Halo LED Projector Headlights Wiring Installation - Spec-D Tuning
Vložit
- čas přidán 25. 08. 2024
- Spec-D Headlights at CARiD.com
www.carid.com/s...
Lean how to install Halo LED Projector Headlights Wiring.
Custom Headlights at CARiD.com
www.carid.com/h...
To any one doing these lights . If you want your halos to light up while driving during the day i suggest you hook them up to the day time driving lights (aka side markers). The instructions in this video say to hook them up to your hi/low beams. But if you do that they will only light up during night time driving. I learned this the hard way and had to do them over again.
Got a questions. I have 2 red wires, 2 white and 2 black. I want to install the way you said. Do I hook you red to the turn signal and the white to the running lights and black to ground? I have a 96 toyota 4runner. I hook up the red to turn signal and it blinks and the emergency lights works for the halos too. I'm not sure where does the white one connect too.
If the parts and wires were properly labeled and described, it would have helped alot! 1 of the existing bulbs actually inserts into a hole on the new unit. The unit we have for a Honda Accord, came with a small attached unidentified part (glued on with sticky tape) that had a wrapped connector that needed to go "somewhere", with a red and black wire. After inserting the bulb harness into the correct hole, I took out the small bulb on the last remaining thing left, and voila, that little connector inserted into where the old bulb came out. This video left ALOT of important steps out which made installation very confusing for the novice. So now the 1st light towards the inside is extremely dim, then the high and low beams work correctly, the spot where we had to insert the old bulb harness is dim as heck because its a regular old bulb, and the halos work great as well as all the side lights. The wiring of the white and black wires was helpful tho, so your video wasn't' a complete waste, lol. Crimp connectors were not included in the kit, only 4 of the other connectors. Instructions in the box were pretty bad too.
Oh man. I was looking at these and was excited...until I saw the wiring. I was hoping you just took out the old and plugged in the new lol.
Lol same. I bought them but didn't wire them properly
Same... sooo glad I watched this video before buying the LED Halo model. All that black tape and splicing the factory harness. I'm surprised duct tape wasn't involved.
I would have used small zip ties. Over a period of time, electrical tape looses up and leaves your wires super sticky.
Once you do it it's super easy. If you add a relay to the halos so that they turn on automatically it's even better.
Same smh now I have to get the kit
After watching different install vids about 10 times,..it finally starts to make sense ,..kind of simple !!!
explain
Bought some headlights for my G35 without knowing I would need to wire in the halos and now I'm scared I'm gonna mess them up. Also was it supposed to come with those loose wires like in the video or not? Bcus I didn't get any
at the very end of your video , you did not connect the factory harness to your headlight assembly ?...is it not needed ?...... does the extra wiring you did eliminate the need to connect it ?
Instructions unclear. Blew my motor
lol wow
@Brian Cavanaugh agreed i got the celica lights and the bright light housing is trash and the lights that come with the lights are also trash
Wish I saw this comment sooner.
Thing is my projectore same brand and make have 3 different sets of wires
did you ever figure out the solution? if so i could really use your advice! i’m having the same issue
Why at the end of the installation the head lights are not on when he clearly turned the headlights on before he tested the lights? Did he not plug the headlights back in?
As for a 2014 Ram 3500, the lights fit perfect, the video was excellent and the lights work fine. Thanks Spec D. Used heat shrink tube for the helo/led wires.
Question, do I reallyy need extra wire? I only have 18 and 14 awg wire. If I use the blue splice connectors, can I simply make a connection from the bare LED wires, to the existing harness wires on my car? Was gonna attempt this today so anyone that responds quickly would be greatly appreciated 🙏🏻
I installed these on my 2007 E90 BMW a few months ago. My halos quit working. Do you have any thoughts as to why this is? I've tried tracing the wiring but don't see any specific wires for the halos only for the LEDs. Thanks for any help.
+CARiD Thank you for the reply. If there was a bad connection would that not prevent either LEDs or parking lights from working? Both of those work fine. If I determine that the HALOs need replacing can I replace with CCFL and if so how much trouble and what is the cost? Thanks again.
I connected some halo on my car did all the wiring they all work turn on BUT they are not bright enough. When i got them i check if they work, they did and shine really bright. But when i connected all 3 together they dimmed. What can i do? Btw i connected direct to the oem wire harness. So the halos turn on with the regular projectors.
