Hi do you not torque the wheel bearing down? reason i ask is i have had 2 front wheel bearings fail, i dont know what is causing it, i have changed the driveshaft im thinking maybe wrong cv joint would this cause the bearing to fail? also do u not tighten the bearing with wheel on ground? or is there no need on this car. thank you
You will hear a humming noise which will get louder as it wears more. As you corner the noise increases as the load changes. Jack the vehicle up and spin the wheel...then touch the suspension spring with your finger...you will feel a vibration through the spring if the bearing is worn.
I recently did my Citroen C4 which shares the same suspension, brake and steering components, as your 307. Did you end up replacing the transmission oil that leaked out? I also had leaks but I'm thinking if I should replace it, I maybe loss 100ml-200ml of oil approximately
Hi bud. I see your well versed on Peugeots by the looks of things. Can you tell me how much gear oil a 2016 Peugeot partner 1.6 would take in the gearbox?
Not bad but important small things are not shown or just bad (e. g. do not mount the brake rotors with the small screws until the axle nut is tightened)…
brilliant illumination and filming! And I also like, how your children always find their way into the video 😀
Well done. That was a larger operation than I thought.
Einfach hammer deine präzise Arbeitsweise 👍💪
The Old Tappered Bearings are a joy to do compared to these ones!🙈
How big is the disc you use to push out the bearing?
Really good Video, thanks,
Thanks for the video now I can replace my
Hi do you not torque the wheel bearing down? reason i ask is i have had 2 front wheel bearings fail, i dont know what is causing it, i have changed the driveshaft im thinking maybe wrong cv joint would this cause the bearing to fail? also do u not tighten the bearing with wheel on ground? or is there no need on this car. thank you
good job!
Cheers mate
Good Vid but could have been better if you gave the spanner/socket/torx sizes
Great video
Good video! What are the signs of a bad wheel bearing and is there a test I can do without having a lot of tools?
You will hear a humming noise which will get louder as it wears more. As you corner the noise increases as the load changes. Jack the vehicle up and spin the wheel...then touch the suspension spring with your finger...you will feel a vibration through the spring if the bearing is worn.
excellent travail! bravo
Good Vid!
Just before fitting brake calliper, your thinking of a cup of tea? 👍
Good job
I recently did my Citroen C4 which shares the same suspension, brake and steering components, as your 307. Did you end up replacing the transmission oil that leaked out? I also had leaks but I'm thinking if I should replace it, I maybe loss 100ml-200ml of oil approximately
You can replace or you can just top up that is up to you
Can this be done by keeping the oil in gearbox? I noticed slight shaft movments make it leak, and gearbox is sealed for life unit on my 3008
It can be drained if necessary and refilled through the breather.
Rewelacja
👍
Hi bud. I see your well versed on Peugeots by the looks of things. Can you tell me how much gear oil a 2016 Peugeot partner 1.6 would take in the gearbox?
1.75 lt
@@guddupappu3582 thanks alot my man.
Please put part numbers and links in your descriptions.
Hi very good video, 1 question, in the whole item you took of were would you find the abs magnet ring, thanks in advance.
Magnatic seal on the bearing itself
Thanks for the quick reply, much appreciated.
Combien de Tonne presse svp?
Nice job, But never press from the inner race as you can ruin the bearing.
What wheel bearing brand do you use/recommend?
I will recommend Skf or NTN
What make is your 12 ton press
Bought from ebay unbranded
Not bad but important small things are not shown or just bad (e. g. do not mount the brake rotors with the small screws until the axle nut is tightened)…
How much Ton have your Wheel Bearing Press?
12 tons
@@guddupappu3582 Thank you man. You working perfectly, super Video 👍
Thanks
Very dangerous to use the grinder in that way..
Your finger soo closer to the angle grinder.you been so lucky.
But anyway nice video