Must Know Info For The China IDF Clone
Vložit
- čas přidán 6. 09. 2020
- Hello
High Quality IDF Bearings from Amazon Link:
www.amazon.com/gp/product/B07...
Take off vacuum Ports for the IDF Link:
classiccarbs.co.uk/product/we...
Fuel Float is setting 4.25mm but 4mm to 4.50mm should work but if you want play with it, go for it! Find what setting works for your combo. - Auta a dopravní prostředky
Switched to Dellortos years ago and have never looked back.
You shouldn’t measure float open/close height with weight on the seat and valve.😊
thanks for the information all the way from 🇵🇭
Good info. 👍
Thanks, Hey I could hear the differance as soon as you hit the gas. My engine was T 1 2080 cc 40 mm intake. It was a 2176 44 webers. So say I detuned it, hoping to get better 8 miles a gallon lol. It's in a 70 Bus. Thats my reason for getting these 40 clones. I had no idea what vents/jets they would show up with. To give an Idea on these chinese jets, Idels are stamed 50. one gauges as 50, one as 52.5 or a sloppy 50. The other two are over 60. I checked my weber jets same type of thing. I buy some 55 weber jets same deal none check out the same. I bought more 55's from CB. These are a hair smaller so thats a +++. Also getting 32 vents from CB. So far I am happy with the weber clones, you have to dail them in, just as you do with real webers. Right now / yesterday I'm putting a diffrent oil pump and need to install it's axles. I'm in oregon and it's snowing ashes/smoke. If the house and shop burn down maybe I can save the Bus. It does have a very comfy bed in it .
Those carbs would go well with your 2276 motor. If you are going to change the cam also port the heads. Good vid.
Hi, enjoying your videos and well happy with the info thamx, I'm currently doing a project on a 3.5V6 their 287hp and around 250ftlbs tourqe as standard and I want to run 3x48idf, but it's confusing trying to work out what jets, emulsions, venturies, air jets etc I need to get her going, what do you recommend please for this setup?. Once it's done I will get it tuned properly. Its such hard these days as my tuner has now retired, he always setup my builds for me and I've done some unusual builds over the years, always liked webers and my v6's but I'm at a bit of a loss.
Many Thanx Gaf
I just got a 44 from Lets Buy Throttlebody-Store on Aliexpress and it had bearings with plastic seals just like the ones you bought and they said "Japan" on them...
Thanks I also want to get Chinese 44 idf
How can I check the vaccum on Kadrons, is there a way you can do it? Can you do it at the balancing tube outlet?
Good info.
So you would say these carbs are worth the effort? Im thinking of buying some from maxpeedingrods for a triple setup on a v6.
Do you have any instructions on how to prevent flooding?
Question since you have done a lot of work on these clones. I have one carb that reads differently with the sync gauge.
Is there a way to adjust that? The other carb is perfect between the barrels. If no adjustment is possible I just I’m pulling carb.and readjusting butterflies . Also you are so correct on needing to go thru these carbs and check everything. Check Jets sizes with a measuring tool, do not believe what is stamped on them. Check accelerator pump jets also. Check butterfly’s and replace throttle shaft bearings. Thanks again for all the work you have done and posting it for us. 👍👍
You can adjust the air bleed screw to adjust each hole. Next to the mixture screws with the 8mm nut locking in down
Cómo ajustar el acceleration pump? Puedes hacer un video para esos clono? Thanks
I like my clones also i have 40s however i tried the cb performance 40 upgrade but the venturis where too narrow could my 40s actually be 44? I kept with the stock working fine but do you know if there is a difference in venturis?
Did you use 607 2RS or 609 2RS ball bearings?
How did you install the AFR gauge?
No matter what I do, I cannot get out of the 10.5-11.5 A/F zone at idle on my clones. The last and final thing I've done is lower the float down like you did here, no difference. Either idle jet dimples are machined properly or possible needle and seat weak like you shown here.
Bought a set of Chinese IDA48s, thanks for the info! Any links to the eBay bearings? Think I want to replace them too, was concerned the sloppy nature was due to oversized casting/cavity.
It's actually from Amazon.
The link is down below the vid
Hola motor.. disculpa un IDF 44 crees q le sirva a un motor 1641.. 😬 tendría q cambiar los Venturis a 28 o 32 o es mucho ese carburador para el motor.. porque compre un flags 44 tipo Weber.. y estoy en ponerlo y no?? Me podrás ayudar.. saludos desde Tijuana 🤟
You measure upside down?? Shouldn't it be holding the unit side on then measure
You can do it both ways just be careful when measuring upsidedown
Can i better buy a weber original needle valve and float pieces and install them on my fajs clone to have better float level?
So these carburetors don't have a cold start system at all?
Is that Fajs branded?
Damn...my chinese idf was calibrated to weber specs and it ran horrible..that's why i put the solex back on
Check your float
Will there be the same adjustments on a single IDF setup the float
Would love to know this anwser?
I bought 40's and bearings. can the bearings be removed , without removing the shaft ? What about the butterfly screws ? Do those come loose nice or are they pinned over ? are the 40 vents really 44 vents ?
If the bearings were not locktited at the factory they should just slide out using a very strong magnet.. I have a video that shows me how to remove the bearings. if you want to see that you just have to go back in time to find it but it's labeled so you should be able to find a video.
To answer your other question. you do not have to remove the throttle plate or the shaft unless they used Loctite on the bearings then you going to have to remove them be very careful when you beat the crap out of it to remove them don't damage your shaft or you're going to have to order one from the UK.
Hi
Why not setup float like real Weber? Should float level be like real Webber’s? That you shows in a video
Do you know where I can get the auxillary venturi for the clones. Mine melted
CP performance is your best bet
where did you get your jet drills. I'm not finding any this small
They make drills so small you can barley see them. Try drilling a .025 hole in amco brass
I checked how much a big bore kit cost for your Porsche motor and they are TO MUCH. I dont know if they were Biral Cyl. The ones with chrome sleeve
I know..... it's crazy how expensive everything for the type 4 engine is!😬
There all junk everytime I would get them running perfect something else would need adjusted. Broke down bought a set of webers put them on haven't even a backfire yet its been 2 years.