Hangar 9 Carbon Cub 15cc FINAL BUILD Part 5
Vložit
- čas přidán 6. 09. 2024
- It is FINALLY done!! We think it came out great and hope everyone likes it as much as we do!! Can't wait to fly this thing! Maiden time... ohhhhh yeahhhh...
Hangar 9 Carbon Cub 15cc - bit.ly/HHCarbo...
Dubro 6" wheels - amzn.to/3wmHqH7
ebay.us/JJr37D
XOAR 16x10 - amzn.to/3o5KNOS
ebay.us/ivo6lJ
Power 60 Motor - amzn.to/2ZW5VPT
ebay.us/sfIo7x
Castle Talon 90 Amp ESC - amzn.to/304g0tN
Rhino 6s 5000mAh - bit.ly/HKrhino...
Power HD Servo - ebay.us/axYEAr
*VIDEO GEAR WE USE*
GoPro HERO 7 Black - amzn.to/3wjCP8x
Neewer On-Camera Video Mic - amzn.to/3kaRj5N
*THANK YOU FOR SUPPORTING OUR CHANNEL!!*
When you purchase through our affiliate links from Amazon and other sites, we may earn a small commission at no additional cost to you. This allows us to provide more valuable content to you, our awesome audience!
If you would like to donate and help us with our ever-increasing glue supply 😜 - paypal.me/ungl...
You can also find us randomly lurking on Instagram -
/ ungluedmodeler
#ungluedmodeler #rcbuild #carboncub15cc
I have this plane, And ready to maiden mine as soon as the weather is good, I am using a SK3 5055 430Kv motor, Turnigy Plush-32 100Amp ESC, And I don't have any 6 cell Lipos, So I am using 2 Zippy 2650's 40C connected in parallel, A 15x8 APC prop, And 6in. Kaven tires. My build techniques are quite different then yours, But whatever works is great!, A little tip for those trying to install decals is i don't use Windex, I use a spray bottle with warm water and a drop or two of Dawn dish soap. ( I clean all areas for decal with Isopropyl alcohol first), Spray the area, apply your decal, The soap lets you slide and position the decal, When you get where you want it, Use a paper towel at a corner to hold it and squeegee the water out ( I use a old credit card), use another paper towel to just touch and dry any wet areas, let dry overnite, do not touch, Done! I know decals can be frustrating, going from good to bad in seconds, so I hope this helps someone.
What a journey this was! Incredible job! You and Mary make it easy to follow. It would be so much harder without your detailed instruction. And the tips and tricks you’ve learned and then pass on to your viewers is fantastic! A big thumbs up to you and Mary. Can’t wait for the maiden voyage; it will be wonderful to watch. Thank you for your tutoring!
Glad you enjoyed it!! Quite the build it was haha. The maiden went perfect BTW. It’s coming soon!!
I have my little Carbon Cub S2 and I love it but this one seems to be the real deal!
That S2 is a great little plane! And yes this Hangar 9 Carbon Cub is legit!! Excellent ARF to upgrade to in the future!! We love it
fingers crossed for the maiden. enjoy.
Looking good, that’s a nice big airplane! I’d call that an assembly though, not a build. 🙂
Thanks for taking the time to video your assembly progress!
Thanks!!! And yea I agree assembly haha 😂 thanks for watching!!
Nice! Have a safe maiden!
Thank you very much!
WOW looks great guys. Good job. Great building and beautiful photography, thanks for sharing. Happy Flying.
Thank you so much. Means a lot to us! Can’t wait to fly it!
Oh man!! Ur gonna LOVE IT!! Carful when doing steep bank turns don’t pull to hard on the elevator she will tip stall on ya if ur not fast on the rudder. Other then that they fly so good
Thanks for the tip! I’ll be thinking of that on the maiden!
@@UngluedModeler good luck on the maiden!! Can’t wait to see it flying. Loved the build a video!
Don’t know if I sent u this but here’s some clips of mine flying czcams.com/video/v1YBF-PycAo/video.html
What attention to detail! Very good build. Looking forward to watching your maiden flight.
Thanks!! Came out great. We did the maiden and it went just fine!! Coming soon haha
sweet job am at that point on mine to I went with gas and smoke so inside going to be way dif but its sweet plane
Nicccce! That’s gonna be awesome!! Smoke will be so cool on this!!
I can't wait to see a flight video ;)
Just did the maiden today!! Vid coming soon!! Spoiler....went amazing!! LOL 😂
2 things... 1, lose the center prop bolt and nylon washer! The torque can easily kill both parts of that setup! The knurling of the prop hub needs to contact the spinner backplate, which has to contact the prop, to prevent spinning on the shaft. At best it only slips. At worst it can be dangerous by loosening and slinging a prop under power.
2 Hint: get a connector to patch the lights to one cell of the lipo balance lead. Each light can have its own two pin connection to any random two balance wires. That’s 3.7-4.2 volts and I understand these lights work on a single cell lipo. The amp draw is minimal and will never be noticed.
