[@waqasahmadchaudhry1681]

Very Good,I am Electrical Engineer and have 10 years of experience,I appreciate your efforts for the engineers

[@SaeedAhmed-ix8nm]

One of the best explanation using ETAP software.

[@ismailbinmail1956]

one of the best explanation i found on youtube. Please sir, keep up the good work!

[@donaldhenderson5039]

Thank you Sir, very good instruction. I worked in Relaying field and am returning
Appreciate very much.

[@Josuedosawe]

Thanks man, ure the best !

[@rameeskr]

thank you very much.
please make more etap tutorials

[@nirajsolanki7853]

You make this topic very easy . Nice explanation. Waiting for more videos on relay coordination.

[@kilumumahesh935]

Well explained sir , before knowing the everything we must know the basics step by step .we Hope more ETAP software videos from you... Thank you...

[@gerardodepedro5420]

Hi Muhammad....Thank you for sharing you knowledge...

[@rassjnr]

Great job!

[@dilkibat4470]

thank you sir please make more etap tutorials

[@danishuddin5370]

Thank you Sir..😍😍😍

[@henryashilonu7144]

nice one. 👍

[@mafizurr]

Very much well explained with powerful presentation.Need the audio a bit more ....Please.....Thanks & Best Wishes

[@jishnunarayan6705]

superb

[@amanuelkachiko6010]

thank's

[@MathwithZ.Z]

thanks

[@onuroznalbant1067]

thanks for presentations.If ask a question about How we can do relay coordination and selection with graphics.Now I am designing a power plant what we 'll select?

[@egnlishlearningchannel2357]

hello i want know how relay setting are done in radial distribution system. Either it is done manually or any software available

[@anvargulomzoda5046]

Thank you very much Muhammad Hassan.
Can you show us how to prepare and run Real time?

[@ahmadbasil3714]

hello can you please let me know that how we will know that we have to set the pickup value 1.1 ?

[@raje1155]

👍

[@vaporya]

Please make a video about the operation between recloser,LBS and fuse

[@tanji8592]

I add a solar panel on the distribution bus but why the solar panel always in overpower condition in load flow analysis ?

[@nchimunyamuyuni7920]

How do I add a rectifier to my single line diagram?

[@cstorvold]

Hi, When I set up the transmission line parameters and press ok, it does not save the information. Can you tell me the reason? Thanks.

[@mikelennon1078]

When using ETAP for calculations like Voltage Drop, Free Air or Underground Ampacity Calculations, etc. Are result compatible with NEC only or other ones as well like Canadian Electrical Code ( CEC), or ....... How we can select either US or Canadian or ,,,,, other codes and standard and /or how do we know which one/s the calculations are based on? Please advise.

[@PTIrealsupports194]

Hi
Have you any video for Relay coordinations?

[@boongboong3199]

I want to setting intertrip from cb1 to cb2, i mean cb1 tripped by ocr1 then send a signal to open cb2. how can i do? Anyway thanks for your video

[@rajkumar-ms1iy]

great video
but sir relay settings are getting saved what to do ? I'am not able doing relay operation.
do help

[@engrmuhammadsamiullah6010]

Sir I have a question related to svc rating
Sir svc ki capacitive AR inductive rating Ka kesy find krty hein?
Hamein svc ki capacitive AR inductive rating Ka kesy pata chly ga k ketni put krni hai AR kesy nakalni hai

[@muhammadsyafiq98]

I cannot get same result in short circuit. Why ya?

[@kamal7757]

hello where can get this etap

[@shai746]

Well done for the video. Please the clicking sounds is very unpleasant. Next time check that sound

[@sunillama1226]

While running a load flow analysis, it shows an error (the conductor/wire Y coordinate should not be zero). Can you please give an idea to fix these error?

[@Muhammad-Hassan]

Dear Sunil,
Please follow the instructions in the video, hopefully your error would be rectified.
- Check if have entered the parameters of the transmission line correctly.
or you can watch this video about load flow analysis.
czcams.com/video/LG2GqG75FZ8/video.html

[@mohammadusman3399]

check the impedance parameter, put value for "X" or "X/R" ratio

[@BB-de7ux]

Sir by etap we learn whole concept of relay or not

[@tasnimalam9256]

relay info is not being saved. any solution please?

[@hijaziahmad7417]

hi.. why do you set the CT primary as 300? can i have detailed explaination?

[@Muhammad-Hassan]

just an arbitrary value

[@donengo4617]

@@Muhammad-Hassan in fact you choose this value in order to avoid saturation of your current transformer

[@ArifulIslam-dy6jf]

after changing the relay editor data it is not being saved, any solution pls?

[@tasnimalam9256]

same problem for me

[@engrmuhammadsamiullah6010]

How to change the frequency 60hz to 50hz in etap.kindly explain

[@Muhammad-Hassan]

Go to project menu and then select standards, there you will find the frequency settings

[@engrmuhammadsamiullah6010]

@@Muhammad-Hassan thank you

[@nongskirt]

Link where to download hehe

[@ayazmahmood3496]

Heh i am interesting in trainings with you how to contact or approcah you

[@hussainkhan-jq4nk]

thanks

[@belaidimohammedamine3411]

thanks