How to Install a Gas Block Perfectly Straight Every Time
Vložit
- čas přidán 11. 05. 2023
- If you're tired of struggling to install a gas block and ending up with crooked results, then this video is for you. In this walkthrough, we'll show you the foolproof method we use to ensure a perfectly straight gas block installation every time. Whether you're a seasoned builder or just starting out, this tip will make your life easier and your rifle more reliable.
I use a piece of angel hair spaghetti to line up the block and port. Stick a piece in your gas port and break it off flush. Slide gas port on, look look down the barrel, and rotate. When you get to sweet spot where the piece of spaghetti will slide in and out of gas port you're lined up perfectly. Tighten your set screws and use a cleaning rod to break the spaghetti.
Angel Hair PASTA...actually Capellini....Spaghetti is another size of pasta. I'm gonna try it!
I used thin spaghetti. It fit perfectly.
This video is a good example of why I like Ballistic Advantage. No hype, no bull. Just straightforward and functional performance.
Love these videos. They have helped me get through multiple builds using BA barrels. Keep up the great work.
Great video but it would be helpful if you guys would dimple all barrels for the average builder.
Great timing! I am getting ready to do this very thing to my BA Handson Premium .223 Wylde 14.5” barrel, with the awesome pinned gas block, that I just bought from you guys. Thanks for the info and the amazing barrel. I love to support local (Florida) companies and I can’t wait until it’s done.
Excellent breakdown of the install. I love the explanation of the why and how. Thank you.
Love your straight forward no bullshit way of explaining things! Fantastic! Love your videos! Thank you!!
Videos like this make me feel good about the BA components I bought to build a BA AR15 14.5
I bought one of BA's hanson profile uppers in 16 inch, and I love it. Accurate, simple, built with intention and checked all the boxes in my regards, for a great price too!
Thank you for this instructional video. I'm building my very first Ballistic Advantage AR15 Carbine. This really helps me tremendously even though I've built a couple of Aeroprecision USA AR15's previously.
I run your 13.9 Hanson midlength barrel and I love it. It has performed flawlessly. 🤘🏼
I think many over think this install. Common sense alignment and correct tightness of screws and you're good. I build several ARs month and never had one issue. I do use 243 loctite on screws.
BA is the way! Great info and timing. Getting ready to install your low pro on a DMR build.
Instead of setting up the camera at 10 feet away where we can see your face and glorious beard, maybe set it up at 6-8” from the gas block so we can see wtf you’re doing. Or maybe set up a second camera.
😂👏👏
🎯
More beard than gas block in this video
I could see perfectly fine dork
Be careful with a second camera
As long as you know hole spacing: SLR Rifleworks Dimple Jig, will work better than others as some shoulders are closer and you won't be able to use KAW Valley Dimple Jig, but Kaw has an ease of measuring hole spacing and comparing to your actual gas block.
If you have Aero Precision adjustable gas block, it is 0.500 inches.
Others may be different. Ballistic Advantage gas block I had on Hanson barrel was 0.500" as well.
Thank you, great tips! So grateful for the Hanson barrel with the pinned lopro
Luv BA Barrels! extremely happy with my LR 308 build using a Hanson Profile premium lopro. Had some trials at first getting it to cycle. had to open up the barrel gas port a couple thousands, but it cycles flawlessly now and unreal accuracy with a 18" barrel. Word of advice - USE BA's BOLT. THE BARREL AND BOLT WILL MATE PERFECTLY and you wont be cussing yourself for blowing your hard earned money on a generic bolt - ask me how i know. Looking to build my next one now:)
Brother I love all the videos really missed y’all keep up the great work both in videos and barrel making I have 2 and love them both
Most gas ports are drilled .295" off the shoulder, some gas blocks have a .265" spacing so there could be .030 between the shoulder and block and pushing it up to the shoulder could block part of the port. Also if whoever drills the gas port will spin the barrel in an indexer and drill a dimple in the bottom it makes it a lot easier on the home builder.
And brownells did a video showing a spacer is not needed. They did this with a bore scope the gas port hole in the gas block is much larger than the hole in the barrel.
I have a Hanson barrel with a slightly canted gas block. I inserted a bore scoop in the barrel to see up the gas port. I then inserted a fiber optic cord all the way inside the gas tube and illuminated it to see up inside the gas block. I was able to see a clean perfect circle. No gas port obstruction whatsoever. I have 1200 rounds through the rifle with zero issues. Runs like a champ.