Thanks for tips! Yeah I am watching my prop setup closely. We did the taxi test, multiple full power pulls, and did the maiden the other day two full battery packs doing high speed passes and it did great. Didn’t budge one bit. We’re going to keep an eye on it. Thanks for the tip with the lights we don’t mind our setup. We have a mini switch inline it’s not bad to plug it all in while your down there doing the wing connectors.
you can use a 30-40 ohm resistor per LED and feed the lamps from the receiver voltage.
Mary @ 11:58, LOL! I made the same sound. Came out fine though. If you press the plastic down with a piece of plywood or a book it'll come out nice and smooth, not that it matters on the inside. I like the black spinner, goes well with the overall look. One sharp-looking plane.
The wind hasn't been cooperating lately, has it? Friday looks good, but I'm on shift so I'm going tomorrow. If I see you out there, don't worry, I'll stay away if I see you filming!
Thanks! Yeah my fingers were crossed for that window heating LOL. And yeah holy cow the winds lately! Got up to 48 knots last two days!! 😳
@@UngluedModeler The wind gods heard you mention a maiden flight and decided to act up. Happens to me every time. Looking forward to the vid, the scenery will make it even better. Probably make some folks jealous that we have the world's best natural flying field.
Glad to hear the maiden went well, looking forward to the video. Want to see how you managed to squeeze that thing into such a small spot!
Haha thanks! We had to go Friday. Vid should be up soon!
Great series, thanks
You're very welcome! Glad you enjoy them!
nice work! well done my friend ! what a beautiful carbon cub ! really like all the videos parts !🎥🎬✈💙Michel Raymond from Québec 🌎
Thanks!! Means a lot to us she really did come out great! Maiden went great too check it out!!
I also like your workshop really nice ! and your wife does a very good job with the cam !✈✈✈💙
I went with the three servo harness and a transmitter activated switch
Time for a trailer won't need to disassemble it.
Omg I know! Lol. Funny you say that cause we’re wanting to buy one!! We have another even bigger plane coming!! We haven’t shown it yet!!! 😮😮😬😬😬
@@UngluedModeler Nice!
Bravo! Well done how-to video all around!!! I just purchased the H9 Cub and planning on a installing a gasser 20cc DLE . Do you have any plans to modify your Cub with a gas engine and do a How-to set up? I H9 should pay you to be the official "instructional video " for all their planes! Good Flying!!
Thanks!! Wow that’s a HUGE compliment thank you very much! For now we have no plans of converting over to gas for the Carbon Cub. But I have tossed around the idea of doing a gas setup in another H9 plane in the future! Oh and the DLE 20cc for the Carbon Cub is going to be perfect! Very popular engine for this plane. 🙏😀
@@UngluedModeler Well I will say everything regarding putting the Cub together, landing gear, wind shields wiring etc. were so detailed and really will save me so much time in my upcoming build! Tell Mary her camera work is really good for hand held!!
@@aidengriffen Thank you again we are so glad you and other viewers found these videos to be helpful!! It means alot to us really thanks again! And Mary reads these comments also she is grateful for the kind words!! 🙏
Building this plane now! I I installed a 20 cc Stinger gas engine on mine. Finished gluing all the horns on yesterday after I sprayed them with grey primer to match the color scheme. Great video's. I just finished an Extreme Flight 91" NG blue and white with a 76 cc Great Power engine. Do you fly any 3D planes? Also have you seen the new 100" bush plane by Extreme flight? It takes a 35 cc motor. I plan to buy it but need a new transmitter to operate it. Thanks for these videos, helps answer quick questions when needed!!
Thanks! Sounds awesome with that 20cc stinger!! Should fly amazing. Your Extreme with that 76cc sounds badass! And no I have not seen Extremes bush plane I’ll check it out!! I LOVE 3D planes but just haven’t done any up but I do like them. I’m always drawn to bush planes for some reason hahah
Great series on the build. Can I use a 3 cell aa pack with 4.5 volts for a brighter LED lights? My kit did nut come with a dry cell holder for the LED.
You absolutely could but even Ali said at a higher voltage the lights will have a reduced life span. They are rated for 3Volts I believe.
I bought this kit and the wrinkles and the mistakes made from the factory were terrible. All over the airplane the covering was cut short. Then tiny patches were coming off and sticking to my iron when I was ironing the covering. My kit was wrinkled 50% more than the one in the video. Attention to detail like pulling the covering tight on angles didn't happen. That caused the leading edge to not be stuck down at the wing tips. It's so loose the heat gun didn't help. It has sanding dust under the bottom of the wing covering. On the top of my wing there is pieces of balsa that is visible that they ironed over under the covering. The covering job was not sealed at all on the seams. When you try to get the seams sealed the other side will pull away because it was not stuck down. The flaps and ailerons were cut short on the ends, then patched over. Trying to get them to seal did not happen. I stripped the covering off of the ailerons and flaps and started over. My son does a better job covering and he is a kid. The wing not block sanded and bottom of the wing is uneven. The elevator has a big sander mark in two places. It is very visible. My kit must have been built on Friday LOL. Dear Horizon please sell this kit without covering. It would have been faster to cover it myself than try to fix this mess.
