HI Vikas, Very glad to see, someone having a through knowledge of porotherm building constructions. This is in mind for long time for my future home, but usually its either karnataka or kerala based videos that would come on the search, and little surprised to see someone near my native. Good job.
I am a civil engineer with 30 + years of field experience. I have used lime mortar ,cement, clay bricks, flyash bricks, AAC blocks, cement hollow blocks, Porotherm, over these years. Porotherm is NOT as great as it's made out to be. Concealed wiring , plumbing and handling ( without gloves) is a nightmare. The best I have found is good quality Chamber bricks that we should bring to site and used only after two weeks, to reduce thermal shrinkage, and we'll soaked for an hour in water. AAC is far superior to Porotherm, easy to handle. Concealed wiring and plumbing no problem. No need for internal Plastering..direct cement based putty on walls..huge savings in money and time!! Even lighter than Porotherm, masons can easily pick up the skill to lay. Cutting of blocks and wastage compared to Porotherm is minimal. Regarding insulation..that a lot of hype. Always have vents at roof level with openings that have taper outwards to allow air to flow out at roof level. If you can make similar vents near floor level, with opening that larger taper inwards, cold air will come in naturally. No need of AC.
Porotherm bricks or interlock blocks இந்த ரெண்டுல எது பெஸ்ட் 3 floors building கட்டுவதற்கு எது சிறந்தது எது அதிக வெப்பத்தை கட்டுப்படுத்தும் எது cost குறைவு
Hi satham, thanks for reaching us, see it is basically based on the requirements , location you are going to construct, purpose and output of your building. By knowing all these details in mind we can suggest which is good and bad.. for further details you can call to 99943 99933
We are constructing 1st floor of our home so veetukula just oru 2 (10*10) walls ku matum use panalam nu iruka oru different look kaga athuku ethu best VP or HP and stone oda colour marama iruka what colour I should choose to paint over that suggest me buddy
You can use VP for load bearing structure where you can save money too. stone oda colour marama eruka use teracotta exterior paint to have same look and free from algae formations
What is the diff between VP and HP. Can i use HP for load bearing.? Planning to rice a home in kerala. How they bonding the side of the brick, because there is already a cavity. Is there any chance of mortar wastage. Is cement mortar is enough for bonding? Where is the house that you shown on the vlog.?
J C hi sir, thanks for reaching us. HP Can’t be used for load bearing., while the VP can.. mortar wastage are not there. cement mortar is enough for bonding. House is in Pattukottai (Thanjavur DT)
Thiru B. Mudaliar hi sir, you can expect a variation up to 7 degrees. But we don’t have any test report for that.you can feel the difference if you visit our site too
Can you share the interiors of the house in your background...? Like how is the kitchen bathroom etc is designed ... so that we can get an idea on waterproofing, ceiling, plumbing n electricals. Thank You.
Hi Vikash, I'm Arun from Bangalore. I'm planning to extend my house at the 1st floor which approximately comes up to 765 sft. It is a load bearing structure. I would like to know what the cost of construction per sft would be with Porotherm blocks.
I should have named as associates sir. But in my locality name should b in Such a manner that even a common person should understand. I can’t be legal in this. I have to be with clients side for their better understanding
@@ReplicaArchitectsandBuilders you are at serious fault by naming yourself architect without coa registration,.. any architect can file a fraud and misleading case on you at first sight and you will be at serious trouble.
Yes sir, it can be used in load bearing structures too. Only thing you have to notice is there are 2 variants in Porotherm block (one for framed structure and another is for load bearing) so while you purchase be sure about it. thank you
To build For 1700 sq ft 2BHK house how much porotherm bricks required and single porotherm brick cost how much. If we'll not mortar the outside wall, it will damage im rain and sun ?can u pls advise durability of the house.
Hi, merely you will need 2210 bricks (full block 2000 + Half block 210nos). Cost varies - 76/- (approx) per block Half block - 40/- (approx) Always provide a small cantilever slab all over the building to avoid direct exposure of building.. providing a coat of water repellent or painting above porotherm block is better always
@@ReplicaArchitectsandBuildersthank you so much for ur reply. Can u please assist which brick is better interlocking bricks or porotherm bricks or AAC bricks. The same concept 2bhk.
