POWER STEERING PUMP PULLEY REMOVAL
Vložit
- čas přidán 30. 06. 2024
- Thank you for watching 2Carpros.com. In this video we show how to remove a power steering pump pulley on all cars.
www.2carpros.com/articles/remo...
If you have any questions please visit www.2carpros.com/questions/new where we will answer any questions you might have.
Please use all safety precautions. - Auta a dopravní prostředky
You were the only one to mention the proper depth good job!
Good to see it being done while on the engine in the complete vehicle. This has been my strategy. Also appreciate the info of the two surfaces being flush as confirmation of being completely on.
Excellent video man,very well explained and some nice quiet background music to go with it, don't understand why some people want to explain something to you while playing heavy metal in the background at 300 decibels.
Great vid, little late for me on the heated pulley, I struggled getting it back on new pump.
Took me a minute to find this but this video was a HUGE help thank you SO much
wow i was having the same problem with my sleeve, the hose clap was a great idea. i am going to try it. thanks for the video
Same problem with the tool slipping off had me searching the net for a solution. Found it here with the band clamp. Thank you!!!
Very helpful. I won't say I was lost but I knew I needed some special tool.
Good job...clear, no bs and to the point!!!
Thanks for watching!
Thank for keeping it short n simple ! Thank man
No problem!
Best vid explained in full details. Thanks guys
Thanks for watching!
Thank you broh I did so well in my truck thank you so much..
Great vid very simple to understand
Thank you for watching!
extremely helpful. thanks guys.
Thank you so much for watching!
OK, aint gonna sugar coat it. I just finished this job on my 4.3ltr S10. It's a bear. Forget put pulley in the sun or heat gun. Use a propane torch. But first, get a large pair of vise grips and grind them down so that they are slightly thinner than the hub. You have to be able to grip hub but still have a small clearance for tool to get flush with shaft/outer edge of hub. Heat hub for 4-5 minutes. Get a good grip (not extreme) on the hub with V Grips. Find a pipe to put on thumb screw of vice grips for cheater bar purpose (I used a hyd bottle jack handle). Use large adjustable wrench (Crescent) on large nut on collar of install tool. Wear gloves. Never would have believed it would go on harder than it came off but got it. A few teeth marks on hub but strap wrench I had was too small and don't know if it would have held anyway. Geez. Good Luck.
make a video on it good sir
@@xesberto937 Yeah, sorry. That was 3 years ago and I remember it fought all the way, but I can't figure out what I was talking about in what I wrote either.
The jist is, when installing the PS pump pulley. Heat the center hub of the pulley, I tried a heat gun but it didn't get it, use a propane torch. But before you start, go through the whole process in your mind and have all your tools at the ready. Seriously, take a dry run before you heat it. When you take it off the heat you have to move fast. You have to be able to screw down the install tool but not have the pump turn. It's like trying to wash 3 cats at one time and 1 of them will burn the shit out of you if you touch it all while applying about 125ftlbs of torque. All while standing with your head upside down. Make sure you have your light situated just right so you can see well while doing this., you don't have time to go chasing it if you knock it down. Make sure it's out of the way and secure. Thick welding gloves, safety glasses and all the determination and umph you can muster. Good Luck Alberto. Lemme know how it goes.
Thank you you guys help me a lot
Thank you for watching!
Awesome and great video
Very helpful. Thanks.
Good thinking on the gear clamp.
how do i remove even the little tank and the rest of it on jeep liberty 06 ? do you have a full video ?
Really good explanation in video brother....
Thank you so much 🙂
will this worrk without the wrench to keep it from turning? i have the 5/8 tool but no wrench
Does the reman pump have the same light steering as the original pump? I put 3 reman pumps in my 06 Corolla because all the reman pumps make my steering heavy. Should i just rebuild my original pump???
Hi, if the pulley is not flush with the inner surface, does that mean it not tighting all the way or you have a bad pulley, pump bearing?
Thanks a lot
How you get the cap that’s on the pulley off covering the bolt?
Thank you for this I thought I had to take the pump completely out to put on a new pulley.
i have a problem on my nissan sentra supersaloon pulley. it is croocked and pulled out of line makes a squeaky sound and i think its detrimental to engine. what do i need to do?
thank u very useful video
Thank you for watching!
The reason you need to pull the pulley is because your new pump comes bare! No pulley! Remove old pulley so you can put it on new pump BEFORE you give the parts store your old pump as core. Just borrow their tool while there...come back with core and tool for credit back for both!
+sam k Nice tip, thanks!
I replaced the power steering pump assembly on my 2001 Oldsmobile Intrigue, put the pulley back on, and currently, it's wobbling. The pulley is flushed to make ends meet, and I don't understand why it's doing that. I had a coolant leak previously and fixed that last week, yet it still wobbles a bit and squeaks/chirps. Should I install a new belt, idler, and tensioner pulleys?
