2009 hyundai santa fe stuck in park drive neutral fixed shifter wont come out of gear shift lock
Vložit
- čas přidán 6. 09. 2024
- 2009 hyundai santa fe stuck in park drive neutral fixed shifter wont come out of gear not the stop light switch not the transmission cable but some thing else.
Your video just save my butt. I was three hours away from homebase, limited tools, and told by locals it would be 5 days before they could look at my car. Found your vid. I figured, I got time and tools and dug in. The two most important take aways were,
1. after manually moving the linkage under the battery tray to park, you have to open the console and get the cable off the shifter, only then can you F' with and move the shifter back. The console has to be pulled out. You showed it, and that was a life saver.
2. At the linkage under the battery tray, you have to play with the adjustment. Testing to see if it goes through all the PRND. It may do park, reverse, neutral, but not drive, hence adjust that an 1/8 at a time until it works all the way through.
Anyway, thank brother saved me time and cash. Made it home.
im glad you were able to make home i cant imagen getting stuck far away, but great job, im glad.
Thank-You for the video!!! My 2010 Santa Fe just jammed in drive. Nursed it home, found your video, followed it step by step and it is working great. Feels like I won the lottery.
I'm glad you did a great job, and thanks for coming to my channel.
Brother, I am not the sharpest knife in the block but you using your camera as a second set of eyes is genius. I never thought of that. Outstanding video. Thanks for taking the time to make it. God bless you sir.
thank you so much for your comment, that helps me a lot, also God bless you and your family.
Girlfriends Santa Fe crapped out after not driving it for two days during a rainy weekend. Shifter was super stuck, managed to get to drive but shifter got stuck in the manual mode. Tried shift release, nothing. Found your video, started disassembly. As another guy mentioned, once i got the battery tray out the inhibitor switch was super rusted. Hit it with some pb blaster and let sit. Shifter seems to be off by a little, when going back to park itll get stuck on reverse unless you force it very quickly. Before i fully take off the inhibitor switch to clean the rust, im hoping the lubricant may do the trick and free it enough. Glad i had this video as a guide, it was a life saver.
great job, and thanks for the time on this channel, hope you can fix the issue on the santa fe.
This was a very good video. I especially appreciate your showing how to remove the shifter and console. Tabs and screws can be hard to locate.
also thank you for your time on the channel that is also very appreciated.
Thx for the vid. This is exactly what's happening with my 08. Stay blessed
Thanks for your comment and God bless you and family
Got it started on neutral but wont shift... any suggestions. Thx
It's the cable. Gonna find a video on that one
@@TGL77 im glad you found the problem in my case it was not the cable but it seemed like it was it took me about 25 minutes to make it work because the only way that the cable is the problem is when it is broken or it is rusty at certain point
I think its whats happening to all the 2008s at 14 yrs of life! I have been endlessly putting money into this vehicle recently :(
Where did you lube it up? Mine is doing the exact same thing. Your video was great!
thanks for commenting on my channel, I lubricated inside of the entire box assembly and the shift lock solenoid, if it does not move at all then do it manually first may be that hepls then try moving the shifter to any gear and at the same time move the lock the prevents the shifter from moving to any gear with your fingers so you can put it in any gear. but also check if the shift lock solenoid is moving if it is bad you have to replace it. stay bless and your family as well.
Very helpful Thank You
thank you.
Hi brother. Thank you for sharing this video. I think my shiter assembly is bad and need to replace. I am still not able to figure out how to detach the grey connector from the main harness, on the passenger side of the assembly. Can you help thanks
hey Brother thanks for coming to my channel, the grey connector on the right side only has a tab that you only have to press it and pull it out at the same time unless it has kind of melt inside and that is why is hard to pull it out but other than that it is only a tab. hope this help
I have 2009 sante fe.wont start in park.i have to put in neutral by putting screw driver in slot.but starts in neutral.
common problem on these vehicles the shifter cable looses the adjustment, but if it starts in nuetral then also check tramsmission range switch to see if it is deffective or rusty, in my case was the inter lock shift solenoid but I fixed just by lubricating it, so check those things. thanks for watching.
Thanks for such a great and detailed video, l removed everything as you did, what l noticed is that when l pressed the break, the solenoid move only sometimes. Does this mean that the problem is there? Thanks I’m advance.
It has to atuate every time lubricate it and keep moving the shifter, normally at the end in most of the cases it works but. It cat take u apto 25 minutes to make lt work also lubricate the whole assembly good luck n stay bless also check brake switch
@@JM-AUTO what kind of lubricant should l use? WD-40?
@@fernandos.7467 silicon spray or some grease in my case i used silicon spray dont use wd-40 because once it dries it makes it bad wd-40 is great but for a very short period of time
@@JM-AUTO
N
I’m having an issue where the shifter doesn’t go all the way into drive or all the way into park. I can push the cable in and out to get it into those positions, but the shifter will get stuck in neutral, skip drive and just hang around in the manual area.
did you open the console box? normally that is where the problem is in most of the cases, and after you open it you have to play with the entire box and lubricate it and make sure the shift solenoid moves freely and not partially if not try to move it manually and lubricate it at the same time
You may have rust bonding the linkage just under the neutral selector. I would lubricate it up with some tranny oil and heat with a torch if you can but be careful.That link goes inside the tranny and dont use penetrant.
Thank you!!!
thank you for your comment
how much does it cost to do this kinda job
Great Vid!... what kind of lube?
spray silicon, and grease, I coudnt record that because my camera ran out of power
My Santa Fe 2008 dont show lights on the PRND when the main lights are ON.
Please, can you tell me how to fix that?
ola Victor thanks for commenting on my channel, now if you watch this video then you can change the shifter selector bulb because the bulb is right under the gear selector cover and you can see the cable of the bulb when I lift it up even if this video was for another purpose but is the same to replace the shifter selector bulb with the difference that you dont have to do every thing I did cause I was fixing the stuck in D, God bless you and your family.
just remove the nob and pry the gear selector cover with a flat head screw driver and there you have the bulb under it, 99% of the time it is the bulb other wise might be wires but first chec the bulb.
@@JM-AUTO Gracias amigo. Eso quería saber, si esos cables que se ven son los de el foquito que ilumina las letras.
2014 hondai elantra gas kilometers padal not axelerat
Amigo, what is the fuse called and where is it located
ola Amigo are you talking about the fuse for the brake lamp switch? which is the same that locks the shifter if the fuse is blown, that is 15amp in the instrument pannel driver side.
@@JM-AUTO I guess thats the fuse you mentioned in the video amigo….I will check all the fuses related to the shifter and trans
@@golfcon yes that is that one that locks the shifter when it blows
@@JM-AUTO Ok , I broke the plastic tubing in half on the shifter cable when pulling it manually to drive or reverse… hopefully I can fix it with some super glue and bondo
Failed to mention engine size. Thumbs down