MN D90 Land Rover Defender with DIY Rover V8 Sound and Lights, WPL 2 Speed Transmission
Vložit
- čas přidán 28. 08. 2024
- In this video: The MN Model D90 Land Rover Defender gets a 3.5l Rover V8 with automatic 3 speed transmission as well as a full set of lights. It also has multiple horn sounds and a 2 speed WPL transmission, used as off road reducer.
Your supplier for the pre assembled Open Source Sound & Light Controller: www.pcbway.com/
Sound Controller:
Virtual 3 speed transmission: • WPL B36 URAL-375D With...
Flysky support: • The Best Engine Sound ...
Revving sound, Kenworth sounds: • ESP32 Arduino RC sound...
SCANIA V8 Open Pipe: • Worlds Most Realistic ...
Light & sound controller features:
- Sampling rate up to 22’050Hz, instead of 16’000
- Multiple sounds can play simultaneously
- real DAC outputs, no R/C filter circuit required
- the variable speed engine sound can play at the same time as an additional sound with fixed speed (a horn or a siren for example)
- A lot of pre configured vehicles are available
- special sounds included like: „Martinshorn“ fire truck horn, US Police siren, Swiss post bus horn, train horn, car horn, MAN TGA truck horn
- Engine sounds for: Land Rover Defender V8, ford Mustang, Chevy Nova, Dodge Challenger, MG B GT V8, LaFerrari, Scania V8, Ural V8, Kenworth, CAT, Detroit Diesel etc.
- Air brake & jake brake sounds
- Output for vibrating motor, which simulates engine vibrations
- Vehicle inertia simulation (if crawler type ESC is connected to pin 33)
- Virtual clutch, making the engine sound much more realistic (if crawler type ESC is connected to pin 33)
- simulated manual 3 speed, automatic & double clutch transmissions
- The TAMIYA 3 speed transmission is synchronised in software and can be shifted while driving
- Many light functions like headlight, tale light, brake light, indicators, blue light, foglight, sidelights, high & low beam
- 6 PWM RC servo signal inputs
- 13 light outputs
- PWM, PPM, IBUS & SBUS communication, makes it compatible with most common remotes
- The pre assembled SMD PCB can easily be ordered according to: github.com/The...
Banggood Weekly Coupon Deals: goo.gl/D8B1Mu
Banggood Weekly Discount Deals: goo.gl/uGS7Lf
Material links:
- PCB including SMD components assembling: www.pcbway.com/
- MN D90 and accessories: www.banggood.c...
- ESP32 board: www.banggood.c...
- PAM8403 amplifier: www.banggood.c...
- Speaker: www.banggood.c...
My DIY Open Source Arduino Stuff:
github.com/The...
github.com/The...
github.com/The...
www.thingivers...
github.com/The...
Check out my other RC videos: • Remote control
My GitHub: github.com/The...
My Thingiverse: www.thingivers...
Follow me on Twitter: / thediyguy999
on Flickr: www.flickr.com...
and on Instagram: / thediyguy999
If you want to support this channel:
/ thediyguy999
paypal.me/thed...
#TheDIYGuy999 #WPL #V8
Nice light and sound upgrades
Thank you
Super!
Thank you
very nice brother
Thank you. V8 and automatic transmission = cool. BTW, it's using my new SBUS micro receiver.
@@TheDIYGuy999
how much it costs for 1 pcs micro SBUS if ordered on PCBWAY?
@@TheDIYGuy999
I mean per 5 pcs
@@AatTsani It was $68 including shipping.
How to buy complete light and sound kit
If you get this model, you need a larger figure than the one DIYGuy999 has used. You need one that is 6 inches in height at least. Unfortunately it is misleading because MN Model designed the seats too small, so smaller 4 or 3.75 inch action figures will fit in the seats. The underscale seats are about the only thing glaringly wrong on these model trucks
I have another issue that the engine sound become louder(idling sound,no acceleration sound)when throttle up/down if i commented out the AUTO_LIGHTS,this happens to my FlySky GT3C & Jumper T16 which is using SBUS receiver.
ficou perfeito!
Thank you
o senhor poderia ajudar tirar umas dúvidas? tem algum contato?
Please ask your questions here: www.rc-modellbau-portal.de/index.php?threads/esp32-arduino-rc-sound-und-licht-controller.7183/
Hi.
Been following this project for some time. Finaly got around to order from pcbway the other day.
Thought I'd do a mock-up while waiting.
I use a frSky rx8r reciever. And I cannot figure out if the sbus is inverted or not. And what I should do if it is, or not :-) can I just flip the variable in the radio setup file and see what works?
Also. This is a 16ch reciever. Can I change the ch mapping to anything amongst those 16? Or am I limited to the first 13 channels?
Just try which mode is correct. I assume true. You can connect a 16CH SBUS signal, the controller will use them according to "adjustmentsRemote.xlsx"
@@TheDIYGuy999 cool.
Thanks👍
Kann man das eigentlich machen dass das Licht beim Starten nicht nur dunkel ist sondern auch nen bischen flackert? Und dass das Licht
(Blinker, Scheinwerfer usw.) langsam von ganz dunkel auf hell geht?
Also nicht einfach nur an sondern wie bei einem echten Auto dass das Licht quasi Energie bekommt und dadurch immer heller wird bis es die maximale Energie erreicht hat. Und umgekehrt für Aus auch? (ich hoffe man versteht was ich meine). Habe absolut keine Ahnung von RC Elektronik oder generell von Elektronik, aber wie ich sehe hast du schon ähnliches eingebaut. Vielleicht einfach so als Anregung.
Noch nicht. Werde es wohl noch programmieren.
@@TheDIYGuy999 Nice. Ein Abo hast du auf jeden Fall. Noch nie so ein nices RC gesehen.
A lot of codes changed to previous.I have an issue that the reverse light up(car & truck) & reverse sound(truck only) "intermittently" when engine idling.Im using PWM radio Flysky GT3C(already calibrated st & thr channels) and only selected the RGT_EX86100 in codes can work with sound and light controller.
Is there anywhere i can adjust in the codes to eliminate the annoying intermittent noise?
Looks like your PWM signals are not stable. You could try to enlarge
const uint16_t pulseNeutral = 30;
@@TheDIYGuy999 i need to set it to 100 and problem solved.
Erster :D
Viel Spass!