How did you get the pulley to stop wobbling? 🤔
Quick and simple I like it
Thanks for watching!
What do you do if pully shaft an pully both came out?
Will this work for a 07 Chrysler Sebring?
This works for all cars, Mercedes and imports too?
is this the same process on most vehicles
super good, ty
Thank you so much for watching!
nice video thanks
Thank you for watching!
After having a pump replacement ,started 2 get the cricket sound loud and clear, how 2 rid of it is the question?
Pulley just spins with the tool o there any help?
need to know how to remove and replace the power steering pump on a 2005 chevy impala
+valerie godfrey Our experts will be glad to help, please use our free question form so they can reply to your question personally.www.2carpros.com/questions/new
@2carpros how do I replace power steering pump and alternator on 1999 Mercury sable dohc ... I can't find any videos or help
+brandon marshall im sorry we don't have that video yet,
Do you have vidoe of removing/replacing the power steering pump?
Got you covered! czcams.com/video/EXDysSOs07g/video.html
Thanks for watching!
How did you loosen the belt
I saw a video of a guy installing a power steering pulley & he said put a little grease on the shaft before installing is this a good idea ?? If it is a good idea can I put wheel bearing grease on the pump shaft ?
Bad idea! Never ever ever put grease on it. It is supposed to be a hard pressed fit. If there is grease on the shaft it can cause slippage or worse fall off while driving. Thanks for watching!
Hi, 2CarPros I have a dodge ram 1500 mod 99, is making a noise, so i change the tensioner pulley, but when i was locating the band, i so that the steering pulley has a movement, like it's a little loose, do i have to change it, or a little of movement its normal on it, thanks for the help
PS pulley should be very tight on the shaft with no movement between them whatsoever. Pulley should not wobble when spinning on shaft.
How did you put the belt
this looks like a Chevy blazer/jimmy/bravada in case anyone was wondering
great video, but do we ALL have to use our air ratchets as a manual ratchet for this, or would it be cool if I hooked up the air and saved my wrists all of that hard work? Sorry, I just had say it! Seriously though good video!
My air ratchet didn't have enough power at first. So I had to do it manually. Thanks for watching!
@@2carpros I appreciate you posting a video that actually helped!
Is this a 2008 chevy avalanche ? And whats the correct name for this tool so i can order it . Great video !
It is from a 2007 Tahoe but it is all the same. That is a power steering pulley removal tool. Thanks for watching!
Harbor Freight. About $13. Not a great quality tool but will work if you use heat gun or propane torch on pulley hub before reinstall.
@@2carpros how to get the belt off/ on
I don't understand how the bolt and nut tool install both are right hand, some times the power strering shaft start rotarig when the pressure resistance between the shaft and pulley is grater than the torque on the bolt screwed in the shaft. For me the best tool should be one end rh thread bolt and the other end lh thread with the rh thread nut. Just saying
Sorry LH THREAD NUT
I know what you mean!! I thought the stud was left hand thread and the nut was right hand. I would just end up unscrewing the stud or making the pulley turn. The way I solved this was to grip the pulley wyth my hand, turn the stud till it would reach the end, then ignore it and just turn the nut with a long wrench in yanking motions while gripping the pulley hard with the other hand.
Eventually you'll get to the point where you don't have enough grip strength to keep the pulley from turning, but by that time the pulley will be in enough where you can put the belt on all the pulleys and the tensioner will keep the PS pulley from moving and you can finish the job with much less stress!
Large strap wrench around pulley. Test all your tools fit before proceeding. Heat hub of pulley with heat gun or propane torch. Wear thick leather gloves.
@@SI0AX A hex head on the pulley hub would be nice wouldn't it.
will this work on a 2000 Chevy Malibu?
+gary robinson LOL I am here for my 2000 Malibu as well. Got in the car this morning and smelled a burning rubber smell and no power steering. Just looking to see what joy I have to look forward to this weekend. This will be my first power steering pump replacement. :-)
W202 Cdi220 diesel . Power steering pulley .
Help . Does it screw off or require the tool .
Got it off . A good screwdriver and slowly prise it off .
that tool should come with a collar that goes around those two pieces then no need for that hose clamp. Most sets come with that collar except that piece of junk. But gotta do what you gotta do
The hose clamp works much better. Try it before you knock it.
How do you remove the pulley on the power steering pump of a 2003 Infiniti G35 Coupe 3.5L? It doesn't have the port up on that extends out so is it just pressed on or what?
Yeah pulleys are typically pressed onto the shaft. Thanks for watching!
@@2carpros ok so they can't be removed and pressed back on?
No they can be you just need a power steering pulley puller and installer. You can usually rent them for very cheap at a local parts house.
will this work on my 1997 ford Taurus?
+James Carlos Rivas Fuentes Yes this will work for your Taurus.
Do you guys or anyone who sees this, an instructional video on how to take off a power steering pump from a 2001 Chevy venture van? Any help would be appreciated!
