Spektrum Quick Hit Tech Tips - DX3 Smart AUX Setup for Dig, Winches and more
Vložit
- čas přidán 30. 06. 2024
- In this video Tom walks our fellow RC enthusiasts thru the different Auxiliary Channel modes on the Spektrum DX3 Smart and how to use them. This is a great video for those with crawlers that include the DX3, like the Axial SCX10 iii, Or those looking for a extremely capable, yet affordable, 3 Channel transmitter for there crawlers, scalers and bashers.
In this video we cover how to setup a 2 position momentary switch which is great for setting up the Dig servo in your crawlers and scalers. Here is a shortcut to that section - 1:40
Then we cover setting up a 3 position momentary switch, which is great for winches. Here is a shortcut to that section - 5:48
And Finally we go over setup of the 5 Position Latching mode. This mode is likely the most versatile because it can be used for a 2-5 locking positions, 2 being perfect for ON/OFF functions like lights with controllers and locking functions like 2 speed transmissions. Here is a shortcut to that segment - 8:00
One thing we want to stress is that you make sure to rebind your receiver after doing this type of programming. This is so that if the rx goes into failsafe, that it does not force the servo into a position where it is binding up and damaging the servo. Also note that failsafe positions are the position that the receiver will go to when you power on the receiver without the transmitter being on first :)
Thanks for watching!
Make sure to follow us on Facebook and Instagram for all Spektrum News and Promotions!
/ spektrumrc
/ spektrum_rc
@SpektrumRC - Jak na to + styl
In this video Tom walks our fellow RC enthusiasts thru the different Auxiliary Channel modes on the Spektrum DX3 Smart and how to use them. This is a great video for those with crawlers that include the DX3, like the Axial SCX10 iii, Or those looking for a extremely capable, yet affordable, 3 Channel transmitter for there crawlers, scalers and bashers.
In this video we cover how to setup a 2 position momentary switch which is great for setting up the Dig servo in your crawlers and scalers. Here is a shortcut to that section - 1:40
Then we cover setting up a 3 position momentary switch, which is great for winches. Here is a shortcut to that section - 5:48
And Finally we go over setup of the 5 Position Latching mode. This mode is likely the most versatile because it can be used for a 2-5 locking positions, 2 being perfect for ON/OFF functions like lights with controllers and locking functions like 2 speed transmissions. Here is a shortcut to that segment - 8:00
One thing we want to stress is that you make sure to rebind your receiver after doing this type of programming. This is so that if the rx goes into failsafe, that it does not force the servo into a position where it is binding up and damaging the servo. Also note that failsafe positions are the position that the receiver will go to when you power on the receiver without the transmitter being on first :)
Thanks for watching!
Where do I go for transmitter repairs ?
@@juddosborne305 Repairs are done either by a authorized retailer or in house at our service center.
SpektrumRC thank you, I just started the process.
So I set the DIG servo endpoints. Then I re-bind the radio and receiver. But then doesn't that reset everything? When binding I then reset throttle and steering limits too, or just bind then turn off? Thanks for this video and all your help.
Hello do you know what's the limit motor that I can use with this esc, I can't find this info anywhere, I want change the 35t but what is the limit motor on 2s and 3s in the firma 40 crawler esc thanks in advance
Great video, thank you for doing everything slowly, and explaining for us newbies. Now to decide if I want Dig, or High Speed on my Gladiator...
Thank you for the video. I wasn't having a good time with the printed instructions.
Bro...thank you! That made complete sense.... was totally wondering on how to do that.
Very useful information. Thank you :)
You failed to explain how to use it for lights and winches. The only thing you explained was how to set servo positions over and over again. I've got a warn winch, how can I plug it in and get it to work? I've tried but no luck
I'm trying to straighten out the rear axle on my 4ws capra so this was helpful
Thanks for the help great video
I purchased a complete electronic system/package which i paired with a spektrum sr515 5 channel and the 4ws settings on the dx5r is wack 😑 😒 😤 i hate having to use different remotes for my rigs but i wouldn't have been able to setup my endpoint adjustments without this very informative video thanks!
