BMW INPA NCS Expert WinKFP Tool32 Windows 10 Install
Vložit
- čas přidán 6. 09. 2019
- How to Install BMW Tools including INPA, NCS Exper, WinKFP, Tool32 and more using BimmerGeeks Standard Tools & K+D CAN Cable on a Windows 10 Laptop. Installation Instructions:
1. Login to your laptop using an Administrator account
2. Open a browser, search for "bimmergeeks download" on google and click the first link, then click "standard tools".
3. Download the BG Standard tools 7zip file, then download 7zip 64 bit and unzip the files.
4. Right click "St212.exe", select "Properties", then click the "Compatability" tab and select "Run in compatibility mode" under the section box below make sure it says for Windows 7 and click ok.
5. Run "st212.exe" Using all default settings except the 4 checkbox options in the "select additional task" window regarding "backup and restore" and "create desktop/quick launch icons" .
6. After install completes, select "No, I will restart later" to restarting PC.
7. Navigate to your C:\ drive and delete the folders labeled "EC-APPS, EDIABAS & NCSEXPER"
8. Replace those folders with the "EC-APPS, EDIABAS & NCSEXPER" from this download by copying them to the C:\ drive.
9. Copy the 3 files inside the OCX folder and paste them in the C:\Windows\Syswow64 folder.
10. Open Command Prompt as administrator & enter the following commands exactly as written below:
cd c:\windows\syswow64
(Press Enter)
regsvr32 mscomctl.ocx
(Press Enter & wait for "Registration Succeeded" message)
regsvr32 msflxgrd.ocx
(Press Enter & wait for "Registration Succeeded" message)
regsvr32 comdlg32.ocx
(Press Enter & wait for "Registration Succeeded" message)
11. Place the "BMW Tools" folder(BMW icon) on your desktop. Shortcuts to all the software are inside.
12. Make sure your cable is set to COM-1 with a Latency Timer as 1 in device manager.
13. Reboot Computer.
14. Login again and open BMW Tools and you are ready to start using the programs.
For educational purposes only, perform at your own risk. If you are not sure what you are doing you should consult an ASE Certified BMW Technician. Copyright CycleVIN L.L.C. 2019. - Auta a dopravní prostředky
Massive props to you for making this! First timer with INPA, diagnosing a misfire/injector issue that only happens when vehicle is warm. Just replaced all ignition coils with Eldor so I know it's not that. Car starts normally too. Only starts hesitating when warm and under load. So this is a major help!
Thank you! Your instruction was the best from any other videos online. Successfully installed and ready to use for my car.
Thanks for doing this. Love your straight forward common sense explaining and ditto with your responses to comments/questions
No problem, enjoy!
110% the best friggin video for this, everybody else that I've tried to follow was so discombobulated that I couldn't get anything to work.
Step by step instructions were super clear, I got it working in like 15 minutes where the past two nights I couldn't get the bloody thing to work.
You sir are the man. I can't thank you enough for this tutorial.
No problem, have fun playing around with your vehicle
Holy cow, great vid, thank you!
I can't believe how many unhelpful turds on the forums say this stuff is "straight forward" to install and get all rude when people ask installation questions. It is doable, obviously, but downloading from a somewhat obscure site, installing in root of C: drive, deleting and copying directories, changing com ports, and doing anything in an admin command shell, is pretty much the opposite of :straight forward." Thanks again, can't wait to get my cable and spend a little time with my new e46.
No problem, enjoy playing with your car!
You are the best! Was about to get rid of my Dcan cable after 3 failed attempts. Thanks 😊
Whoever you are you are the man. Easy straight fwd and articulate. Thanks bruh I was able to install this on windows xp pro. The only change was the cmd for .ocx in xp. Thanks I would buy u a beer.
Thanks we just used the software to monitor transmission temperature when doing a fluid drain and refill recently, saved us thousands hopefully the same for you as well.
Thanks its works for me i testet more downloads and totorials the only from you worked.
I have coding my new injektors at my 335 n54.
greetings from Germany.
Your tutorial was perfect and on point. Thank you!
No problem, enjoy playing around with your car.
Hey do I have to be logged in as a administrator account?
Thanks, your guidance is still relevant…and very helpful!