Just bought a set of these and they are so confusing, I don't understand where the third set of B&W wires from the side of the lights connect too. The "instructions" you sent with the lights don't show how to wire anything and honestly this video is very limited on the actual wiring (doesn't make any sense) considering it also don't show the third set of B&W wires.
I'm trying to install these on a 2006 Dodge Magnum and it's just not working.
I could not get my “brights” to work, but I was able to get all the lights to come on. What is needed to be done to incorporate the brights?
That green wire is the high beams, you'll have to wire up the high beam motor in your projector housing, but also run it to the bulb. This is also a very ghetto way of wiring anything, you should remove the old connector and use water proof connectors and heat shrinks so you don't start a fire.
I received my dual halo LED projectors and installed them today as per this video, my halo rings only light with my headlights not with my running lights. I see in one of your responses that you state they must me connected to running light power. That would have been extremely helpful for the person in this video to state that. Also, my Low beams go out when I go click on my High beams, is that the proper function of these lights? I have already emailed customer support and have not received a response.
I have a black with red wire. How does that work ?
Is there a reason you used tape instead of shrink tubing or a brush on?
Oooo my some people drive ya crazy the way they show you something. Slow down so the people can see what your doing. If you do it THE MR. Rodgers way you will get alot of thumbs !
seeing that the majority of people understood this by the rating and like to dislike ratio, not many people had issues with the speed.
Wow I loved the video brother keep uploading more videos greetings I love it 👍👍👍👍👍
so I have to go through all this wiring for my halo headlights to work?
@@carid 100 bucks in labor
By the looks of it, the headlights are not just plug and play... you need to wire them into the harness to make them work?? I’m fine with wiring the led strip but what about the low and high beams? Are those plug and play or is different wiring needed?
I have three sets of wires ones got a white and black and a black the other two have a set of white and black what do I do ?
Did you connect the wires to the high beam or low beam?
Yes i used a waterproof quick connector. But it did not work. Should i used a quick connector thats not water proof?
I'm confuse there two extra wires an much longer its black white wat do I do with those 2extra wires
I ordered some for a 08 silverado, can I hook up the halos and leds other than the headlights? Where they come on with the parklights
Can you not just tap the halos into your low beam wire so they come one when your headlights are on, and then tap the LEDs into any ACC wire that only comes on when the engine is on to use as DRL and this way they would also stay on when your headlights are on?
I can't see how you are putting the wires inside the connectors. When you put the wires in are they still visible or do they go inside the little cone within the connectors
So i have a 3 set of wires. 3 white and 3 black. Hooked all up. But all my lights come on. I cant make just the halos come on. Why?
i guess im the only one who notices that they used a song from one of the Naruto movie soundtracks? 😂
Just watched this but first thing I said !!
What gauge wire would you use for the extra wires that he quick connected to the headlight socket
16
Hi I just got these Spec-D Halo headlights for my 2003 Ford Focus. I understand what to do, the only problem is is that in this video there is only one pair, or at least he only shows one pair, of black and white wires that go into the male crimp connectors where I have two pairs or four wires of each color. Do I put them all into one crimp connector? Please help. Thanks!
Caleb Osland Thanks for asking this question. I needed to know this for my '04 Focus.
Are these lights bright ?
I would like to know if it is possible to change these bulbs that some blue bulbs?
Y’all need a updated video or send your Mechanics over here
08 dodge ram, do i plug the connector to something? Or just let it hang? Is the splice just for halos?
I just ordered spec/d halo led projectors for my 2004 passat. It came in the mail today and they only have with the 4 blue quick connectors, not any of the extra wires and male connectors, what should i do/where can i buy this stuff?
Does the kit come with the tools to convert the Wires and connect them??? Do I need to buy those blue things and extra wire? I bought the headlight kit what else do I need????
I ordered Spec-D headlights for a 2008 Tundra. The new headlights come with H1 bulbs but my truck has H11 stock bulbs. If I order HID bulbs for the new housing, would I need H1 or H11 HID bulbs?
Mine have 3 white wires do I put all 3 into the male crimp connector?
I know this is an old video but anyone tell me which one is high beam is it the projector side or regular bulb side
I wanted to asked you does the halo supposed to turned on when you have the nite lights or the running day light?
Shouldn't the LED wires be connected to Key on power and not the headlight power? This means the driving lights will only come on with the headlights turned on?