Try this trick to straighten the gas block tho. Clearly you’re qualified. I do like the justification and even if you’ve done all of this high level “QC” I think you can get that block straight. You’re a superior mammal and champion! Thank you for being you!
@@clinthanson8005 honestly I don’t feel like disassembling the upper again. Everything is thread-locked. Even my Midwest industry mlok rail around the barrel nut. I have the irons dialed in nicely. I think I’ll leave it be. As long as the port is not obstructed im good. You can barely tell that the gas block is canted. You’ll have to really look for it. I appreciate the kind words brother.
@@tajituck888 my hanson 625 barrel is slightly crooked and against the shoulder. It has a very small gas port of 0730 and wont lock open with 223. I used a kak dimple jig and it brought it away from the shoulder 30 thousands and perfectly up and down. I'm really sad i cant use the pin anymore as it's not aligned now that i dimpled. The dimple jig mechanically centered the gas block over the port
@rmblwgn same here.
we want to see the next video, adding the gas tube... this is a cool series for everyone to learn... I know YT doesn't like these kinds of videos, but we appreciate them
I just finished my 10.5 in 300 blkout build, the barrel is ballistic advantage, and boy oh boy, is she a straight, one of the best barrels I've ever shot out of. Just as accurate as my BCM 14.5. My only gripe, I didn't get a sticker with my purchase of it. Looking forward to building the 16 inch ballistic advantage in the coming weeks.
Yea I had to purchase by BA stickers but they do give patches
Woof... 16 inch blackout is a b to tune with the pistol length gas tube if you're using a hux and subs... Probably gonna have to drill it out a few wire sizes. I'm thinking .08 to .085 maybe.
I'm not even building a gun right now I just saw your video. Bro, you speak my language. I hope you do more tutorials for people, imma be looking your way
Good info. I'm working on an AR Pistol in 8.6 Blackout/.308 for a few months now. Have the tools, just need an area with a vice and room to do it.
Thanks boss. VERY informative!
Great knowledge! Thank you👍🏼
Thank you. I actually learned something watching yt today.
When I started building my own ARs, I bought an inexpensive gas block, drilled all the way through the block using the rear screw hole as a guide, then sharpened the rear of the drill bit so that I can use the bit to line up the gas block, snug up the front set screw and mount the barrel in my drill press vice.
A couple light touches with the bit in the press starts the dimple just enough and it's dead straight, every time.
Great video.
Oh thank god for the video I’m about to do my first one I’m so glad I went with BA parts
So excited to put together my BA AR I’m proud I went with BA
THIS is why we do business with Clint and BA.
Great vid!
it would be nice to see close ups of everything you are working with
Very Nice, thank you
I just did my 308 with a longer Faxon barrel then upgrade my Rugger 556 with an adjustable block too. The hole in the gas block is bigger than the barrel hole. I used the spaghetti method. Works brilliantly.
Great vid. Thanks for the info
Great information
Great video!
Damn fine explaining. Thanks.
Thanks for the tips !! I would love to see the jig you use to drill the roll pin.
Wish I saw this a week ago just put my first AR together and used a BA barrel, but I did struggle to get that gas block straight.
Never had an issue with alignment. I always eyeballed the hole to make it’s in like with the picantiny on the receiver, then eyeballed inside the gas block and lastly eyeballed the gas block alignment. All my guns gas perfectly after said alignment style
Great Build Tips. Would like to know which fixtures you are using to secure the upper to the vice.
Thank You!
Your company makes the best barrels in the industry.
Great barrels, another phenomenally accurate barrel make is Criterion!
No no they don’t
awesome. thanks.
Really like the gun smithing videos
locktite wont do anything because the barrel gets hot and thats how u defeat loctite but rockset is very hard to get out so i think just tightening them up is enough because u already have it pinned.great video as always.
I would have so paid more to have you pin the blem gas block i just got. But Im gonna give it a shot. Looking forward to using your barrel soon
great content and tips and hints. I do have a question about the gas tub though. After everything is all aligned pinned, and tightened, should the gas tube be a tight fit, or should it have just a little bit of free play? The reason I ask is, because I have heard that if the gas tube is tight fit, with no amount of free play, that it could essentially effect the accuracy of your barrel during barrel whip. In short causing it not to be, a true free floated barrel.
Bought Rosco in the past, really wanting a BA barrel for my next build
Anything wrong with the Rosco?
