Not being able to use diferent AT wheels is a bummer to me. Just me. Thanks for showing the noise it makes on slow free roll, no other pointed this out, Kudos Bro!
You can get high end pure teflon grease from keyboard sites thats plastic safe and lasts forever but very pricey. Smear a bit of it on the teeth and a lot of that noise/friction should disappear. Would also extend the life of the system. If you are cheap try silicone grease. I would for sure be lubing any gear drive.
Bravo, thanks for the awesome review video about Omni Gear Drive. In regards to the noise you mentioned at 6:10, there might be the large gear gap. If there is a chance, we recommend you can adjust them and see if the situation still there. Keep up the great work.
@@WAVMOB Hey bro, it can be mounted on boards equipped with 6x series motor/hole position. We also notice that the Endurance comes with the same structure, no problem with that.
Tynee Explorer on gear drive is amazing for $1300-$1400 all in cost. Great for off roading and not having to worry about anything getting stuck in the belts or tearing it.
Thanks for vid. Im seriously considering these for my Hadean-B For reliability, simplicity, reliability and most importantly for me, zero belt slippage under heavy braking . That does my OCD in hard! I tighten the belts until there's no slip but then its WAY too tight (poor battery range and motor heat) and too loose is too loose=SLIP. Gear drive would hopefully do away with all that . PS: dad bod 105mm. is there little review in the works? They'll be my next wheel if so.
Looks like this is mostly for production boards, since it's only compatible with D-shaped motor shafts.. Except for flipsky, Diy motors usually use a round shaft only.
If you haven't broken a belt with that many miles than you must not be riding very hard. I was breaking a belt every 1-200 miles but that was likely do to near constant hard accelerations and braking.
Honestly im suprised the belt drive pulled on the omni setup up that hill..maybe the carbon hadean is faster than the bamboo???? Lol jkjk omni is killin it right now with this gear drive setup
What drive gear settling, on the Evolve remote config, are You using for the AT tyres? 66T? And for street wheels can You use both 40T and 38T? Or are those settings just for mileage readings....? 🤔
Yikes, those wheels on the gear drive are mounted backwards! Would love to try that gear drive. I'm glad more and more companies are making them. This will drive price down and make them more affordable!
No but there are better much more suited gear drive systems like newbee esk8 for mountainboard setups. This one lacks torque for off road as it’s geared for street wheels also so it’s size limitations mean AT setups miss out on in some cases crucial torque for off road riding.
@@ajplant96 you are right. I think it's better for street wheels. As I hear another youtuber said they would bring more gear drive kits. For bigger wheels I guess.
I think the sound is because you dont adjust the gears right. I've got a kit just do some adjustments then sound good. and I dont think it should be compared with different ratio rate between belt and gear drive as well the top speed. emmm...
the clunking sound? or the sound when u throttle? If its the clunking sound u are talking about, u are right. and mine was way worse until i reached out to the company and 2 diy guys and re adjusted the gears. it made it better for sure. but even after i got it perfect, still maybe clunky noises that u can feel. Same with the new acedeck
I couldn't live with the sound of drive gears. Belts for life!
Not being able to use diferent AT wheels is a bummer to me. Just me. Thanks for showing the noise it makes on slow free roll, no other pointed this out, Kudos Bro!
You can get high end pure teflon grease from keyboard sites thats plastic safe and lasts forever but very pricey. Smear a bit of it on the teeth and a lot of that noise/friction should disappear. Would also extend the life of the system. If you are cheap try silicone grease.
I would for sure be lubing any gear drive.
Bravo, thanks for the awesome review video about Omni Gear Drive. In regards to the noise you mentioned at 6:10, there might be the large gear gap. If there is a chance, we recommend you can adjust them and see if the situation still there.
Keep up the great work.
Will you guys create a kit for the MBoards endurance????
@@WAVMOB Hey bro, it can be mounted on boards equipped with 6x series motor/hole position. We also notice that the Endurance comes with the same structure, no problem with that.