Thank you so much :) finally an instruction that works on win10
No problem, enjoy!
thank you so flippin' much holy guac there is no fuzzing way, you are the goat
You're welcome enjoy!
Thanks man that worked perfectly for me 👌
No problem!
Got it working , thanks so much awesome tutorial
No problem enjoy we just used it to code some new injectors the other day, saved us thousands.
That worked perfectly!!! Thanks!!
Anytime sista! Enjoy messing around with your car =)
Did you get it in English
Big like 💪thank YOU🙏🏻
Great help, huge thanks for all the info
Thank you very much for making this video in a way that simple & easy to understand. I have a 2007 BMW 328i & I’m trying to work on it myself after my 2016 VW Passat was totaled. However , after I let it sit for abt 6 months, with no battery power, the steering column locked up & I was told to get the cable, software & use my laptop to unlock it just to get the engine to turnover. (Push to start).
If you have any important advice besides o not brick my Bimmer, I’d appreciate it! Again thanks for the video, you’re awesome!!!
Great video! Thanks a lot.
Thanks & No problem
Thank you so much for this. You're the best!!!
Great instructions, thank you for posting it, bless
No problem, God bless you too!
Thanks for the help!!!!
Thank you! 👍
Excellent. You rock.
hopefully you're still on here. i installed this on my windows 10 laptop. install went flawlessly, but the problem i'm having now is that inpa will detect the cable, but says ignition is off even if the ignition is on or if the car is turned on.
Excellent video thank you very much
No problem, enjoy working on your car.
Hokey CRAP! No one ever said anything in the whole set up when I've tried it the &898 thousand time before about running it in Windows 7 compatibility mode. Which makes sense because why would anyone make a version that actually just loads into the world largest windows version?? LOL. Anyway thank you very much for this video!
Thank you for the guide! Where did you buy your K+DCAN Cable? I want to get a compatible/functioning item
No problem, we got our cable from BimmerGeeks.
Thank you !
No problem enjoy maintaining your car without paying the stealership a fortune.
it workssss.... thank youuuuu
No problem, just used it to bleed the brakes and flush the coolant. Enjoy!
many many thanks bro
No problem any time brother
Hello I installed everything as instructed but for some reason I can’t edit the settings in the INPA cable any hints? It hasn’t installed the driver on my computer but my computer is fully up to date
EXCELLENT. {NOTHING MORE NEEDS TO BE SAID ABOUT THIS VIDEO but the BimmerGeek version does have issues with E53 X5 and libraries may be damaged. I have not had time to verify this statement. Will update when I have a solution or proof.)
Thanks alot you are a freaking life saver dude. successfully reset my ews and got the car to fire after almost 3 months of being down
No problem glad to hear you got your car up and running without having to spend a fortune at the stealership
New to this. All I want to do is cycle the ABS pump to do a complete brake fluid flush. I think I can basically bleed the brakes then do again while cycling the ABS pump. I have an e92 M3. Will this software work for that?
Nice tutorial thank you, I just retrofitted the Sport Automatic Transmission in my 2008 E60, how can I use this software to code the ECU?
You might need ISTA-P for programming the ecu, or the BimmerGeeks protool may be able to.
Hi, CycleVIN do you recommend a lap top dedicated to the BMW Tools (INPA, NCS Exper, WinKFP, Tool32 ) or can they be added to a laptop that's used for other purposes/programs.
That's up to you, we actually use ours on an old laptop that we use for other stuff as well.
I've used this once to code injectors MSD80/1, tried it again and all im seeing is idle speeds under injector flow. Maybe disconnect the battery?
Here is a video that walks you through how to code injectors on an msd80/1 ecu: czcams.com/video/Zb4CdXq-8RE/video.html
thank you !
ur the best of the best....
Thank you.... you are the man on this shit!!!
hello, ask for clarification about the d-can. cable pin 7 and 8 must be connected for bmw 10/2007 and 92?
If you have a K+D CAN cable the switch should be to the right for your car.
Install went great, double checked my steps and for some reason getting "Error opening error log file---->Abort !" when I try to launch INPA after restart??
Not sure try contacting BimmerGeeks and see what they say
Installed using this video. Getting the DSC module for my bmw E90 in German, is it anyway to get in English?
if i instal the program and dont have cable yet, can i reboot computer or i have to wait to install cable and then reboot computer ? thank you
I got to the end when your supposed to drag the bmw tool icon to the desk to but mine still says bmw tools as a folder not an icon.