Ranjith it all depends on your location, your budget and the type of construction you need.. So be sure about your geographic location to make sure about the building materials
Bro what will be the overall cost? I mean is it cost effective or not when we make a comparison with conventional building material(i don't know tamil)
Drilling பண்ணலாம். Heavy load ஆனா second cavity வரை drill பண்ணனும். Or preplan பண்ணால் எங்கெல்லாம் ஆணி அடிக்க வேண்டியிருக்கோ அந்த brick cavity யில mortar fill பண்ணலாம்.
@@ReplicaArchitectsandBuildersporotherm Bricks.. Is this brick suitable for ocean area's... 2nd question - Is this project done by you... 3rd - Yes we can discuss by tomorrow over phone call
aji jacob hi sir, have you seen the video ? We have said about the rates too.. more over people from different town askin about the rates.. It generally differs. pls watch video. Thank you
Super and clear explanation sir
HI Vikas, Very glad to see, someone having a through knowledge of porotherm building constructions. This is in mind for long time for my future home, but usually its either karnataka or kerala based videos that would come on the search, and little surprised to see someone near my native. Good job.
Hi sir, thanks for your valuable comments.. :)
Sir
Porotherm bricks home எத்தனை வருடம் உழைக்க கூடியது.
3 சென்டில் வீடு கட்டினால் எவ்வளவு செலவகாகும்..
Sir, we are planning to construct 2 flr. 600sq. Base floors were built in Normal type. Can we use these bricks for 2fr now??
Sir sivagangai district la intha brick kidaikuma sir
Contact number iruntha kudunga sir
Thanks. .
I am a civil engineer with 30 + years of field experience.
I have used lime mortar ,cement, clay bricks, flyash bricks, AAC blocks, cement hollow blocks, Porotherm, over these years.
Porotherm is NOT as great as it's made out to be.
Concealed wiring , plumbing and handling ( without gloves) is a nightmare.
The best I have found is good quality Chamber bricks that we should bring to site and used only after two weeks, to reduce thermal shrinkage, and we'll soaked for an hour in water.
AAC is far superior to Porotherm, easy to handle. Concealed wiring and plumbing no problem. No need for internal Plastering..direct cement based putty on walls..huge savings in money and time!! Even lighter than Porotherm, masons can easily pick up the skill to lay. Cutting of blocks and wastage compared to Porotherm is minimal.
Regarding insulation..that a lot of hype. Always have vents at roof level with openings that have taper outwards to allow air to flow out at roof level. If you can make similar vents near floor level, with opening that larger taper inwards, cold air will come in naturally.
No need of AC.
Your comments are welcomed. Thank you 🙏🏻
Sir, your contact number please
Good
It looks like during summer it will reduce the room temperature. But how does it work in winter in Tamil nadu.
General these bricks have the capacity to main good temperature inside the building in both the climates
Porotherm bricks or interlock blocks இந்த ரெண்டுல எது பெஸ்ட்
3 floors building கட்டுவதற்கு எது சிறந்தது
எது அதிக வெப்பத்தை கட்டுப்படுத்தும்
எது cost குறைவு
Hi satham, thanks for reaching us, see it is basically based on the requirements , location you are going to construct, purpose and output of your building. By knowing all these details in mind we can suggest which is good and bad.. for further details you can call to 99943 99933
Hi sir. Very useful video. Which is good for a 1000 sq ft load bearing house ? protherm bricks or laterite stone in terms cost ?
GOOD SIR
Naan oru malayali.vedeo nalla irukku.subs 👍
Thank you so much sir
Coimbatorela kattitharuvigala
We are constructing 1st floor of our home so veetukula just oru 2 (10*10) walls ku matum use panalam nu iruka oru different look kaga athuku ethu best VP or HP and stone oda colour marama iruka what colour I should choose to paint over that suggest me buddy
You can use VP for load bearing structure where you can save money too. stone oda colour marama eruka use teracotta exterior paint to have same look and free from algae formations
16*8*6 vechu oru chinna veedu pannalama
5 inch brick iruntha....inner walls ku use panallam ...so carpet area increase panidalaam
It is sir
AC Geyser...Loads thaanguma... oru video pota nalla irukum bro...Since its hollow doubt vardhu
Thangum bro.. sure I’ll do one video on that.. :)
Brother... plastering panna thermal insulation affect aaguma
What is the diff between VP and HP.