On my first build and kinda screwed up the process. I pinned the tube to the lowpro before mounting the block to the barrel. I had this aversion to tweeking the tube for the install. It was a BA Hanson barrel. While I was fairly sure I got the ports aligned after pinning the block, it still bugged me. So here's my tip. I got a little plastic tube, the same size hospitals use to run O2 through your mask. Turns out, with a drop of CLP in the end of it, it will slip right over the gas tube in the upper. Bingo! I verified full blow through, no different than when I blew through the tube before installing. Not bugged anymore.
...I used an old fashioned ruler and pencil to line up the gas holes and the fish tank airhose trick to make sure the holes are aligned...
Great info. I have always been curious as to why when the gas port is drilled in the block, it isn't drilled all the way through the the block? As this would allow indexing of the block using a pin gauge or other means during installation, eliminating the need for the coil pin. It also should not leak as the gas tube itself would obstruct the orifice. It seems like this would eliminate alignment issues potentially without adding any additional steps to the manufacturing process?
I’ve drilled mine out before and zero issues
Where have you been, dude? I (we) hope you find time to continue with the videos, again!
I got a clamp on type that uses 2 screws to clamp it and it great.
i had the screw into the barrel type lock up making me have to cut it off to get the set screw out!
Great vid
i have an MP sport 2 with delta ring drop in handguard and love it. really want to swap out the fsb for a low profile (and probably adjustable) gas block. will that be enough to retain the handguard cap, or should i just free float it in order to change the gas block?
I miss Sarah
What ever happened to her? She was a little ball of energy!
RIP
@@theREALdingusMD Seriously? 😟
Outstanding, I also blow air through mine to make sure the hole is lined up and clear.
Personally I use thick spaghetti to verify.
Does it matter much if the dimple for the gas block screw sets the block away from the shoulder just a little? I just installed an adjustable gas block on an 11.5 that I couldn't get the carrier to slow down enough with spring and weight alone...
Right on, appreciate the insider insights! Keep em coming. Love your barrels & the lowers that I own. I will add, the cat that mentioned a bit closer camera shot would be helpful is indeed on to something. Perhals with a bit more BA swag in thd background too. Keep that glorious facial fur in the shots too though! 😉🤘🇺🇸#ARJunkie #2ARights #RepealNFA
Thanks
I have several of these Hanson barrels, and why? because all gas blocks need to be pinned. BA offers a number of barrels with pinned gas blocks and FSBs. It's the one operation that you can't do at home without a high risk of failure and having a mess on your hands, especially with the hardened surfaces that barrels have now. Great value.
Agreed on the value of pining. Can't believe how many rifles i see put together on youtube with only dimpling and loctite 😮
This video does little to dispel my belief that there is some key bit of info that I'm not seeing that 😮insures gas port/ block alignment.
Just bought a Hanson barrel and chose the Superlative Arms Adjustable block instead of the pinned lopro. Wish you would have had the option to have the dimples drilled on the barrel.
My BA 16" 5.56 hanson is short stroking like an sob. Not, the buffer, spring, gas obstruction, bcg or any of its components so I hope this helps. Why go through the trouble of drilling the barrel for a pin if it can still be canted? Just dimple it.
I don't have the setup to pin mine, but I do have a dumpling jig. Is it normal to just have 1 dimple as opposed to 2?
Outstanding
Chris - what vise block are you using to assemble that upper? My flimsy Brownells upper vise clamp isn't cutting it
Get a SLR gas block dimple jig, dimple the set screw under the gas block. Install gas block and tighten set screw..
Insert the coil pin and verify the gas ports are lined up with a cheap bore scope..
Remove set screw and apply Rocksett on both set screws and install set screws..Done..
Eyeing the gas block is a perfect way to clock the gas block, do it right with a simple dimple jig from SLR..
Fixing botched gas blocks is job security for AR gunsmiths lol..
Newb first-time builder here, the BA barrel I bought with the block already installed, do i need to do this? Fully acknowledge this is likely a stupid question. Thanks BA!
Or you can line it up using the rear set screw hole then take a pencil and draw a T-shaped index mark on the barrel. The will show you how far to push it in into the journal and where to line up the gas tube.
Not sure how the video would show you to install the gas tube when you've got the block in place first.
Another way that's not quite as precise but still works is to plug the chamber and muzzle then slide the block/tube assembly on. Use a can of compressed air and short squirts to give where the block is lined up with the port- you'll be able to tell by the sound. One the air is flowing, tighten the set screws.
I have built over a dozen ARs, and I always install the gas tube to the gas block before installing it on the gun, using a jig to drive in the pin. I guess he is going to thread the tube from the inside of the upper then out into the gas block?
I do the same compressor trick. Saves time and effort.
Not responding to QC issues and not backing up your accuracy guarantee is why I don’t use BA anymore.
