IR 2545 compressor Rings piston and head installed on this ongoing rebuild
Vložit
- čas přidán 23. 08. 2020
- In this ongoing series THE Guru installs the high pressure Cylinder, low Pressure Rings Piston and Cylinder and both High and Low pressure Heads.
thecompressorguru.com
compressor repair, compressor rebuild, compressor overhaul, compressor service,
Good duet between your wife and you working together, I wish I could do the same with mine 🤭🤐. “ paranoid live longest” good quote 😂. I’m working on my Curtis Toledo 80 gallon/dual stage 5 hp. Thanks for sharing your videos!
HI BUD I SPOKE TO YOU THANK YOU FOR THE INFORMATION I NEEDED ON MY COMPRESSOR PUMP CHANGE.
I HAVE LEARNED VERY MUCH WITH YOU. BLESS YOU
why did you scrap the rods for new ones not the case with the busted piston and rod but the other one ?
because the rod and bearing kit comes with new rods and crank bushing we were making this as close to new as possible . this pump goes in a factory where it runs non stop for 8 -10 hrs a day.
Hey, thanks for posting this series, I'm rebuilding a 2545 so it has been invaluable. On the pump that I'm rebuilding, the inside had a water/oil mix and rust. it had been sitting under a lean-to for a year or two. It is a 2018 model. Do you know how water would get in the pump housing? Maybe a bad shaft seal? Also to get the rust out of the housing I had to take it down to bare metal, do you know what type of coating I should put on the inside to prevent rust? Thanks,
Hi John thanks for reaching out. Please contact me through thecompressorguru.com I would be glad to work on a detail email to you. to long for this format.
What is the best suitable number for oil that will be used for 2000 working hours?
I use Amsoil 20W compressor oil. PCIQT-Ea is the part number. if you are in a hot environment I would use the Amsoil 30/40 compressor oil PCKQT-Ea.
Where do you buy your compressor pump rebuild parts from? Thanks.
we sell them contact me at thecompressorguru.com
Realy good
Hello what is the cost for parts for the same pump rebuild. Thanks
Hi James contact me through thecompressorguru.com I am happy to give you a firm quote. but in the mean time a complete rebuild kit is between 4 and 500 . because of the way the inflation is we check pricing before every quote. I will email in a price quote tonight so monday I can give you a firm price.
I am looking to get a rebuilt kit for an eagle gas air compressor pump 35 cfm 13G30TRKE-V4 do you sell those or what other info do you need to get the right rebuilt kit
I just found a picture of 1 of these this is a Saylor beal clone. I can sell you saylor beal parts but they probably wont fit. contact me through thecompressorguru.com and I may have other options for you.
@@THECompressorGuru if i send you picture through the email of the pump will you be able to say if they will fit? I am not really sure what is wrong with it, all i can say is that it did start making a bad knocking sound .
@@86lor send me an email but I am pretty sure what you have. It would help to measure the footprint hole spacing.
Question please engineer: Can this type of compressor handle 24 hours of continuous operation?
Yes. you should be changing your oil every 500hrs for regular oil. or every 2000 hrs with synthetic. make sure it is getting enough circulation( air movement) .
if you have any more questions you may contact me through thecompressorguru.com
Нет
Exelente job.., and realy , thank,'.
Hi sir, my name is fachrudin from indonesia..may i ask to you sir...can i know whats material did you use for bushing as compresor??thanks
Hi fachrudin thanks for reaching out. I am not sure which bushing you are asking about.
the Crank rod bushing is a machined steel. it goes on the crank shaft and the connecting rods go over it .
the wrist pin bushings are brass. I did not talk about these so I assume you are asking about the crank pin bushing.
our rod and bearing kit includes the new rods with the new wrist pin bushings. it also includes a new crank pin bushing roller bearing and the gaskets needed to replace all mentioned. good luck.
Bud AKA THE Guru
@@THECompressorGuru yes, i mean crank pin bushing sir ( it made from machine steel with harden steel or not ? )
And for the bearing, if i use ball bearing not roller bearing its ok or not ?
@@fachrudine I do not know the hardness of the crank pin bushing. as for the roller bearing I used the wrong word they are ball bearing units.
@@fachrudine thinking about it it is probably not that hard because the rods are the only aluminum. it is only the rods that move on the bearing the bearing does NOT move on the crank
Oil coming out of the head of my air compressor
that is never good. lots of questions what compressor? how old is it? have you done any recent work? you can contact me through thecompressorguru.com email me everything know and I will try to help.
Bud
how many liters of oil do you use ir 2545?
its less than 3, usually 2 and a half. I just looked at the spec sheet and its not on the IR spec sheet for the 2545/
. thanks Bud
rebuilding my saylor beall 705 ,is there any method for checking clearance for oil in the rod bearing. Just installed new bearings and I feel a little movement between the bearing and crankshaft. Simply put is there a acceptable tolerance or should I have the crankshaft out and miced?
I am sure there is a clearance spec. I do not have it off the top f my head. nut you can also use a plastic gauge kit. you put a piece of plastic between the insert and the crank torque the bolts and measure the plastic . a chart will then tell you what clearance you have . you can contact Saylor Beal and ask for the clearance and then you will know where you are at . you can buy a plastic gauge kit at most advance auto stores.
Thanks, I appreciate your help and I enjoy your videos very much.
I need spears for my Air high compressor
how many hp ingersoll rand compressor sir?
I am confused by the question How many Ingersoll rand compressors what? HP stands for High pressure that is the second stage of a 2 stage compressor.
My compressor volume is 1.2m³/min
Hello
howdy
/..