-capra 4ws with vanquish f9 portal axles f/r and vanquish transmission with 2 reefs 900smarts 🤘
Just finishing up a Ryft kit build and I couldn't figure out why my 2soeed didn't work. I'm guessing it's cuz I was in 2 position momentary. Hitting the bench this afternoon to get it worked out. Thanks for the help.
Good video, I follow it but somewhat is not working with thw winch on the 3rd channel
Is it the same procedure with the ESC annd reciever in one of the SCX10.3 RTR Jeep Rubicon? Wish you have shown it on the actual RTR itself .
Please, please add this info to the instructions in the SCX10 III RTRs. I burned out two dig servos not knowing this. Also, please post the DX3 / SPM2340 Manual on the Spektrum site. It is not there in the Support menu!
how about rear steer? 5 position latching? How do I set it to neutral to start? Thanks!
How to use this for lights?
I’m having a hard time finding a winch setup for the dx3 would you mind making a video on that?
nice video ,could you also give some tips on how to setup channel 3 for light. as on and off
If you set it up as a 2 position latching, that will do the trick. The instructions in the video should help you do so, but if you need more guided instruction, feel free to message us on instagram or facebook to chat. Thanks!
Is I light switch still needed to set this up for lights? Or does the controller take care of all that? Thanks
What kind of winch uses a three position servo? I see three wires going to the servo.
I am installing a hand break in my felony and I have it in my auxiliary three port. Will this process work for that or is it going to affect my steering servo. I guess my question is will it automatically recognize I only have something plugged into my auxiliary three or should I move it to aux 1
1
What about my end points on my kraton 8s the ends points need to be set right their off
Do I need the wired control unit to run my winch with this radio?
My transmitter going crazy after i accidently activate the latching mode on axial scx10 iii .. the servo ,steering trim and throtle trim doesnt work like normal even i do reset and calibrate, any advice?
Hello friend, I have a radio dx3 and in my arrma infraction 6s I will have moved some settings with the bluethoot module in the app, the problem is that when I detach the avc does not turn off and the wheels no longer turn, instead when I reactivate the avc is always active and the wheels instead turn, I can not detach the avc yes and mixed with the servo, Please help me.
Just so people know you can use 3 pos for rear wheel steering. Just set 1 to middle 2 for left and 3 for right.
How can you setup this receiver for 4 wheel steering? I would like to be able to turn it on and off and have the steering knob control both servos.
Not possible with the DX3, you need a programmable transmitter for that, such as the DX5C
Hello,
You did not show how lights that have an interpreter works with the A & B switch for this particular remote and receiver. Would you kindly show how it is properly done please. I have tried and to no avail the A & B switch does NOT WORK. The light is plugged into channel 3 and lights only toggle when I turn the wheel on the remote with the st rate at full right. Again, I see it can work but how do I designate the lights to the A & B switch instead of the steering wheel?
Are you using an AVC receiver?
@@SpektrumRCvideos same question and yes I'm using an avc receiver
@@Chrisjam86 did you find a solution yet? Im stuck haha
before i started anything the servo was responding but returning back to neutral. after i tried messing with the dx3 setup the servo doesnt even respond?? it is plugged into AUX1 on the Rx. this is the most frustrating crap ive ever seen. how do i get my servo to see aux1?
using a micro servo for 2spd on a Ryft*
Sounds like you started the process and did not assign a value for any positions. Try going thru the 2 position latching procedure once again.
Do u have to do it with out esc connected and do it with just a battery connected cause mine does not do anything when I turn on the esc for power cause I'm trying to program with using a 2speed trans I'm really confused try to program this any help would be appreciated
Not sure if I follow? First thing that comes to mind is that you should make sure the polarity from the esc to the receiver is correct
Thank you for the video, very helpful. Why, why, why isn't this done at factory instead of frying servo after servo before figuring out what's going on? Axial gladiator rtr I purchased was not setup that way out of the box, and nowhere did it mention to do so. Disappointing spektrum, Axial, Horizon . Luckily Horizon backs its products ...but easily avoidable altogether 😤
From our understanding it is supposed to be done out of the box BUT it is possible it has been overlooked at the vendor. Glad we were able to take care of and that you found this info helpful!