Can i use HP for load bearing.?
Planning to rice a home in kerala.
How they bonding the side of the brick, because there is already a cavity. Is there any chance of mortar wastage. Is cement mortar is enough for bonding?
Where is the house that you shown on the vlog.?
J C hi sir, thanks for reaching us. HP Can’t be used for load bearing., while the VP can.. mortar wastage are not there. cement mortar is enough for bonding. House is in Pattukottai (Thanjavur DT)
இது மாதிரியான வீடு கட்ட அரசு ஊழியர்களுக்கு அவருடைய துறையிலேயே லோன் போட்டு கட்ட approval உண்டா
I used this brick for my new house recently
That’s really nice.. May I know the feedback ?
What is the temperature difference? E.g. when outside temperature is 40 degree, what is the inside temperature???
Thiru B. Mudaliar hi sir, you can expect a variation up to 7 degrees. But we don’t have any test report for that.you can feel the difference if you visit our site too
Bro one brick how much price????
rubesh ganesh hi sir, it varies place to place. Starts from 72/- for our project
What the price per brick?
I think 90-100 including transportation
80
8 inch 92 rupees
How many Floor can be construct using this blocks
Until 7 floors
Can you share the interiors of the house in your background...? Like how is the kitchen bathroom etc is designed ... so that we can get an idea on waterproofing, ceiling, plumbing n electricals. Thank You.
Will do that asap mam
In pattukottai where it is situated tell me please...
Anaikadu..
what is the water proof solution used for the exterior wall?
Zycosil. It’s a water repellent compound
Where will we get this kind of bricks in Tamil Nadu , I mean in Tirunelveli
Hi leah, Call to 99943 99933
Thank you sir...intha bricks buying details sollunga sir..pls
Call affa tiles chennai
you are saying horizontal bricks are not for load bearing, but thats what you are showing, is that house built using a vp or hp brick?
What I shown is not load bearing. it’s a framed structure
Hi Vikash, I'm Arun from Bangalore. I'm planning to extend my house at the 1st floor which approximately comes up to 765 sft. It is a load bearing structure. I would like to know what the cost of construction per sft would be with Porotherm blocks.
Sir , Kindly call me for porotherm samples and demo. We're available in Malleswaram and Indiranagar. Contact me at +91 97411 99293
Hi Arun. for construction you have to use VP type Porotherm block.. Construction cost it ranges from 1750/- per square feet for load bearing
Brick price enna
Price
sir, please use a mic as we find it hard to hear.
How about the nails (Aani adikalam)
Yes we can do that in between the mortar between 2 Porotherm
If there is no plastering, wouldn't it cause cracks or wear & tear?
No cracks. It’s better to be exposed
Could not understand the language but too good
Thank you sir. What’s your language.
@@ReplicaArchitectsandBuilders English but worked in Gulf so had lot of keralite friends
Please search in web which is World's oldest language
That language this host is speaking
@@thalmada7686 really
Hi. Laterite stone or porotherm which is best in terms of cost for a 1000 sq ft exposed house for erode.
Go for Porotherm
Without plan.. It’s tough to provide cost
Portherm brick erode enna cost varum
It starts from 72/- sir per block
Cost using this brick for 1000 sq ft house?
Hi Vikash.. you are civil engineer, how can you name your firm as architect and builder?.. have you got coa registration or what?
I should have named as associates sir. But in my locality name should b in Such a manner that even a common person should understand. I can’t be legal in this. I have to be with clients side for their better understanding
@@ReplicaArchitectsandBuilders you are at serious fault by naming yourself architect without coa registration,.. any architect can file a fraud and misleading case on you at first sight and you will be at serious trouble.
Interlocking or porotherm brick which one is best for room temperature, durability, as well in budget segment
Hi praveen Kumar, best for room temperature Porotherm, economic is interlock
nice
போரோத்தம்.செங்கல்.எங்கு.ககிடைக்கு.நான்.சென்னை.வெளிபுறம்.பூச்சி.தே வையில்லையா
Chennai Affa tiles (google pls). Plastering is based on our requirement sir
Bro 8" la column design panni panlama
Yes
Can we hang Split AC in this Porotherm block built wall?