Quick question i got the projector headlight but where did you connect the wires in the low beam or the drl thats usually in th bottom with the small bulb accord 98
I have a 05 4runner with these lights I modified them to fit HID light bulbs, now I have a 07 Yaris and I want to install LED light bulbs, is it possible to install them in these lights? Or they can just be use with common halogen light bulbs?
Have the same set up but my bulbs went out, i replaced now only my high beams work and not my lows, what can it be??? i checked all my fuses there all good
What gauge of the wire of both the headlights and the vehicle?
my halo led lights have the 2 black and 2 white but it also has 2 more wires a black and white where do those connect?
Oscar Enriquez hello did u ever have to change your bubs I’m having a problem now trying to do it
Everytime this question is asked, it's left with no response. I'm still reading the comments to see if was answered.
1 of my four halos isn't working on my 04 Jeep Grand Cherokee Laredo, how do I troubleshoot the problem? What could the issue be?
Everything works but my Halos I've even tried all the other wires in different combos still nothing. Maybe I just got faulty halos idk. Thank You for the walk through
Make sure your model doesn't require a CFFM Inverter. You can also wire these to your fog lights or your daytime running lights
I have a white wire with black strip where does that go? I have three pairs instead of the two on the video
Do you need to do this if buying spyder plug and play headlights???
do the quick connectors come with the set? if not what gauge quick connectors do I need?
Dude, this was THE biggest NIGHTMARE for me! As others have stated, no crimps included, (WHY NOT!!!!!), and the video only show TWO sets of black and white wires when my harness has THREE sets! Also, the wires you attach with the crimp, I , being a complete novice in this field, can’t for the life of me figure out how to locate the hot...
Oh, and you need to have EXTRA wire laying around too... I mean wtf??!
Now after spending an entire Saturday, I’m now up early on Sunday trying to figure out how to put Humpty Dumpty back together again....
Extremely disappointed!,,
Neverrrrr again!
I have the same problem right now and there’s no videos out there to help me , do you have any suggestions ?
I know it’s been 3 years since you commented but it would still help
This is why you read all of the ad before buying something. It clearly states that Professional installation is highly recommended. And if you don't have some spare wire laying around and a few crimp connectors or at least a wire nut and black tape, then you don't have any business hooking this stuff up yourself. You'll end up frying the BCM or ECM if you are that dumb. I think even my Grandma has spare wire and crimp connectors. I mean come on. Where do you live, New York City? Ha ha ha haaa.This next generation are such Nancy boys. Instead of getting on here and bitching like a little girl, take your purse and go down to the auto parts store and buy some supplies. Be a man, not a sissy. Hit it with your purse strap, maybe it will connect itself.
@@hugobalderas9478 having the same issue. Have you had any luck?
I bought these lights for my 2006 dodge magnum and it came with 6 extra wires. 3 black , 3 white , the instructions are useless and so is this video because this only shows 4 extra wires, unlike the 6 mine came with. am I supposed to connect all the black wires together and do the same to the white wires. Then am I supposed to tap them into the low or high beam or both ????? Really need help
I don't really see which wires go to which other than the general idea of color matching. Mine doesn't have the same color as the Halo projector headlight that I bought.
Can you provide the names or Amazon links of the crimp connector parts? Thanks!
Can the headlight bulbs be changed out?
Are the crimp connectors a must? Can I use something else?
What are those blue things that tapped the wires together called?
when i received my lights, the driver side halo did not work. spec d sent me a replacement halo light, but i don't know how to install the replacement halos. any advice??
My harness has pink orange and blue and they all get power. How do I know witch one?
I bought the spyder projection light how do I turn them all blue I own a Ford f150. do I have to buy a conversion kit if so which one
I dont understand whats going on here
I got a set and the left halo just wont freaking work. I soldered them toghether so nothing is loose and did it thrice times. The halo just wont work/.already threw out my old ones too.
Got these for a 2002 Dodge Ram 1500 and I got the passenger side to work but having trouble with drivers side. And the turn signal bulb does not fit in the slot where it’s pose to go. Frustrated 😩
ihave a 90 silverado ihave the halo and hid kit but ihave two wires wich idk what there for one is green and the other brown ..?
Is there a video on aiming these headlights?
I plug my lights in and nothing happens even tho my old headlights work
What's a general price people charge for installation? One person gave me a price of $200.
Hi there I just want to know how to adjust the lights please can you tell me
You need to find the wire that is hot with the headlights turned off NOT on to wire the running lights. Otherwise the running lights would only be on when you turn on the headlights.
