Starter replacement Dodge Caliber 2007-2012 1.8L 2.0L 2.4L Jeep Install Remove Replace
Vložit
- čas přidán 12. 09. 2024
- Starter replacement Dodge Caliber 2007-2012 1.8L 2.0L 2.4L Install Remove Replace. Removing the throttle body helps get it out.
2020 has really shown me I needed to be better prepared for the future, start saving/investing now. Use some of that money U saved by watching DIY videos to plan for the future. Click to get started today.
Etrade - refer.etrade.n...
Get 2 free stocks with:
Webull - act.webull.com...
The procedure in this video should help you if you are doing several years and models, some are listed below.
2007, 2008, 2009, 2010, 2011, 2012
Caliber SE, Heat, Express, Mainstreet, Rush, SXT, R/T, SRT-4
Dodge Avenger 2.0L, 2.4L
Dodge Journey 2.4L
Jeep Compass 2.0L, 2.4L
Jeep Patriot 2.0L, 2.4L
Like the Facebook page, find me here. / fixingcarsandstuff
This Channel provides videos for informational purposes only and cannot be held liable for injury, damage, problems that arise when trying to duplicate steps shown in videos.
Outtro music snippet, by: joshwoodward.com/ Good To Go - Josh Woodward
creative commons license.
I just changed the starter on a 2008 Caliber
1. Disconnect battery both terminals
2. Remove Battery
3. Remove Battery tray completely
4. Lift front left wheel with Jack and brace with Jack stand under cross member
5. Disconnect air tube from airbox and throttle body and remove
6. Lay under car and remove bottom starter bolt
7. Remove upper starter bolt
8. Pull starter out of flywheel hole and turn to access wires remove them from starter
9. Remove starter and install new one
Thank you❤️
Badass man
Your video was great for helping me change out my 2007 Jeep Patriot starter. My jeep has the 2.4L so your process was great. Much appreciated.
THANKS --I HATE NEWER CARS---HATE COMPUTERS AND MISS CARBS
Shalom Aleichem
That's why I drive a 1992 Ford Ranger. I also have a 1976 Chevy G-10 Van that's been in my family since 1976 (mom and pop {RIP} bought it in '76) that has 850,000 miles on the original drive train. I'm gonna restore it.
I also have a 1972 VW Karmann Ghia that I've completely redone. Also a 1981 Harley Davidson that will be up and running again soon.
I've been a mechanic for almost 50 yrs and I've seen automobile's go from simple to ridiculously complicated. Someone forgot the old old adage that simplicity is the ultimate in sophistication.
Automobiles aren't getting more efficient, they're getting more complicated and extremely expensive.
I had a 1967 VW that got 32 mpg and that was in 1970. I could tear the engine out at 0600, rebuild it (stock) and have back in the vehicle and running by 1800 and that after taking a few brakes during that time period.
In 1989 I paid $25,000 for my house and took 10 yrs to pay it off. Automobiles are costing more than my home and taking 7+ yrs to pay it off.
Auto's today are mostly JUNK!!! Expensive JUNK!!!
Of course a fiat currency doesn't help, but really this is ridiculous.
Baruch haba b'shem YaHuah
AAPiY
MiKaEl
I just did the two days ago you should have took the intake off and you should have took off the radiator fan off as well
I've done this multiple times never had to touch the throttle body to change the starter . 07 dodge caliber rt
Ok I'm confused about the two bolts holding the starter. Is there a site for a diagram?
Thanks so much for making this video!
You do not need to pull the throttle body only the breather box tube going to the throttle body to many wasted steps here .
lori deyo
Did you perform this same job with out removing the throttle body?
lori deyo I was thinking the same thing
that tube goes to the bottom of intake manifold, but yes it is a evap line straight from the evap valve/solenoid
Awesome job 👍
Could I keep the throttle body in and still be able to take out the starter?
Where does the yellow starter wire connect back in at?
It's the plastic piece at the bottom of the intake hose elbow that holds the wire going to the throttle body. If I can't get it off I guess I could cut it out then just zip tie the wire afterwards. Thanks.
I've been told by several mechanics to change it from the top because it's easier
They broke my plastic part that red positive part where that darkish green wire is i was wondering what can i use to put it back
ohhh gewd larwd jesus for this video.. awesome
Hi Please can you help. i just had my egr valve replaced on my Dodge Caliber 2007 and the garage couldn't figure where he need to put once air cable. i can send the picture of the cable to you if you don't mind
saved me some money brother,big up too your video....have a brew on me.🍺🍺🍺🍺🍕🍕🍕
a 2009 is pretty well same concept, yea?
I got a quick question
Hey , I replaced my starter aswell , it starts fine and everything. but now I'm hearing a rattle when I'm driving from a low speed to a high speed.. do the gears in the starter need to be set a certain way putting it in or ?
No mames
How much would you charge for labor for a job like this?
Can you post a video on replacing the starter on a jeep patriot cause this video says it but cannot see when you switch vehicles
Because jeep patriot and dodge caliber we have the same parts
How long that take for you to replace the starter.
Shalom Aleichem
What about removing the battery completely and the breather box, wouldn't that help make more clearance?
Baruch haba b'shem YaHuah
AAPiY
MiKaEl
Yes they do its way much better
Hi there, You know that "stupid thing"? How do you get that off? It is driving me crazy. lol.
I don't even remember what exactly that is, are you talking about a hose, or maybe the plastic holder. I realize the video is not 100% in focus for that particular part. at about the 2 min mark.
Hey can you help me... I replaced mines and put battery cables back on and it did not crank..... Then I unhooked the neg. cable for a few minutes it started fine cut off and tried to start it and it wouldnt start. So do the computer need to be reset?
Anthony Lovelace Why did you replace the starter? For the reason you are experiencing now? Likely not a starter problem, maybe ignition switch, safety or clutch switch or computer problem.
It wouldn't start unless I hit the starter....
need to make sure the connections at the battery are clean and tight and you of course have a good battery. I think the computer is tied into the starting system , not sure exactly how though.
Okay thanks!
Anthony Lovelace nbznnxzndA. A. DMA
Qughju
Ese motor esta asqueroso...deberian limpiarlo antes...
What a junk! The newer the cars the worse the engineering.
saved me some money brother,big up too your video....have a brew on me.🍺🍺🍺🍺🍕🍕🍕
saved me some money brother,big up too your video....have a brew on me.🍺🍺🍺🍺🍕🍕🍕