Thank you very much for this video! I added a Ford accessories remote start/VSS/Hood Latch to a 2017 Ford Focus SE and needed to activate in the BCM and IPC. Couldn't for the life of me figure it out until I watched your video. Thanks again.
You legend!!! I was trying ages to get the correct blocks to load and boom, managed to get my DRL's (after market headlights with DRL) on all the time and super bright! THANKS!!!!!!
Thanks for saving time and money! I need one that I can code the api just to modify an s13 240 bcm lmao we are installing a new harness for it for performance of course. Yell know how expensive it is 😅
Hello there, My car 2017 ford focus odak Can you help me activate these features with the forscan program? Warning when I exceed 120 kilometers Automatic door locking at a speed of 10 km notification when I lock the door alarm with horn shortening the opening and closing times of the windows
good evening. I used forscan on my 2017 focus and now I don't know how to get hood open error. Do you know what changes were made? my hood is manual. and do not mess with codes. but I didn't photograph the changes. thanks
Can I use this software and my laptop to turn off my automatic daytime running lights on my 2012 Ford Focus SEL? I want to sit in a parking lot (parked) to run the radio, heat, or air conditioning with my headlights completely off.
Wow your OBDII adapter works the first time! What model is it? I have to sit there for 30-60 mins trying to get mine to even connect to the Central Config, let alone write to it after.
Hey thanks for the video, I just have an issue, the BCM is not listed, I have the latest version of ForScan with active licence is not even BdyCM or BCMii do you know what can be the problem? is a Ford Escape 2013 2.5l 4x2.
Hey buddy I have a question. I have a 2013 ford focus se hatchback, last owner puts LEDs to low beams with out ballast, some times says low beams fail. After that only one works. But now both not working. I already check fuses and relay. You think the bcm burns out? Thanks in advance
Hey Jared, I have the same problem with my 2017 ST, but when enter BdyCM Central configuration Main I cant load the first block (Loading block 1/6) and reattempts several times until stops. Can you help me out?
I know this is a 3-year-old video, however, I just got a 2019 Ford escape and I was looking at how to disable the auto start/stop. One way I found was through the BdyCM like shown in the video however FORScan prompted that I had to download the SBL file, which I did. Then when I tried loading it, about 70% of it, then it stopped and said it the action was not completed. This then caused a check engine light and an error saying "engine fault service now." Everything seems to run and work just fine besides the error as well as now the vehicle will not remote start via the key fob or the app. If anyone else has experienced this or knows a way to fix this issue, that would be much appreciated.
@@pedromonteiro2644 i just said that comparing to forscan and this bcm access on mk3 focus it is much easier to do all this things on mk2.5 focus with SW called ELM config. Focccus is for mk3 which I don't own so i couldn't try it. I have USB type obd scanner and I recommend it over BT bcs connections is much more stable. You don't want anything to interrupt communication while writing to BCM bcs you could brick the module. I hope that this is the answer you are fine with.
Thank you very much for this video! I added a Ford accessories remote start/VSS/Hood Latch to a 2017 Ford Focus SE and needed to activate in the BCM and IPC. Couldn't for the life of me figure it out until I watched your video. Thanks again.
You legend!!! I was trying ages to get the correct blocks to load and boom, managed to get my DRL's (after market headlights with DRL) on all the time and super bright! THANKS!!!!!!
What setting did you change? Also have aftermarket headlights with Led DRLs
Nice. I see wow on your PC too lol
Thanks for saving time and money! I need one that I can code the api just to modify an s13 240 bcm lmao we are installing a new harness for it for performance of course. Yell know how expensive it is 😅
Hello there,
My car 2017 ford focus odak
Can you help me activate these features with the forscan program?
Warning when I exceed 120 kilometers
Automatic door locking at a speed of 10 km
notification when I lock the door
alarm with horn
shortening the opening and closing times of the windows
Would you know if you can activate the ambient light and the corner lights in the focus? Thank you.
good evening. I used forscan on my 2017 focus and now I don't know how to get hood open error. Do you know what changes were made? my hood is manual. and do not mess with codes. but I didn't photograph the changes. thanks
Can I use this software and my laptop to turn off my automatic daytime running lights on my 2012 Ford Focus SEL? I want to sit in a parking lot (parked) to run the radio, heat, or air conditioning with my headlights completely off.
Try turning your light switch one notch to the left on a focus 2017. On your car I’m not so sure
Wow your OBDII adapter works the first time! What model is it? I have to sit there for 30-60 mins trying to get mine to even connect to the Central Config, let alone write to it after.
When i click on bcm(main), i get an error saying 'service procedure has been interrupted'. Any idea why this is happening?
Very good! What file are you using at 7:49? where down?
Hey thanks for the video, I just have an issue, the BCM is not listed, I have the latest version of ForScan with active licence is not even BdyCM or BCMii do you know what can be the problem? is a Ford Escape 2013 2.5l 4x2.
Hey buddy I have a question. I have a 2013 ford focus se hatchback, last owner puts LEDs to low beams with out ballast, some times says low beams fail. After that only one works. But now both not working. I already check fuses and relay. You think the bcm burns out? Thanks in advance
So you can use HID headlamps now when you program it on BCM?
Can i add the speed indication on my focus mk3 ? Thank you
Hey Jared, I have the same problem with my 2017 ST, but when enter BdyCM Central configuration Main I cant load the first block (Loading block 1/6) and reattempts several times until stops. Can you help me out?
I have a 2014 Ford Focus se but it keeps saying 1999 2002 Ford Focus 1.8 l zetec
will that program a BCM to allow for Intelligent Access?
I know this is a 3-year-old video, however, I just got a 2019 Ford escape and I was looking at how to disable the auto start/stop. One way I found was through the BdyCM like shown in the video however FORScan prompted that I had to download the SBL file, which I did. Then when I tried loading it, about 70% of it, then it stopped and said it the action was not completed. This then caused a check engine light and an error saying "engine fault service now." Everything seems to run and work just fine besides the error as well as now the vehicle will not remote start via the key fob or the app. If anyone else has experienced this or knows a way to fix this issue, that would be much appreciated.
i keep getting the same error except it loads 0% then my lights flicker. did you find a solution?
it says needs to download secondary boot loader, refuses too, then sends me back to square one
Did I miss something still can't Access bdyCM Module configurations.... it's gonna be super nice to have all this option.
I have the same problem bdycm is not listed when forscan start reading, I know this post is from 2 years ago...but did you solve the problem?
Next time, I would suggest to use screen recording software.
And thats how you change your vin number lol
can you also change the mapping ?
Not through forscan, it's just for control modules and not calibration tables.
Is ford cmax hybrid like ford focus?
When i open central configuration it give me stop safley now!
Give me your name on Facebook i want help
Focus Mk2,5?
on mk2.5 everything is much easier with ELM config.
@@miladinseratlic5984 what about focccus?
@@pedromonteiro2644 what about your question ?
@@miladinseratlic5984 was asking if you tried it, plus did you use an usb obd reader or Bluetooth?
@@pedromonteiro2644 i just said that comparing to forscan and this bcm access on mk3 focus it is much easier to do all this things on mk2.5 focus with SW called ELM config.
Focccus is for mk3 which I don't own so i couldn't try it.
I have USB type obd scanner and I recommend it over BT bcs connections is much more stable. You don't want anything to interrupt communication while writing to BCM bcs you could brick the module.
I hope that this is the answer you are fine with.
Ah yes, the foreskin forums.
alo