@BallisticAdvantage
Do you guys test fire your barrels (individually wrapped/sold BA barrels, not installed)? If so, are they test fired 1pc per sample lot (if sample testing, what AQL level is used?), or are all barrels test fired (100% testing)? And if so, what are some criteria are being evaluated in the test fire sequence?
The reason I ask concerns my considerations on cleaning the barrels prior to installation and larping around the house lol, and potential small amount of lead exposure for around children and others in the house.
Grow a pair
Where is Sarah?
I have 2 BA handson barrels now, and when i put the coil pin the gas block is slightley canted! I know it will still get proper gas but my gas tube slightley rubs on my BCG gas key when it slides back into batt, i actually got it to line up straight by tapping it!
Hey man, where did you get the vise block?
Question??? I installed a Ballistic barrel,put the gas block against that shoulder and had a malfunction every shot,moved the gas block to line up with the gas hole slightly forward of the shoulder and no malfunction....So how did you say that it doesn't matter if you're up against the shoulder or not?????
So how to do choose a gas tube and how far should get go into the receiver?
so we went from put it on upside down to see holes lined up to tightening set screws…. did you just rotate gas block 180?
So why does BA recommend against dimpling the barrel for gas block set screws?
Well, like he said, incase you ever want to swap barrels or gas blocks. Personally, I considered this, one time too. When I started building, but then decided If I built a gun with a specific gas block, for THAT barrel. Then if I swapped barrels, I would just leave that gas block on it anyway. I always dimple my barrels.
But they do recomend to pin the gas block. Which totally defeats the purpose of easily removing the gas block!
What tool do you use to secure the receiver?
Just curious; how deep is the slot BA cuts into the barrel for the pin? Love you guys and own innumerable BA barrels in every available caliber. 👍
There's only a handful of companies making barrels. And a million rebranding them. They are all the same yet never the same. Mondays barrels are blems. And Thursdays barrels are perfect. Fridays barrels go in the trash.
@@wannabecarguy I don't understand how anything you said in your response relates in any way to my question.
Blumpy
Why do you keep the screws if your gas block if it's pinned? I took my screws out after I installed the pin.
What would be great is if you guys could gas a .308” barrel accordingly. 16” modern series midlength is ridiculously overgassed. I had to close my adjustable block halfway just to get it to respond. I had already dimpled the barrel for .450” and the adjustable block was .475”
Makes a guy a little pissy
So do you install your gas tubes after the block is on the barrel and do it that way? Or if my barrel/block isn't pinned , should/can I install my tube to gas block then install the block & tube onto the barrel? is one better?
Either way works. Personally I install tube on block first so I can also work on centering my tube in reciever channel while locating the block on the barrel. Just a personal preference deal.
@@waldo5661 I thought so, I do same. For centering and because I personally find it easier as well
If I'm working on the barrel, installing a muzzle device, gas block, etc, I'm securing THE BARREL, in the vise using polymer V blocks in the vise jaws to hold the barrel securely and not mar it. I think it's a bad idea to work on the barrel by holding the upper in a vice and even have the chance of introducing too much force/torque on the upper/barrel interface.
Help, this is my last hope I've got a barrel that is not drilled for the did system please help.
What tool do i need to adjust
The gas blocks I am finding do not have a hole for a pin, to pin it to the barrel. Where can I find one?
for the low price of 30$ and a hand drill, you can spend the same amount of time installing a dimpling jig, drilling a dimble, and installing your gasblock both perfectly square and center, and even more bomb proof.
Against Milspec to no gap a gas block. Thermal expansion means it pops the gas block.
Who is this Nordic Viking looking guy? Looks like Clint from Ballistic Advantage!... But he dissapeared years ago!? It must be THOR, the Hammer God of Lightning! 🌩
R like the barrel I have from ballistic advantage no gas port
I've seen videos telling you to not put the gas block all the way to the shoulder, so which one is it? Lol
: OUTSTANDING instructional information. 🐢 👍 🐢 😀
I wish you guys and Aero would actually dimple the freakin barrels that don’t come with pinned gas blocks. Like the late Larson told Aero.
why do you install the gas tube after the gas block???
BA Hanson Barrels with the Low Pro makes install a breeze. The barrels are very accurate and durable. Dimpling and pinning is not necessarily hard if you have the rights jigs but at the price point of the BA Barrels it does not make much sense..
‚use your brain‘, 😂 hahahaa, excellent, thanks a lot! straight an effective to what its about no bs. no ‚thanks to our sponsor‘