DId u figure it iut
does this need to be done for my 2001 dodge ram sports model?
i just bought some of these for my 2007 civic, so you have to connect these to parking lights like the blinker? not the high or low beam, because i tried and it doesnt work.
How about wireing it correctly. That’s a horrible job
I Just got halo led projector headlights and mine does not have all these wires.. all it has is 2 red wires that's split and covered by a black cover.. Can you please help me.. how to install them??????!!!!!
I got mine. And I’m no novice I follow directions pretty well. Here’s my problem. I got the 99-04 mustang halo/led and I got 3 sets of wires not 2 and the halos, once hooked up don’t work at all. Everything else works but that one set of wires I think are for parking lights too. Just you don’t give a very good video for us on this. Make another video.
Currently have the same problem... where the hell do the other 2 wires go??
what size do the quick connecters need to be?
I've heard moisture is a common problem. Just received my pair today and silicon sealed them where the outer covering meets the casing as instructed by your manual. any other suggested locations?
+CARiD thank you for your reply! Have since installed them and is currently raining where I'm at and have not had any issues. Happy with the purchase!
Do you need hid bulbs ?
Can you give instruction on how to align them for the road?
My lights dont have the white and black pair of wires they only have one black wire and one red wirr
Can anyone tell me if this lights can be aimed or not
Do they make halo Led projectors for Lincoln LS 06'?
Just to clear things up, you wire the halo lights into the running lights correct not the headlights?
hi, when i installed my LED/Halo headlights for my 2004 celica i tied my white and black wires together from the headlight to the 12volt power source on the parking lights. low beam headlights work, high beam headlights work, blinker works, and halo lights work, but the LED lights don't work. why is this?
#CARiD i want to know the problem with one of my headlights the diamonds on top doesn't work anymore i have no idea why they just dead for a reason
What is the green wire for
What about those blue and red wires?
What kinda bull is this? You spend 160ish or more dollars and then you have to wire them in yourselves?
So I hooked the wrong wires up for the running lights and now the running lights are not coming on. The headlights still work but, I also lost my headlight left on chime if I get out of my truck. Has anyone had this problem?
Just curious as to where I can find this music
You can make it yourself just look up Logic Pro X tutorial
So you dont use the wiring "harness" at all?
i have a 325i 2006 bmw. i was wondering if i connect the halos to my parking lights will my parking lights have to be on in order to see my halos? and i have connected the lights and when i turn on my parking lights the leds come on as well as when i just regularly turn on my headlights
Where did you get the connectors
i
have a 2003 Grand Am 3.4L v6 problem with my headlights i have HID lights with Can-Bus Ballasts the problem that i am having is the when the lights are shinning on the wall or ground it is impossible to adjust cause my head lights has a center piece that is kinda open in the center and i have noticed on the standard halogen bulb has a painted end on the bulb when they work fine but not bright enough so i decided to go with the HID and then noticed that the end of the bulb has no paint on the tip or chrome so my problem is how do i fix this the lights are shinning everywhere but cannot adjust and has big shadows on the ground and on the wall my reflector center piece has no chrome tip is there away that i can make a reflector to make the lights shine better look up the headlights and you can see what i mean about the open center reflector.
i
had led headlights but on of the ballasts gave out and were to costly to buy another set so i then decided to buy the hid kit and oh my the problems with these trying to line up is that am wondering if i should re buy the led lights all over again they were better and clearer than these hid lights that's for sure and i had no problems in lining them up cause the end had a black metal cap on the housing of the the lights and no shadows,
What gage is the wire
I gave a 2000 clk and the halos have 2 pairs red and white wires and one and one pair of red and black wires how would I go through the wiring process?
I have 6 in total, 3 red, 2 white, and one black.
What's the green wire for? Turn signal bulbs perhaps?
Thank you. It would be convenient to just add a headlight harness adaptor that makes it possible to Connect both factory headlamp and additional LED's to the main harness. In my case I have to splice in to the turnsignal wire also and I'm concearned that this would cause problems if the quickconnector loosens or gets damaged in any way. Is there to Your knowledge any other solution where one could avoid cutting into the harness itself? Kind regards from Norway!
Where can I find those connectors and what's called?
Do you plug the connector on the black and red togerher let me know??
@@carid what wires are the parking lights
What about for a jeep wj?