Install Altaros regulator to Diana Stormrider
Vložit
- čas přidán 8. 09. 2024
- Installation of Altaros airgun regulator for Diana Stormrider.
For more information about us, our work and products visit www.altaros.cz
CZcams Audio Library :
Echinoderm Regeneration by Jingle Punks from CZcams Audio
Library goo.gl/YmnOAx Pentagram by Audionautix (audionautix.com)
Well upgraded complete, testing tomorrow.
Can't wait to put one in my Diana Stormrider Gen I and maybe later put one in my Diana Stormrider Gen II
I think the fill tube/gauge off a diana bandit will work in the stormrider . Then you will have a fill pressure gauge too .
Tested it today. Oh my god !!!!!!! say no more.
How manny shots do you get out of 1 fill?
Great video !!!
Does anyone know the exact outside diameter of the moderator/suppressor on the end of the barrel?
Very good, congratulations, like and +1 subscribe!
I just installed it in my Stormrider and set the regulator to 125 bar - but the gauge on my rifle shows only around 80-90 bar. What may be wrong? 😬
It must be said that I pumped the rifle to 200 bar via an external gauge 😉
please write to our email regulator@altaros.cz for more information. Above all, the age of the regulator or whether it was purchased ( directly from us or from a distributor ). You can currently try setting the output pressure to 150bar on the scale
Was the port replaced for one with a larger diameter hole for more air ?
If so, the port on the air tube & the barrel need to be larger as well.
The airgun on video was limited to 16J and required a larger transfer port for proper operation with regulator. Replacement always depends on the specific model of the rifle.
How many short with regulator?
. 22cal
you can find this information here: www.altaros.cz/en/diana/77-6052-diana-stormrider-airgun-regulator.html
great video. but the firing pin lever is not original. where can i find it?
Would this work with the diana bandit/ Artemis PP800. It seems to be exactly the same gun. Just different branding. Thank you!
Serve no cilindro de alumínio flashpup wood?
How do I know how much to fill the airr ifle now when my gauge does not work anymore? What happens if the pump's gauge doesnt show correct pressure?
it is necessary to use an external manometer or purchase a plug with a quick fill and a manometer.
If the gauge on the pump shows poorly, it is the same as if the gauge on the airtube shows poorly. Here comes the safe safe dimensioning of the airtube at higher than operating pressures .
hiya, i was wondering if thi
s would make any difference in the uk version of the gun that is limited to 12 foot pounds.
the same regulator can be used for different outputs including 12ftlbs.
You indicate that a new transfer port comes with the regulator - when did that start? I ordered one and installed one in a Diana Stormrider that I have yet to shoot across a chronograph. Have a air pressure level indicated on the rifle that makes me believe the setting that I adjusted to is too low despite several adjustments to increase the setting / adjustment.
If the regulator was not purchased directly from our website, but was supplied by Diana (they have their own instructions), then the packaging may differ and in this case it is necessary to contact them directly. This transfer prot is especially suitable for European countries where there is limited performance. The outlet pressure can be increased with a side screw. If the purchase was on our e-shop, then contact us at one of our e-mails . Thank you
Do you make regulators for the Sam Yang Dragon Claw models of airguns perhaps?
We have several of this regulator, please write to email altaros@altaros.cz
How much regulator?? Price?
Do you have shipping to the US?
yes we send to the US
i turned the screw too much. how can i reset the regulator setting....i didnt think its possible to turn this thing in way too much... -.-
I been using these regulators now since August 2019 - had it down to ~60-65bar according to the pressure gauge in front of the regulator. The regulator kept this setting till last weekend.
I first noticed a shift of impact by about 1Mil up on the field and the loud report, then checked the system pressure and it must crept up to 100-110bar. Now I'm wondering what went south on the reg without taking everything apart a million times. Is their a video that shows how the do this particular Altaros regs?
if dirt got into the system, then the pressure may have risen and the outlet pressure adjusting screw may have been pushed off.
If you make a longer flat-blade screwdriver, it is possible to readjust the outlet pressure without removing the regulator. If not, just unscrew the front plug and pull out the regulator. Unlike all other regulator models on the market for this rifle, this one is the fastest installed and removed. For more information, just write an email.
@@AirgunRegulator Thanks for the quick reply. I hope that adjusting the set screw will do the trick. Otherwise I will try the procedure from your service video. Till last weekend the reg was working outstanding.
