Video není dostupné.
Omlouváme se.
Charging a copper lap
Komentáře • 20
Další v pořadí
Automatické přehrávání
How to Charge your Copper LapElie Ghanime
zhlédnutí 4,1K
Charging a Copper LapEg Jewels
zhlédnutí 29K
Resurfacing a Copper lap with a Saw BladeJustin K Prim
zhlédnutí 10K
UDĚLAL Z 20KČ 1200KČ!Štěps
zhlédnutí 127K
ОБЯЗАТЕЛЬНО СОВЕРШАЙТЕ ДОБРО!❤❤❤Chapitosiki
zhlédnutí 18M
A teacher captured the cutest moment at the nursery #shortsFabiosa Stories
zhlédnutí 55M
REAKCE: Tiskovka Clash of the Stars 9 je extrém!FattyPillowTV
zhlédnutí 113K
How to Prep a Copper Lap for PolishingJustin K Prim
zhlédnutí 3,1K
Cutting my own gemstone design in Blue TopazMatt's Corner of Gem Cutting
zhlédnutí 114K
Dopping a gemstone with Super Glue - Faceting Lesson 4Austin Moore
zhlédnutí 10K
How to charge Metal Polishing Laps with Diamond 💎 Easy and Fast Tutorial 💎 Copper Zinc Tin BATT LapGermanGemcutter
zhlédnutí 10K
Batt Lap: Polishing GemstonesMoreGems.com
zhlédnutí 60K
Dressing my copper polishing lapBob Lakey
zhlédnutí 2,5K
Kevin's Faceting Tech Note -- 07/25/2015 --using Batt Lapelegant obsessions
zhlédnutí 16K
Buried Treasure: Deep Cleaning a Used Polishing LapJustin K Prim
zhlédnutí 9K
Preparing Metal Laps for Gem Cuttingultratecusa
zhlédnutí 46K
ДЕДУШКИН РАССОЛ В СОЛО⚡️КАН АНДРЕЙ⚡️
zhlédnutí 14M
Jak rozebírat tyhle skleněné mlýnky na sůl, pepř a další koření? 🤔Vojta Dalekorej #WRTECH
zhlédnutí 312K
Attack a Terezka jdou na rande… KINOAttackShorts
zhlédnutí 335K
Proč si Fotbalisti STŘÍHAJÍ Díry do Kopaček?Horis PLUS
zhlédnutí 135K
Best Toilet Gadgets and #Hacks you must try!!💩💩Poly Holy Yow
zhlédnutí 22M
REAKCE: Tiskovka Clash of the Stars 9 je extrém!FattyPillowTV
zhlédnutí 113K
Barča má nervyDodo Hraje
zhlédnutí 129K
Tohle už je vážně moc...Vidrail
zhlédnutí 188K
anyone stumbling on this video, his demonstration is wrong. This gentleman's video is a much better tutorial: czcams.com/video/OPGkLtgLCrs/video.html
Burnishing should be done before the diamond is added. The whole point of burnishing is to work harden the copper surface so the diamond does not embed itself all the way into the soft copper. The diamond need to be stuck in the copper but sticking out enough to cut your work without leaving copper streaks in that work.
Thank you!
you can also use an agate burnisher, (much cheaper than a Norbide stick) which is fine, because it is still quite a bit harder than copper and will still burnish the copper..
Thanks for going into the details as you did.
Question: I noticed you changed the speed a few times. Being a spinning circle the actual speed is low towards the center and increases towards the edge I would think you could use a higher rpm when your pressing in the central zone then lower your rpm's as you work towards the edge. I guess the question is just how much speed matters, maybe not that much? If a faceting machine were like a belt sander then it would all be the same.
Hola desde Argentina muy buen video no te entiendo pero me gusta
thanks...how to use copper lap for bre-polishing and fainal polishing? and which polish powder use for best ?
.how to use copper lap for bre-polishing and fainal polishing? and which polish powder use for best
what is the type of disk ...thank you
What is the advantage of using copper lap instead of any other kind?
sir what is the type of disk ...thank you
When you use the lap for polishing, do you lubricate with water? Oil?
He said olive oil but you can use varsol or turpentine as well
sorry to finish using a copper dist or what?
Do you use this bearing for other grit diamond, or do you dedicated just for 5his grit?
Better to separate the grit are still harder then thenbearing so it could in theory embed onto the lap as well as the bearing but make sure your lap should be softer then the mateeial thay you are gonna lap and the charging tool should be harder then the lap plate or as hard or even harder them the lapping compound
Can I use the bearing to charge another lap with 3000 or do I need to use a new bearing?
To be safe use different bearing or wash and brush the bearing with metal brush
Is your fingerprint present till this day?
I am a newbie.
sir plz my halp for GOD
how to r p m ti moter