Same u ever figure it out?
@@jackson95tattoos yea I did, I ended up going back into the file I unzipped and rereading the introduction PDFs and I missed something. The instruction PDFs are the key read them all and follow them.
thanks man , wich obd2 cable is the best to order for connect my bmw e46 2000
BimmerGeeks K+D CAN Cable
thanks for the great video!
I've run into an issue though. my INPA seems to be in German?! Is there a way to switch to English? Installation and set up went like a charm, and the software does connect to the car, but i can't really do much since i cant tell what the options are. trying to bleed the brakes on my e90.
This free version is in German. Use Google translate otherwise you can always pay for the BimmerGeeks ProTool.
My FRM module was repaired by a tech guy, probably he does not paired with CAS and my car now does not start, how would i know if there is issue in the FRM module?
What about if using an ethernet obd not usb ? Still do device manager part ?
Please help me :
Run INPA and :
ApiInit: Error #135
API-0015: HOST COMMUNICATION ERROR
API initialization error
No API call possible!
Hi, nice video,
I am new to these tools and I am trying coding a bmw x3 2006 with a new battery different ah capacity.
Do these tools work better under windows 7 32 or 64 bit version?, so I can set up my computer the right way.
Thanks, and great job, and you got a new subscriber :).
Coding the new battery is very difficult with these tools, it is much easier to do it with the new BimmerGeeks Protool app.
For using INPA can i connect the computer to the car via OBDII (Bluetooth), I don't have have the cable (and hard to get it delivered at this time (COVID 19 , and living in Iraq).
No you need a K+D CAN cable to connect your laptop to the car as far as I know. Some of the newer phone apps can use a Wi-Fi dongle.
thanks for the video. Question, after install it connects to my vehicle but everything is in German??? I think. any advise on how to solve?
I followed your instructions and it worked as you described, one issue I am having is that I can not change the INPA.INI file in any way. Any changes are ignored and I need the R56 menu. Have you run across this issue?
We have not encountered this issue
Nothing seemed to happen when I plugged in my cable but it does come up as a USB device and I did change it to COM1. It should work then no? Also the push switch: which position is K and which is D?
Switch to the left for older models and in between or to the right for newer ones.
Any ideas how to set this up for ADS? I got old XP laptop with serial port and need scan my E36 (pre obd)
No clue, if it's that old it may not be compatible.
Thank u sir
THX!
No problem enjoy!
When downloading the file it says failed system busy after attempting to “scanning” any thoughts?
NCREXPER MISSING expert mode profile for coding? do you know how to add or where to find profile for it?
Not sure but you can always use expert mode in the BimmerGeeks ProTool App
This should work as well with mini cooper r56, but when you open INPA it's not on the list. What I should do?
You need the F series IPO files. Check out this thread: www.bimmerfest.com/threads/inpa-on-f-series.698506/
Everything works perfectly but winkKFP does not and I need it to change vin on my DME and advise?
You might need to buy the protool and default code the DME. Put a message out on the bimmergeeks Facebook forum and see what ppl say.
i keep getting IFH-0010 error datatransmission to controll disturbed. i keep looking stuff up and solving this but nothing works, also ,error#95 sys0005 object file not found
Just wanted to confirm this is usable with the E60 and E9x chassis? I remember hearing they had a change of CAN somewhere in the 2000s.
It works on our E82 platform just fine, E6x and E9x models are listed in the main menu so you should be fine as long as you have the switch on your K+D CAN cable in the correct position.
e6x and e9x until 2006 2007
@@albaner0090 I think you are incorrect since E9x started in 06-07...
I followed your video and installed the software smoothly. However, when my cable was plugged in at USB port, it was not shown in the Device Manager as "Port & COM". Instead, it showed "Other Devices" for which I cannot change port settings. Any comments on that? I work with Windows 10 pro. Thank you.
It may be due to your use of the Pro version of Windows. We used the regular version. Contact BimmerGeeks and see if they have any other drivers you can try.
yo same issue did you get it fixed?
Hello friend, I do everything step by step and finish up to step number 10. But the bmw icon does not appear. and I can't place it on the desktop.