Does the Transfer Port you include with the Regulator increase muzzle velocity (FPS) ?
Would drilling the existing one do the same thing, for someone not buying your regulator ?
And what is this "outlet pressure can be increased with a side screw" ? Does this increase FPS also ?
Thanks for any help, I'm new to PCP airguns... I just bought a StormRider .22cal, but it's only 495 FPS... I want 800-900.
hello,
Increasing the transfer port will help to increase the flow to the barrel and thus increase power. can you tell me where the information with the side screw is written?
But the valve transfer port Is it included in the purchase?
what size was installed in the video?
I have the diana stormrider 7,5j... what size should the transfer port be?
when purchasing a regulator in our e-shop, a transfer port with a 3mm holle is also included.
you can make the hole to 4mm ,i have with 1,65 gramm diabolo round 38 joule. 245-250 ms, with 0,85 gramm 270 ms,10 min work in selfmade,
@@AirgunRegulatorfrom were i purchase regolator for pr900w.
@@amirrasheed9616 www.altaros.cz/regulators/90-2881-spa-artemis-pr900w.html#/25-caliber-177_45mm/40-required_energy_with_regulator-75j_55_ft_lbs
how many shot increased ? and FPS ?
Where we can buy the regulator?
www.altaros.cz/cs/Diana/77-6052-diana-stormrider-regulator-tlaku.html#/62-awpdetails-
Hi my friend I want to know altaros air pressure gauge thread measurements
it depends on which device it should be for, please write to the email on our website (it doesn't matter which one)
@@AirgunRegulator I have kral arms sniper
@@AirgunRegulator czcams.com/video/bVw0xKmRdJA/video.html
would this work with the smk pr900w ? i believe the rifle is exactly the same with the only difference being the power is 11.8 ftlb just under the legal limit for the united kingdom
119/5000
We have no experience with this particular model, but according to your appearance you should be right and the regulator can by install in this model.
@@AirgunRegulator thank you, I actually ordered one from your website and I selected my manufacturer power output and my required output after the regulator is installed which is both 12 foot pounds
How is that the regulator breathing?
This regulator does not need to breathe.
Why do I need to replace the o ring?
it depends on many things. It is generally around 2-6 years. The service life of the seal extends to store the rifle at a low pressure of 100-120bar
Is it enough to replace only the transferport to get more joule?
it always depends on more parameters. For some rifles, just increase the transfer port its enough for more J.
@@AirgunRegulator I have a Diana Stormrider
@@ibow177amg3 Type of rifle was intended to mean that there are a number of Diana stormrider models on the market, with different settings being supplied to each market (state). So this cannot be said, for some rifles yes for some no.
@@AirgunRegulator Oh okay i understand now, thank you for your help
Mám Artemis PR900W, je to skoro to samé jako Diana Stormrider. V ráži 4,5 mm. Naměřil jsem u ní úsťovou rychlost kolem 235 m/s při tlaku 200 bar a 175 m/s při 100 barech. To je rozdíl 60 m/s! Pokud bych použil váš regulátor a nechal na něm nastavený výstupní tlak 100 bar, tak bez výměny transferportu by byla úsťová rychlost kolem těch 175 m/s, jestli jsem to správně pochopil. A tlakoměr na zbrani by ukazoval stále regulovaný tlak 100 bar, dokud by tlak v kartuši neklesl pod tuto hodnotu, je to tak? Nevíte náhodou jaké úsťové rychlosti a energie střely ráže 4,5 by se s touto vzduchovkou dalo dosáhnout při použití tuningového transferportu a tuningové pružiny při nastavení regulátoru na 100 barů?
Přímo na dílně jsme 4.5mm tuto verzi neměli, ale osobně si myslím, že by také bylo vhodné vyměnit transferport za větší a nastavit například výstupní tlak 110-120bar. Menší tlak nedoporučujeme , jelikož je zde zbytečně silná pružina úderníku a mohlo by docházet k velké spotřebě vzuduchu na jeden výstřel. Jak jsem již psal, pušku jsme na dílně neměli, takže ani orientační hodnoty nedokážu přesně říci, ale myslím si že by se puška měla dostat na 16J.
Does that little air port come with the regulator?!?
Yes transfer port should be standard shipped with regulator.
Diana stor.rider instal artemis