OK, your video was extremely helpful. I'd like to add that disconnecting the harness gray connector on top of the transmission before usncrewing part, makes jobe a lot easier, because valve body slips out. The harness is a screw on and adding a little wd40 and gently tapping with screwdriver removes it real easy. also access to the oil dipstck is a lot easier is f you connect funnel thrught the removed tire panel. reason to remove this part appears on scanner as a selenod either in open or closed position and basically car not fuctioning because transmission will not do its job. Potential savings... thousands of bucks, Mechanich ill tell you that you need a new tranny and will probably just replace assemby. Good luck to all.
I also have Nissan 1.6 CVT J10 Qashqai scanner tells me Solenoid 1 Not showing a reading & car will not drive forwards but it will reverse. I will order a valve body or can the solenoid be replaced??
Definitely over-refilled. Shouldn't have taken more than 4.5qt with proper procedure. Like the video though. It's the first fix that I'd seen for the 16-19 sentra. Id seen for 2014 but was searching for a 2019 model. Thanks.
Greetings...... I just change the Valve body and didnt work, the transmission work totally out of the normal functionality..... do I have to re-progaming in the computer?
I got a p0746 code 2013 Nissan Sentra what can I do to fix it ? I put new solenoids in valve body no change ? Could my metal belt be faulty????thanks for a reply
1. The transmission is gone. All the hairy stuff is metal shaving sticking to the the magnet. The gears are tore up. 2. CVT transmission do not use ATF fuild they use CVT. No way it fixed
Very informative and helpful.
Great video sir and well done .
Thank you.👍🏅🏅🏅🏅🏅
OK, your video was extremely helpful. I'd like to add that disconnecting the harness gray connector on top of the transmission before usncrewing part, makes jobe a lot easier, because valve body slips out. The harness is a screw on and adding a little wd40 and gently tapping with screwdriver removes it real easy. also access to the oil dipstck is a lot easier is f you connect funnel thrught the removed tire panel. reason to remove this part appears on scanner as a selenod either in open or closed position and basically car not fuctioning because transmission will not do its job. Potential savings... thousands of bucks, Mechanich ill tell you that you need a new tranny and will probably just replace assemby. Good luck to all.
I also have Nissan 1.6 CVT J10 Qashqai scanner tells me Solenoid 1 Not showing a reading &
car will not drive forwards but it will reverse.
I will order a valve body or can the solenoid be replaced??
Did this fix yes you can just clean solenoids
Safety first ❤️
Thank you for this ...
You are welcome
What symptoms did you have prior to changing the valve body? Also, how did you unplug the valve body wiring plug from transmission?
Did this fix your problem also what check engine codes did you get? Thanks for the video!
Hello, I am doing the same thing to a 2015 Nissan Versa. How did you get the old plug out? The black part that goes up into the transmission
Hello were did you get the diagram of valve body on this car???
Definitely over-refilled. Shouldn't have taken more than 4.5qt with proper procedure. Like the video though. It's the first fix that I'd seen for the 16-19 sentra. Id seen for 2014 but was searching for a 2019 model. Thanks.
How did you remove the plack plug for the connector?
What about the transmission fluid low code
i have the same car, and i have high 3RPM at 120Km is it normal ?
Did you have to do to perform any computer programming for the new valve body?
No CVT programming just clear all the code when you finish the installation ...
Greetings...... I just change the Valve body and didnt work, the transmission work totally out of the normal functionality..... do I have to re-progaming in the computer?
But did it fix the problem? & what was the problem?
How much did you pay and where did you get your Control Body Valve?
Did changing the valve body correct the problem? Is it running good?
yes
The most important question was not answered in the video. Did it fix the problem? And what exactly was your problem to begin with?
Sorry for the long wait but to answer yes also service with a new trans fluid please twice
I have a P0967 code on my 2015 nissan sentra. I'm not even sure if this video helps me.
That code also indicates a malfunctioning valve body. Did you try this repair for your car?
I got a p0746 code 2013 Nissan Sentra what can I do to fix it ? I put new solenoids in valve body no change ? Could my metal belt be faulty????thanks for a reply
Did you get your issue fixed? If so what did you do? Thanks.
Same issue here
Did it work?
What happened after that? Have you resolved the problem?
reset the code and go for a test drive ...
Ratio control valve had spring on it!
You don't have to perform any programming just use a professional scanner to erase the code
How do you remove plug that’s the main thing smh 🤦🏾♂️
remove the round plugs first and two on the middle also after unplug the wire connection on the side where to filter located ...
Hi, i have a nissan sentra with cvt problems, is the car you replaced the valve body on still running?
Yes still running
Where did you bought the new one?
Nissan dealership I believe for $339.00
@@blackston22 i need one for nissan x-trail . i'm in Saudi Arabia . how can i order one valve body
@@blackston22 did you call them or go into the dealership?
There is a lot of fluid in the the torque converter
Did anybody notice he put regular automatic transmission fluid in a CVT transmission? I think he’s gonna have problems in the future.
It said CVT on the oil he used. He's good...
Regular fluid is red
1. The transmission is gone. All the hairy stuff is metal shaving sticking to the the magnet. The gears are tore up.
2. CVT transmission do not use ATF fuild they use CVT.
No way it fixed