Yes offcourse we can.. as we fix WC.. anchor bolt has to be used blend with chips concrete., after fixing a day after you can hang the AC
@@ReplicaArchitectsandBuilders is there any demo available for this? I have searched but didn't get proper example.
Ok we will carry out an example and provide you. thank you. Be in touch
@@ReplicaArchitectsandBuilders Sure waiting for you new video.
Intha bricks cost evlo?
Load pering veedu la first floor kattalama intha brick la
Bharathi raja hi sir, there is another type called VP.. you can use that
Sir I'm from Sivakasi. I want masion to build my outer walls with prothom bricks i want the same finish as if in the video. Is it possible to do.
Hi, sure we can. quite conditions are there too. Reach us at 99943 99933 to know more sir
Udumalpet la iruka... I planning to build house ...
Eruka nu therila.. oungaluku theva patta kandipa call pannunga arrange panni tharom
Can we plaster? Plastering which material best?
Sure if we need we can
@@ReplicaArchitectsandBuilders cement or pop
I live in pudukottai send your phone no thankyou
world biggest ship Jayanthisrinivasan 99943 99933
Northern block erode la cost enna varum
Anna this house oda sqft and construction cost share panna mudiuma
Sure kindly contact directly
Ithu la kattuna 1 sqft ku evalavu varum
Volum. .......
Can these be used for outer walls or can it be used only for inner walls which divides the rooms
can be used both
It can be used in load bearing structures or framed structures??
Yes sir, it can be used in load bearing structures too. Only thing you have to notice is there are 2 variants in Porotherm block (one for framed structure and another is for load bearing) so while you purchase be sure about it. thank you
@@ReplicaArchitectsandBuildersok
Bro nanum pattukkottai tha, intha veedu pkt la enga irku ?
Anaikadu
Anikkadu and sivakkollai
Andhra Pradesh la vidu kattunam20×25 sq cost eavala aagam
Requirements and pls contact number if you are serious in construction
To build For 1700 sq ft 2BHK house how much porotherm bricks required and single porotherm brick cost how much. If we'll not mortar the outside wall, it will damage im rain and sun ?can u pls advise durability of the house.
Hi, merely you will need 2210 bricks (full block 2000 + Half block 210nos).
Cost varies - 76/- (approx) per block
Half block - 40/- (approx)
Always provide a small cantilever slab all over the building to avoid direct exposure of building.. providing a coat of water repellent or painting above porotherm block is better always
@@ReplicaArchitectsandBuildersthank you so much for ur reply.
Can u please assist which brick is better interlocking bricks or porotherm bricks or AAC bricks. The same concept 2bhk.
Ranjith it all depends on your location, your budget and the type of construction you need.. So be sure about your geographic location to make sure about the building materials
intha brickla katuna veedu Oru Vedio podunga bro
Hi Karthik.. sure we will post video of house made in Porotherm
Bro what will be the overall cost? I mean is it cost effective or not when we make a comparison with conventional building material(i don't know tamil)
Hi thanks for reaching us.. It’s depend on the way we built our house.. reach too 99943 99933 for more details..
Is it available at Madurai area/Tamilnadu?
Can it be used in load bearing structure
Sure, there is another variant used for load bearing
@ZERO TO INFINITY sure I’ll
Sir etha porathal.yanaga kadikum sir iam Nagapattinam
watch video again pls
Is it available in pondicherry bro
Yes it is, reach us at 99943 99933
Is it available in Idukki district?
I don’t think so.. if you need we can arrange from our side
wienerberger.in/authorised-dealers.html
ponkunnam dealer is there i think
Three cent la house katta cost
Then ithula kattum pothu 1 sqft ku evalavu cost varum sir
Pandian Porvel hi sir, it’s upon your Requirments.. rates can’t be finalized roughly
Hi sir a am also pattukkottai. I would like to see this construction. can I know in which place at pattukkottai.
It’s in anaikadu
Rate ????
Please check our comment sections..
ஆணி அடிக்க முடியமா?
டைல்ஸ் ஒட்ட முடியுமா?
