deanmathers4483]

Is there a specific method when tightening the axle brackets to the underbody as there is a little bit of play, I wasn't sure if they are supposed to fully tightened when r cars weight is fully on the wheels/ground?

[@mec-tec]

Hi yes you are correct about the weight being on the axle when you tighten them, when i moved the axle stands under the axle in the video, that put the weight on the suspension, so it would be the same as being on the ground, hope this helps 👍👍

[@jonflounders1541]

Mike your wasted as a cabbie you should be a painter and comedian (wrong hole) stop it😂😂😂

[@mec-tec]

😂😂haha thanks so much mate, I really appreciate the msg and support 👍

[@bobward2101]

I never doubted your ability from the start that is body shop quality M8 !🔝🍌 I’m isolating with Covid as it is spreading like wild wildfire around Brum. Can we have a “Short will it start & drive out for a wash and brush up job Video ?” 🙏🏼👍🏻

[@mec-tec]

Thanks so much Bob, I really appreciate your support ! Sorry to hear your Isolating, wish you a speedy recovery ! I will look into if I can do a short, I've never done one before haha 👍