Brilliant thank you, love the colours and texture, though it looks like it's also a good idea to start at the top and wait for the bottom to set a bit more
Solo son piedras de río con cemento de pegar cerámica... y para el brillo el con un barniz para con concreto que lo encuentras en cualquier "ferretería" no se lo como le llamen tu pais.
Beautiful installation and thank you for the video. I will certainly use this on a cinder block fence! I also have a concrete porch I would like to top with cracked plates. Would I apply them the same way or how can I apply the cracked plates on my concrete front porch?
Thank you for comment. Cracked plates would have glaze on bought sides. The surface of the glaze is slippery and would not last long on the wall. The solution: treat the side of the plate with special primer ( tile on tile system primer) that side for adhesive to stick to or use constrictive grab adhesive like pgb and fill the gapes between plates with tile grout for exterior. I hope this information will help:)
I love the creativity of this but the rocks at the bottom are so slouchy and the top rocks have no slouch. I may try this in smaller sections using the fixative in patches leaving time to set better before the upper sections.Thank you for your video. 💕
I was using tiles adhesives and before used primer. If you think to use just mortar - sand and cement mix, then yes, spaying the water before application would give good adhesion.
I applied primer on one day, and started installation on the next day. I think it depends on primer you are going to use. You should let primer to dry completly before installation
Yes, it could be on the patio as well, but it would be better to use concrete instead of tile adhesive. Sharp sand and cement mix 3:1 ratio mix + water , mix it. When, press the pebbles into the fresh concrete. It is better to use cobbles, it is easier to walk over bigger stones, when small. I hope it will help. When I have time, I could create video how to do it:)
I wouldn't be able to tell exactly, because i used leftover , but 1bag would be enough for 2.5 square metres or 1foot x 16 foot. It depends on pebble size and depth of the adhesives you apply. I hope that helps:)
Bravo! The pathway were done like professionals. I'm currently renovating my entrance and this is a great inspiration.
Thank you:)
Good job Loreta. 👍I will also try this at my home. Love from India
Keep up the good work!
Beautiful!
That's cute. And You Work SO FAST😁☺
Brilliant thank you, love the colours and texture, though it looks like it's also a good idea to start at the top and wait for the bottom to set a bit more
Thank you, thank you for advise:)
I didn't know you could get stones to stick in the mortar like that. That looks so beautiful. I want to try this now. Thank you 🤗🌻🌺🌷
Is it mortar that’s being used?
🍃👌🏽🍃
@@MoonLeaf_RaquelLeBaudour Mapei Keraflex Sg Mortar
Use a tile set as it's strongest 💪 👌 💯 😊
@Raquel LeBaudour a tile set mortar or regular thin set but don't mix it to soupy.
Brilliant!! Will have a bash at doing this... Thank you!!!
Really inspiring thank you
It would help if you put a list of ingredients in the description box.
Solo son piedras de río con cemento de pegar cerámica... y para el brillo el con un barniz para con concreto que lo encuentras en cualquier "ferretería" no se lo como le llamen tu pais.
Love it, I'm really impressed 😊
Thank you.
Gracias, que lindo queda🤗
That is absolutely amazing love it xx❤️
Thank you very much:)
it's so nice ❤️
Thank you very much, this is very useful information
Amazing! 👏
Thank you:)
❤❤❤the Best
I was looking for a pathway application. Nice job though
Great work Loreta! Looks beautiful. Can it be done on a big wall ?
Yes, why not, because it is the same as ceramic tiles instalation
Beautiful installation and thank you for the video. I will certainly use this on a cinder block fence! I also have a concrete porch I would like to top with cracked plates. Would I apply them the same way or how can I apply the cracked plates on my concrete front porch?
Thank you for comment. Cracked plates would have glaze on bought sides. The surface of the glaze is slippery and would not last long on the wall. The solution: treat the side of the plate with special primer ( tile on tile system primer) that side for adhesive to stick to or use constrictive grab adhesive like pgb and fill the gapes between plates with tile grout for exterior. I hope this information will help:)
I love it!! maybe the mixture would have been a bit thicker.. 🤔 But, I don't know anything about this, so just an inexperienced thought..😊
Nice
I love the creativity of this but the rocks at the bottom are so slouchy and the top rocks have no slouch. I may try this in smaller sections using the fixative in patches leaving time to set better before the upper sections.Thank you for your video. 💕
Very Good ❤
Thank you;)
Amazing!!!!
Joder , queda wapo hasta para un salón
Thanks
You are welcome:)
Wowww
What is the adhesive material you are using to stick the pebbles to on the wall? -Thank you! Beautiful!
🍃👌🏽🍃
I used keraflex maxi s1 mapei, but you can use any as long as it is for exterior application
What?
What
I think its mortar
Good
Super 😍👌💪
Thank you
Bagus bro.
Any thin-set would work, or the one that you are using only?
What would you meen by thin-set?
Good job, very nice! how long did the whole thing take you? how many square meters (or feet)?
Thank you. It is 4 square metres about and it took to do all the job about a week. If you have perfect condition and no rain it would take 4 days.
Wow
If I had to guess, wouldn't it be a good practice to spray water on the concrete surface before putting the mortar on it?
I was using tiles adhesives and before used primer. If you think to use just mortar - sand and cement mix, then yes, spaying the water before application would give good adhesion.
good
Пожиже клей надо было делать!
How long do we have to wait after applying the primer? Or does it dry within half an hour or so?
I applied primer on one day, and started installation on the next day. I think it depends on primer you are going to use. You should let primer to dry completly before installation
Thanks
Hi great work, how many kgs of pebbles did it take ?
Hi, thank you, I used about 60kg of pebbles.
Could this be used on an outdoor patio. On the floor?
Yes, it could be on the patio as well, but it would be better to use concrete instead of tile adhesive. Sharp sand and cement mix 3:1 ratio mix + water , mix it. When, press the pebbles into the fresh concrete. It is better to use cobbles, it is easier to walk over bigger stones, when small. I hope it will help. When I have time, I could create video how to do it:)
Could this be done on drywall as well?
Yes, if it would be done for interior, it would be the same as tiles installation.
what did you put on top? Thank you
Sealant
Can you describe the mixing of this?
It is the mix of tile adhesive.
thats awesome
Thank you
Ceverness😀🌹🌹
طريقة وضع الحجر تكلف جوهد ووقت اطول هل من طريقه اسرع 🤔 رغم ذالك يبدو المضهر جميل ❤
mape 1bag how many ft?
I wouldn't be able to tell exactly, because i used leftover , but 1bag would be enough for 2.5 square metres or 1foot x 16 foot. It depends on pebble size and depth of the adhesives you apply. I hope that helps:)
thank
1bag 480cm-500cm?
1bag- 40cm x 500cm about
mapeo keraflex maxi s1 can do 400cm-500cm?
Era meglio che non faceva nulla. Per posare così male e meglio non fare
Nice
Thank you