This video is very helpful. Could you PLEASE help me out with a few questions I have about this single bank fueling setup? First of all: does this setup still let both of the oxygen sensor readiness tests pass, as in read "Complete"? Could you check this with your setup in MHD? Second: with the DR700 kit from DOC Race, both oxygen sensor bungs are at the end of the downpipe, post cat. Can both bank 1 sensors be mounted there for this setup? Because you mention bank 1 must be installed post-turbo/pre-cat and post-cat.
No, not sure about the readiness test tbh. You typically want bank 1 precat in the manifold and post cat downstream in the downpipe. I have not ran it any other way. Sorry I couldn’t help more
@@ReignRegime Thanks for your reply. My car is FBO now and with a DP fix installed I pass all readiness tests. Do you think I'd still be able to pass them with this single bank setup and going ST?
im running a GFB III controller that is connected to Mac solenoid, if i disconnect it i lose all GFB functions for duty, gain & overboost protection. could i just do 02 sensor relocation and only select "single bank fueling" and reflash? Do we have to do pin relocation and rewiring of mac solenoid to dme? im also tuned thru Wedge, custom e85 ST KIT. thanks in advance. @@ReignRegime
@@ReignRegime does the upstream stay in the manifold and the down stream in the hood exit?? How did you make the down stream o2 to reach the hood exit since the connector is in the bottom of the car??
Bank 1 post cat gets confusing but the O2 sensors both have heat wrap. One is grey and one is black. The one wrapped in black is Bank 1. I’m using wedge tuning
Hi, i am currently running ST with mac solenoid(JB4 + BEF), my question is : do i need to change pin location in DME or just need to activate the single bank fueling in MHD and reflash? , Thanks in advance
@@ReignRegimeI have the reflex plus too and get smoke when banging gears aux 1 from the reflex is connects to my boost solenoid still getting mixture codes 1 and two maybe my tuner sucks or me but I followed instructions I deleted bank 2 primary and secondary because that’s what it says to do, also on dr700 kit pi full E
Cd919 had a video too ,but this video also shows alot 💯 am doing mine too all bank 1 doc vu tune .next u should show if it be able to pass inspection
Intro🔥
This video is very helpful. Could you PLEASE help me out with a few questions I have about this single bank fueling setup? First of all: does this setup still let both of the oxygen sensor readiness tests pass, as in read "Complete"? Could you check this with your setup in MHD? Second: with the DR700 kit from DOC Race, both oxygen sensor bungs are at the end of the downpipe, post cat. Can both bank 1 sensors be mounted there for this setup? Because you mention bank 1 must be installed post-turbo/pre-cat and post-cat.
No, not sure about the readiness test tbh. You typically want bank 1 precat in the manifold and post cat downstream in the downpipe. I have not ran it any other way. Sorry I couldn’t help more
@@ReignRegime Thanks for your reply. My car is FBO now and with a DP fix installed I pass all readiness tests. Do you think I'd still be able to pass them with this single bank setup and going ST?
@@trenbolonie when u say "FBO", that means your still on OEM twins?
You have to tune it differnt or single bank fueling
The pins are same for a mac solenoid installed pin 7 repin to pin 25
Yes 👍🏽
So I already did this for a Mac solenoid …… am I supposed to do it again or I can just run the 02s now
Are you running only DME? No JB4 or any other external boost controller?
Just DME. I have a GFB Boost controller but it’s only to read boost. It’s not wired to control anything
Great vid, so if your MAC soleinoid is connected to the DME, what purpose does the GFB serve? Just a boost gauge? Thank you in advance.
Just boost gauge.
im running a GFB III controller that is connected to Mac solenoid, if i disconnect it i lose all GFB functions for duty, gain & overboost protection. could i just do 02 sensor relocation and only select "single bank fueling" and reflash? Do we have to do pin relocation and rewiring of mac solenoid to dme?
im also tuned thru Wedge, custom e85 ST KIT. thanks in advance. @@ReignRegime
Do the two lower o2’s both have to be disconnected or do we keep those connected as well.
Only bank 1 connected. So pre cat and post cat are both connected
@@ReignRegime does the upstream stay in the manifold and the down stream in the hood exit?? How did you make the down stream o2 to reach the hood exit since the connector is in the bottom of the car??
Being that you have a custom tune did your tuner have to adjust the fuel table or anything after doing this?
Not sure exactly what the tuner did but he did have to make adjustments for this
Which plug is for bank 1 for the post cat O2 sensors and also who is your tuner?
Bank 1 post cat gets confusing but the O2 sensors both have heat wrap. One is grey and one is black. The one wrapped in black is Bank 1. I’m using wedge tuning
Hi, i am currently running ST with mac solenoid(JB4 + BEF), my question is : do i need to change pin location in DME or just need to activate the single bank fueling in MHD and reflash? , Thanks in advance
Gotta move the pins homie
I just did this not getting any volts to those connectors
Is there any different steps if I am using ReFlex+? Also have my MAC solenoid wired to ReFlex I believe
Yes for reflex, pin 7 goes to Aux 1
@@ReignRegimewhat is aux 1 im having same problem. Is that the second wire slot in the white connector?
How did you wire you Mac? My Mac goes to the boost control you that you have the 02 going to
And what would I do if I have reflex?
@@TheBakeryBoysI don’t have reflex so I’m not sure. My Mac solenoid is plugged into the first port for boost solenoid.
@@ReignRegimeI have the reflex plus too and get smoke when banging gears aux 1 from the reflex is connects to my boost solenoid still getting mixture codes 1 and two maybe my tuner sucks or me but I followed instructions I deleted bank 2 primary and secondary because that’s what it says to do, also on dr700 kit pi full E
can you get emissions done with single bank?
Not sure, don’t have emissions where I live. I’m also catless so I’m positive that I wouldn’t pass anyway
Bro are you on instagram can you help me with this