Drilling பண்ணலாம்.
Heavy load ஆனா second cavity வரை drill பண்ணனும்.
Or preplan பண்ணால் எங்கெல்லாம் ஆணி அடிக்க வேண்டியிருக்கோ அந்த brick cavity யில mortar fill பண்ணலாம்.
Hi, Thanks for the reply JC
Yes panlam, Anchor bolt use panni, Concrete oda pack panna better
விலை என்ன bro
75 plus gst
@@ReplicaArchitectsandBuilders இராமநாதபுரம் மாவட்டம் அனுப்புவீங்களா ! பிரிக்ஸ் எவ்வளவு செலவு வரும்
Hi.. will u accept project in nagapattinam..
Sure sir, we will.. contact number : 99943 99933
@@ReplicaArchitectsandBuilders.. Hi.. what is your view. Is this brick suitable for ocean areas.. will this witstand insect attack
karthick Raja hi sir.. What kind of brick you are asking ? Possible to have a call tomorrow?
@@ReplicaArchitectsandBuildersporotherm Bricks.. Is this brick suitable for ocean area's...
2nd question - Is this project done by you...
3rd - Yes we can discuss by tomorrow over phone call
karthick Raja thank you :) yes that project done by us
Ji rain season how to safety in this brick
no issue sir
Going 2 construct First floor using this porotherm. Can I use Porothem HP?
Hi sir, thanks for reaching us.. offcourse you can.
Thank u. Please note it is masonry structure with RCC roof.
Noushad Ch Are you saying that is that an load bearing structure ?
Yes. Its a load bearing structure
Noushad Ch what kind of bricks you have used in Ground Floor, what type of soil you have (any brief details about that ? )
750 feet house how many need bricks?
Approx 860 bricks
Cost for 1 ps
Now it is 85 plus tax
What is the average cost of one such brick? Thnks
ப்ரோ ரேட் எவ்வளவு சொன்னா நல்லா இருக்கும்
It is nearly 80 rupees
Thiru B. Mudaliar 76/- (inclusive of transportation,unloading and GST)
Thermo bricks one piece how much price?
110 to 120
Audio not clear
Will rectify
Ur backside house total cost bro
Hi Dinesh, sorry I can’t understand.. you need total cost of which house ?
@@ReplicaArchitectsandBuilders intha video la back side la oru house kamchingala athota cost
Dinesh kumar hi, building cost alone 70 lakhs (4000Sq.ft approx)
1400 sq feet ku evolo cost varum porotherm vechu build panna
Dinesh kumar hi, I need plan to see to say the approximate rate.. Reach us on 99943 99933
I’d like to construct a commercial building 60X90 with steel roofing, location Tirupur, what would be the cost of total project
Hi sir, have u done any plan for that..
Where are you
I’m near mani koondu (Replica studio)
bro intha brick enga kidaikum. thanjavur near Anu place. 22*42 evalo coast aagum bro. ithu pillar potta veetuku thana set aagum
Kindly contact to 99943 99933 for more details
@@ReplicaArchitectsandBuilders why you not mention the price people want know ?
aji jacob hi sir, have you seen the video ? We have said about the rates too.. more over people from different town askin about the rates.. It generally differs. pls watch video. Thank you
@@ReplicaArchitectsandBuilders yes okay kindly can you mention your own place price
aji jacob 76/- (inclusive of transportation,unloading and GST)
Thiruvarur price
Can u plz expalin in english
Yanna Rs.....?
75 + GST
Brick rate
Sadham Hussain .B.E 76/- (inclusive of transportation,unloading and GST)
I would like to have my own 2 bhk with plinth areas 500 sft . Will u provide mason and how many bricks needed for it.
Thirupathi Reddy hi sir., for 500sq.ft you will require 580bricks..sorry currently we don’t supply masons.. we are total contract people.. Thank you
Sir, 580 bricks mentioned is for constructing 500 sft plinth area .or wall; kindly confirm. In case I bring my mason will u guide him.
Thirupathi Reddy kindly give a call to 9994399933 tomorrow after 11:30AM
GOOD SIR
Will it gives same strength of Red brick?
Hi, At some part it varies. Durability is good compare to red bricks.