I had the exact same problem, purchased my gladiator a week ago and two minutes out of the box and running the dig servo quits and starts making a horrendous noise. Called up the shop and they said bring it in and we’ll swap it out but they have yet to receive any servos to replace it with. I feel like this is a known issue with that specific servo as there are forums dedicated to how bad that servo is. I have no issues with the rig other than that. Hopefully I can get it replaced and the end points set correctly
Hey buddy, your wonderful electronics ain't working. The steering rate doesn't move my servo in the aux
I got this DX3 transmitter and one day when I turn it on and then turn on my truggy. Suddenly the transmitter is having one light turning red/green blinking a lot and with this very annoying chirping music tone sound coming from it. Afterward, my truggy being to reverse and lost control. What is happening? During that time, there are other people running their RC cars already, and I'm around a huge rail-road train track as my environment. Just laying out the setting of the situation. If anybody can chime in on what's going on, that will be much appreciated.
I cant get into setup menu in my transmitter
Does the DX3 have DSC so I can connect things like TBS crossfire?
No it does not.
Im having issues with my radio... Trying to run a winch.. brand new out of the box it was working fine like i wanted 3 pos mono.. then it started acting up where id go to winch out and the winch would just take off... And id have to hit the button a few times to get it to stop... So i tried to go in and reprogram. And now when i plug up, the winch just takes off and gets no communication from the radio
Sounds like you might have the points mixed up, try a factory reset and reprogram the AUX channel. Hope that helps!
@@SpektrumRCvideos how do you factory reset it?
@@jessiechapman2345 Factory Reset Mode
Resetting the transmitter to factory settings resets the AUX
channel mode, the AUX channel point positions and the
endpoints of the steering wheel and trigger.
To reset the transmitter to the factory settings, power on the
transmitter while holding the steering wheel to full left and
the trigger to full brake.
Is this the same for a dx5c controller looking for help on my 3sp transmission truck
not exactly. I would check out this video. It features the DX5 Rugged and focuses on LED control BUT but the menu is essentially the same and should steer you in the right direction czcams.com/video/RjgbuEgF350/video.html
How many receivers can I bind to this radio? More the one model?
Just the included receiver, no model memory
Will this work on a different servo as well?
I would think it will work on any Servo with this radio gear set up
My dx3 gives me flushing red light wen turning on , wat is that???
Why does this have the 5 position but it couldn’t be put in the dx5 rugged. I bought one to replace the dx3 and it will be going back due to the poor options for rear steer without a pot knob or 5 pos switch setup like this
The number of available positions can depend on the function. For instance, on the DX5 Rugged, if you using the 4WS mixing you are able to assign up to 4 positions.
@@SpektrumRCvideos not I’m the same latching manner
@@SpektrumRCvideos but it’s not latching
What are you trying to do exactly?
You didn't explain on off led on third channel
How do we set up the 3rd channel for a winch on the STX3? The instructions do not say how to set a neutral position. When I set it up I either have the winch going out or in, I can never get it to sit still.
I'm trying to do the same were you able to figure it out
@@ryanhamel4458 Not yet. I’m going to try emailing customer support next to see if they can help. If I get anything I’ll let you know.
I just picked up a gladiator and I'm looking to put a winch on mine as well
Guess I'm not the only one who is having this problem putting a winch on this channel
es dificil configurarlo, mi vehiculo no avanza hacia adelante,,se mueven las ruedas delanteras,,y tiene reversa, no avanza hacia adelante
Try the Factory reset function
Can i use the a&b button for led lights
If setup properly yes :)
@@SpektrumRCvideos how
Tried everything
@@miketube6662 Do your lights have a control box of some sort? If you are just plugging in leds into a rx port that is only providing power, you need something in between to interpret the signal and turn off and on the leds.
@@SpektrumRCvideos it has a switch to turn it on then u can press it again and again to get different colours then turns off after about ten colours
@@SpektrumRCvideos i do have a kill switch That goes to receiver and has an out for LED cable
How do you set it an ON AND OFF button 🙏
como se puede calibrar?,,,
Not helpful trying to program the aux button for a winch
I'm using a Android phone I went to the Play store but the app is not there for this unit
If there's app can you put the link