I love the snow sequence looked cool as hell can’t wait to try this set up
Tynee Explorer on gear drive is amazing for $1300-$1400 all in cost. Great for off roading and not having to worry about anything getting stuck in the belts or tearing it.
Need street wheel review now
Very impressive performance through the snow and leaves
Awesome review! Like the concept of putting it together then forget about the maintenance
Def on my list for 2023 riding season!
Game changer for sure
Thanks for vid. Im seriously considering these for my Hadean-B
For reliability, simplicity, reliability and most importantly for me, zero belt slippage under heavy braking . That does my OCD in hard! I tighten the belts until there's no slip but then its WAY too tight (poor battery range and motor heat) and too loose is too loose=SLIP. Gear drive would hopefully do away with all that .
PS: dad bod 105mm. is there little review in the works? They'll be my next wheel if so.
Looks like this is mostly for production boards, since it's only compatible with D-shaped motor shafts.. Except for flipsky, Diy motors usually use a round shaft only.
This set up is like a tank rides through everything
Idk some to think about it! Great video Fred 👍
Cool set up. I have thousands of miles on my GTR and I have never broken a belt. I do ride off-road too. I guess I been lucky
If you haven't broken a belt with that many miles than you must not be riding very hard. I was breaking a belt every 1-200 miles but that was likely do to near constant hard accelerations and braking.
Another GREAT vid! really informative
Just need better battery technology now. :)
Honestly im suprised the belt drive pulled on the omni setup up that hill..maybe the carbon hadean is faster than the bamboo???? Lol jkjk omni is killin it right now with this gear drive setup
gear ratio is reduced so less torque
What drive gear settling, on the Evolve remote config, are You using for the AT tyres? 66T?
And for street wheels can You use both 40T and 38T?
Or are those settings just for mileage readings....? 🤔
One other thing how much does or will it cost?
Gear drive goes for $299. The AT hubs are another $299.
7:21
contratulations great video have you tested with 105mm wheels on a vidoe or something similar? thanks
i did test em with 105 dad bods! very cool! i think its on my instagram somewhere
Matt from YOC Grip was friendly and the website is user friendly
Have you felt a board that feels comfortable over uneven sidewalk cracks?
Yikes, those wheels on the gear drive are mounted backwards! Would love to try that gear drive. I'm glad more and more companies are making them. This will drive price down and make them more affordable!
according to stock photos, its not… but the tire tred direction doesnt matter much when the tire is this small. dont let it bother u
Paul here will that work for a mbs mountain board?
No but there are better much more suited gear drive systems like newbee esk8 for mountainboard setups. This one lacks torque for off road as it’s geared for street wheels also so it’s size limitations mean AT setups miss out on in some cases crucial torque for off road riding.
@@ajplant96 you are right. I think it's better for street wheels. As I hear another youtuber said they would bring more gear drive kits. For bigger wheels I guess.
Wow the belt drive pulled the gear but not in top speed
I think the sound is because you dont adjust the gears right. I've got a kit just do some adjustments then sound good. and I dont think it should be compared with different ratio rate between belt and gear drive as well the top speed. emmm...
the clunking sound? or the sound when u throttle? If its the clunking sound u are talking about, u are right. and mine was way worse until i reached out to the company and 2 diy guys and re adjusted the gears. it made it better for sure. but even after i got it perfect, still maybe clunky noises that u can feel. Same with the new acedeck
@@esk8unity if those gears were plastic then totally quiet. but not safe. no perfect solution now I guess.
@@esk8unity how did you adjusted? I’m thinking about getting the same setup
whats your personal speed record on a board?
speed isnt really our thing. its more about the skating shredding experience. but here check this out:
czcams.com/video/d3G87_cjtxo/video.html
Yeah man I don't dig the clicky sounds at low speed either.
❤❤❤
nice ! does it comes in black?
is range increased, deceased, or roughly the same with this gear drive?
i think about the same.
wow nice