I'm doing it with your video on one computer and the whole setup on another laptop. I have gone step by step, I even copied the instructions or commands from your text file with the instructions, I verified each of the letters or characters and I can't get the BMW icon where the extracted files are.
What I can do ????
Hi. Are the error messages displayed in English or German? Program language is English, but on some versions the error messages are in German.
Downloaded the bimmergeeks standard tools, where is the ST file? I can’t find it anywhere
After downloading you have to unzip the files with 7zip.
I am having an issue with inpa recognizing my M54 engine. It suggests the M56 but then it is in German. Any suggestions? Great video BTW.
You probably have a M56 DME, what year make and model is the vehicle?
Hello sir, does inpa do CAS alignment?
Yes check out this video: czcams.com/video/dSFvmDYvz4Y/video.html
do you know how to fix the error 704 "Assembly identification number not found in the files determined by xxkfconf.da2"
Not sure, maybe try doing it again...
Is it enable to support E87 N43 engine?
Hey dude! Awesome video. I want to say thabks first. I have a doubt though, Im trying to code the led tail lights from prelci to lci, and the video im following says i need to load this Revtor's ncs expert profile, or expert man if needed. how can i get those, or how can i add them to ncs expert profile list.
czcams.com/video/uPmP1uQUX9U/video.html this is the link for the video FYI , min 16:35
@@Nico3dd it's much easier to do with the BimmerGeeks Protool.
@@cyclevin159 how can I use it? I'm new at this 😁😁
@@Nico3dd it's an app you can download it in the Google Play Store
How do you get the st212 you skipped past the part where you unzip and where did those files come from mine only says bimmergeeks standard tool and won’t let me open it
If you Can't figure out how to unzip the files you probably shouldn't be using this...
hi How to code AUX in bmw e63 (645cica modele 2004) by NCS Expert
I found a lot of tutorials but the methods are different
I can't get to know the ideal methods for coding (what is the difference between expert man profiles, revtor's ...)plz i need tuto
thank you so much
Marwen Hadhom I need it to!
@@DB-px5gj
here is a download link but i'm not sure about program reliability
I haven't tested it yet
www.bimmergeeks.net
Check out this video for NCS Expert Coding: czcams.com/video/Zf-7KVp3oU0/video.html
when i go to type in the commands in the command prompt, it tells me 'regsvr32' is not recognized as an internal or external command. Any idea what this is?
Not sure make sure you followed all the previous instructions exactly, if it is still giving you an error contact BimmerGeeks.
right click on the command prompt and you will see where it says Run as Admin...then you should be good to go
There is no st212 in my download. Just BMW tools, ec-apps, ediabas, ncsexper. What do I do now?
Contact BimmerGeeks and let them know. They can send it to you directly.
Thanx mate, i tried it with windows 8.1 64 bit but always get the ERROR 126 Api initialization error
Can someone help?
Do i have to connect the cable with the car to get Inpa running?
This tutorial is for Windows 10, for Windows 8 you may need to contact BimmerGeeks and see what the install procedure is.
Once you get to command prompt how do you enter the command with c:\users\administrators? Because I can't get rid of that command. Thanks
right click on command prompt and open it up as an administator
Hey man, when it comes to the Command Prompt section. I try to type in the following commands but an error message opens up “the module was loaded but the call to DIIRegisterServer Failed with error code 0x8002801c.”
Can someone help me?
What version of Windows are you using?
I get the same, i use windows 10
Run the cmd as administration
Hey i followed everything but when i want to open Inpa it sais api32.dll missing... on win 10 64bit how do i fix?
Try uninstalling and reinstalling again.
when i copied in CMD i got error that it was loaded but also it was failed with some error code
Hi its working perfect but there are only one problem .When I read the errors the results pops up in a other language how can I fix it ?It only happens when I read the codes .The rest of the app are in English
You can use the MHD App to scan and clear codes in English for free through your tablet or phone. All you need is an OTG cable to connect to your K+D CAN Cable.
Followed everything to the letter, but when trying to use INPA I get the #135
API-0015 HOST COMMUNICATION ERROR
API Initialization error
No API calls possible
Try contacting bimmergeeks and see if they can offer some insight.