We are in 2018 & the vehicles manufacturer still building the same presidure. Isn't be more E-Z to to thread the pump shaft n put a nut???
Because it is cheaper and faster to press it on at the factory then take the time to make a thread. Thanks for watching!
No. Factory doesn't give to shits about what's easier for mechanics. That's been obvious for decades on all Manufacturers. The clutch fan on my Chevy truck is threaded on and it's not really easier to remove anyway.
How nice to have a pulley that just comes off and isn't completely seized to the pump so the shoulder that the puller attaches too just cracks off lol
My 04 envoy power steering pump has an Allen Screw in center of pulley. must I remove this first?
+mgoodell76 that is not an Allen screw it is just the front of the shaft, the pump pulley must be pulled off much like the video above.
Oh shit! No wonder I couldn't budge it last night. I feel like a dumbass. Tyvm for help. And great video!
The pulley on new pump is slightly bigger. Got belt on but 1 rib broke shortly after driving for a bit. Hoping a bigger new belt is answer.
+mgoodell76 that is not an Allen screw it is the end of the shaft you must use a puller like the one in this video
Why in the world are you using a pneumatic ratchet ?
Then, we see you using a flex-ratchet ?
Neither of these two ratchets are the "proper" tool to be using IMHO.
A straight ratchet (on swivel or flex) would be the preferred tool.
This video shows the basic procedure, but I'm experiencing something not covered here.
My pump shaft keeps turning while I'm ratcheting my installation bolt (Installing the pulley) and this causes my installation bolt to unthread from the shaft, prior to the pulley being fully pressed on.
Anyone else have this issue ?
Thanks for the video dude.
Do. I. Remove top. Mother mount
Nos gustaría ayudarle a qué es lo que están tratando de eliminar
+2CarPros
¿Qué le gustaría gustaría eliminar ?
+2CarPros mi carro tiene un resumbido,pero la diredcional funciona muy bien' sera la pompa de la diredcional
The lunch lady called and she wants her gloves back!
She can't have them. They are mine. Thanks for watching!
yea I'm fixing one for a friend
+gary robinson nice how did it go?
how do I know if the pump or the pulley is bad
Megan Torres The one on my 350sbc wobbles while idling and chatters while driving
When I try to install the pulley back in, it stops halfway through and i noticed that the threads on the installer are stripped. Any ideas how to fix this?
I'd try an other installer then. The first one we tried also stripped but that was a cheap knock off one. So we got our better one out and it worked great. Thank you for watching!
2CarPros I tried another one and I wasn’t as forceful this time and still stripped. I stopped before I stripped more threads.
Not all cars are this same way.
Not necessary for the most part these days. Usually now, you can buy a pulley and pump together and just pull the whole thing out, and replace!
The bolts usually won't go in or come out with the pulley on. They are in interference with each other. Thanks for watching!
HELP! I need to remove the retaining bracket mount. do I need to remove this pulley? I don't have this special tool.
+Mr. Woofwoof Head down to your local auto parts store where you can rent the tool.
2CarPros I managed to borrow one from a friend.I took the pulley off without any problem but when I tried to put it back the bolt that screws in the steering pump shaft( the one that forces the pulley back into place) won't hold. I live right on the Texas coast and rust is a big problem down here. I believe rust ate the thread and I could only manage to force the pulley so much before the thread gave away, I still need about a quarter of an inch til flush. What should I do in your expert opinion? Should I get a new steering pump?
I used the tool and took the pulley off and now I can't get it back on mot enough room
I would put it back on the pump and install them both together
Why would you replace just the pulley?
You wouldn't, but you have to pull the pulley off on some cars to get to the water pump bolt. That is right behind it. Like on the 95 z28 camaro. With the lt1 in it. Hope that helps.
***** most new pumps don't come with pulleys, gotta use the old
+Adam Davies the pulley can go bad!!!!!!!
Mine has a nut on the list outside
I bet that puller was a performance tool puller and yeah they are garbage
👍👍👍👍👍🍺😎
cómo lo quito de un mustag gt 5.0 94
useless for my car...Stratus rt
Speaking of useless Stratus RT
Not even close to this easy spent 7 hours trying to pull one off with this stupid tool went and got a 3 jaw puller and it was off in 5 minuets. Junk puller set
Took me 6 minutes or so with this tool. Thanks for watching!
All these Lil special tool 🙄🤦🏾♂️
Sometimes you need them. Thanks for watching!
@@2carpros really though. Not having That pulley remover took my last breathe that day
First things first WHAT kind of car are you fixing??? Thumbs DOWN!!!
Thanks for the thumbs down my man. Its any GM truck from the mid 2000s. They are all the same. All power steering pulleys are taken off and put on the way. The make and model doesn't really matter.
wow i was having the same problem with my sleeve, the hose clap was a great idea. i am going to try it. thanks for the video