Wow!!! That’s crazy!! Very sorry to hear that. Sounds like you have it taken care of already but Horizon actually has wonderful customer service I bet they would have sent you a completely new plane. Pain in the butt I know to pack it all up but I’m sure they would have helped you get a new plane. Lots of times they even have you keep the old parts.
Looks realy good! Please, no Bigfoot landings with this one ;)
About the lights, would it be possible to connect them to the receiver instead of the battery tray? The voltage shouldn't differ that much?
Thanks!!! Hahaha yeah this one will land soooo much nicer than the Bigfoot lol. As far as the lights on the receiver I'm sure it would work but for how long? Typically the BEC puts out 5-6 volts. The lights are 3 volts sooooo.
@@UngluedModeler True, better safe then sorry.
I love this whole build you guys did! I went and bought myself one as well. But my question is where did you get the quick connection for the wing wires. And what is that called? Hope to hear from you soon!
Thanks
Hey sorry just saw this comment!! Thanks!! It’s a very cool plane. We got the connectors at Valley View RC. Great people to deal with check them out. They are just called wing harnesses I believe or something like that. Good luck!
I purchased a bigfoot and set it all up and elevator and throttle operate at the same time.. Any input?
Couple of questions. What radio system are you using? Did you set up a new model when you set the bigfoot up? It sounds like you may have an inadvertent mix going on between the throttle and elevator channels.
@@UngluedModeler I'm new to the rc plane scene. So I purchased some starter stuff to make sure it is something I will enjoy as much as my other rc products. The transmitter and receiver are flysky fs16x. Everything on the plane works as it should just not the throttle and elevator. I watched a few different videos on setting up the transmitter and it binds correctly but still the same issue. Wasn't sure if there is a way to set up what each stick does. The weird thing is that the elevator works normal going down on the stick but when I go up on the stick the elevator moves but the throttle revs with it
I was thinking the receiver might be bad out of the box
Yeah that is very strange. Are use open TX on my Taranis but what happens when I set up a new model is it asks you what you want each channel to do. If I was you I would try setting up a brand new model from scratch and then triple checking that you have assigned each servo correctly to the appropriate channel. And somewhere in your menus you have An area for mixes. I would check to see that you do not have an elevator to throttle mix also. That is where I would start.
@@UngluedModeler ok. I'll give it a try but where it says mixes it say off. The transmitter has a display mode and it shows the channels working correctly. Thats what made me think the receiver was bad. Been pulling my hair out lol. Also you and Mary make it look so fun. That's what made me wanna try the bigfoot
טקסט מקור
נהנתי מאוד לראות את הסרטונים שלך ועכשיו התפנתי להתחיל לבנות
ועוד יותר נהנתי מהמקום שאתה נמצא בו נראה שכייף להטיס ככה,
אצלי בישראל אין הרבה מקומות להטיס ,מאיפה אתם?
165 / 5000
תוצאות התרגום
I really enjoyed watching your videos and now I am free to start building
And even more I enjoyed the place you are in. It seems fun to fly like that,
I do not have many places to fly in Israel, where are you from?
Will there be a Part 6 video of a first flight?
Yes! And thank you!! We do have the maiden video of it!! We didn’t call it Part 6 though. Just Carbon Cub maiden!!
What size screw did you use for the windshield? Really enjoyed your video!
Thanks!! I can’t remember the size off hand but they were pretty small. No where local had them. I checked Home Depot, Tru value, cal ranch, tractor supply. No one has screws that small. I ended up finding them at a specialty fasteners store in Las Vegas. Kind of like a local McMaster Carr type place. I want to say they were #2’s for some reason but can’t remember exactly
@@UngluedModeler Thank you, I figured they were #2 or #4.
Are you using any gyro on the plane? I ordered a Hobbyeagle Super 4 just for the sake of using technology...
No I'm not using any gyros. Plane flies fantastic its very gentle. I use 30%expo, dual rates and I also turned down my elevator rates a tad bit more to smooth out some pitchy tendencies.
Not trying to be a jerk but why is the covering so wrinkled?
I still think the flaps aren’t scale.
Не качественная обтяжка. Морщины.
I hope that the coating doesn't come from Hangar 9 that way...that's not good quality control and poor craftsmanship.
Nice plane, boring motor
Thanks! Wanted electric for this one. Plenty of power. Clean and easy. Doing an XCub with a DLE 61cc right now also.
@@UngluedModeler electric isnt my cup of tea but nice we all can choose these days 👍
Yessir that’s right! Great to have options. Electric is great to get to the field and fly right away clean and massive torque instantly. Can’t replace the sound of a gas engine though that’s for sure!
@@UngluedModeler exactly my thoughts 👍 nice model and resisting buy now.. A saito 82 would be just fine and might have one just layin around 😉