I followed all these steps but it gives me error when I attempt to run job on inpa or tools32, "ecu service not supported" is the error on tools32 for frm short circuit counter job. I had a kDcan cable from Amazon and returned it and got one from bimmergeeks because I thought that was issue but still same error.Any ideas what it can be?
Not sure, try contacting BimmerGeeks and let us know If you figure out why.
@@cyclevin159 issue might be because I don't believe standard tools comes with sp-datens files?
Thanks for this tutorial. I found a problem ... when i open INPA, press INFO, EDIABAS is not recognized Ini Path ????? Ecu path ???? Interface ?????. Do you know what can i do to solve this ?
Are you using a BimmerGeeks cable or an amazon/eBay one?
@@cyclevin159 amazon one. But i think this has nothing to do with the cable. Cable works and i tested with protrool.
If i open INPA - cable is detected
Congratulations on the video, but is it possible to install it with the same procedure on windows 8.1?
Not sure, give it a try and let us know.
@@cyclevin159 possible on 64 bit
@@gorskynuvo9715 Yes this is for 64 bit versions of Windows.
Could someone clarify where to open the command prompt, so do I have to copy those 3 files there? if so, how do i get them connected to it?
Click on the Windows icon in the bottom left corner of the screen and type in "command prompt" in the search box. Then follow the instructions in the video.
@@cyclevin159 It’s hard for me to interpret English from a video because it’s so bad for me.
But then, I do get the command open but after that I no longer understand or can interpret what needs to be done. So did you copy those three pieces of data straight there, or did you write?
I keep getting virus treatment from windows defender every time I try to install with st212?!?!
We use BitDefender so Windows Defender is turned off, BitDefender scanned the files and found no issues...
thanks for tutorial i have it install now. but am yet to have a cable can i do that later?. can i close the command prompt windows?
We waited until we got the cable, but you should be able to. Let us know if it works.
@@cyclevin159 hi it works fine, after installing the software first. It took some days before I received the carble. I now understand the diagnostic area but the coding and programming is my problem.
After installing everything as in the tutorial, I connect it with the car, shows me that the cable is detected and ignition on. After entering the model n46 and the engine appears to me error Versions do not match. Possible malfunction!
Press ok then I see the error Language variants do not match. Possible malfunction!
Can someone help me?
Thanks!
It says that for us too, just click ok and it should let you continue on to use the software.
@@cyclevin159 Thanks mate!
should do a icom video with ISTA-D and ISTA-p
You have to crawl before you walk...we actually use TIS when necessary for the occasional job that INPA isn't able to handle.
so I have downloaded the correct version of 7 zip as well as the bimmergeeks file but cannot figure out what do do from there, the 7 zip file becomes 7z1902-x64.exe and the bimmergeeks keeps the same name and is 140,718 kb in size, when I right click the bimmergeeks file I do not have an option to unzip it
nevermind, now I got the option but before I was not... weird
@@joelgurnsey2570 no worries glad you were able to figure it out.
@@cyclevin159 now my issue is that I do not get a st212 file and when I right click the bimmergeek standard tools and go to 7 zip and click extract here nothing happens and the files dont show up in my c drive or anything
I'm Having same issue
Will this work for e92 n55?
I’m using a K+DCAN cable and it doesn’t show on ports from device manager, it shows on ‘Other devices’ that’s the only problem I’m having because it’s not showing that my cable is on nor ignition on INPA. Help? :(
Does it allow you to access vehicle information?
I was able to fix it! I had to go to device manager and update the cable using WiFi and it changed from other devices to Ports. In case anyone has this problem update your cable using WiFi!
CycleVIN thanks for the quick reply though! Very much appreciate it brother !
thanks!!! pin 7 and 8 must be connected whith bridge??
If you have an older car the switch should be to the left, if newer to the right on your K+D CAN cable.
@@cyclevin159 my car is 10/2007 bmw e92 coupe
@@giorgiovitali4591 The switch should be to the right for your car.
@@cyclevin159 THANKS!!!
for some reason everything works but inpa, ncs expert, and wink kfp did i do something wrong? i get the messege " the code execution proceed becuse api32.dll was not found." what do i need to do to fix this?
Try reinstalling and see if the issue persists.
@@cyclevin159 it works now thank you!
hello can i have the inpa software download link for windows 7 How much does it cost