Mig Welder Wire Stuck In Liner
Vložit
- čas přidán 6. 09. 2024
- Mig Welder Wire Stuck In Liner are you having mig welder liner problems ? mig welder liner replacement is very easy to do and is quite cost affective but sometimes in the middle of your welding you get your wire stuck in the liner. Checkout my video and I will show you how easy it is to unjam your binzel liner. But most of the time I just buy a new one as its cheap and can make a huge difference to your MiG welding outcomes. Also once you damage your liner its almost impossible to get your wire flowing through it with out jam-up's or snags. You can damage it as easy as running over it or bending in a tight loop also the longer your mig welding torch liner the more issues you will find with your wire. The shorter the better.
Check Out More Cool Stuff : petes-tools.com
Binzel liner, mig welder liner replacement : • Video
Adjusting your drive roll tension : • adjusting your drive r...
PRO Liner : amzn.to/32R6WWP
Pete, thank you so much! I’m a girl with a new MIG welder, and I had so much fun the first day I ran through an entire 2 pound roll of wire. But when I went to change out the wire, the wire was stuck. I thought I’d royally screwed up. This was such an easy fix, and I thank you so much for putting this video out! Super understandable, super chick friendly… I appreciate you so much.
Wow very cool .Sorry i am so late with reply .I have been working on another channel about new Zealand
Thank you! I am brand new to welding and thought I messed my welder up pretty good. Found your video and it was a super easy fix. Going to have to check out more of your videos.
Glad it helped!
Great stuff as usual Pete.
One other thing I've found that can jam your wire also is if the wire gets a light coating of rust on it. I live in a high humidity area and the wire can get a light coating of rust on it when it sits for some period of time. To overcome this I use a special lubricated felt wire cleaner that clamps onto the wire where it comes off the reel. Works a treat.
Thanks for the info!
cheers pete
Thanks Buddy.
Got welding wire stuck both ends bust both ends leaving very little to grab with pliers. Followed your instructions and as you guys say "no worries "
Thanks very much, all the best from David in the UK.
Nice work! cheers David NO WORRIES MATE LOL
Thank you, you saved my job, I'm new to welding and I had no idea what to do.
Glad I could help
You are the only person I could find that addressed this issue
thanks mate
Thanks Pete! That worked like a charm - I thought the thing was corroded or something much worse. Bob is indeed your wombat!
cool mate cheers
That's peet for help me with my wire kink. The wife was trying for the longest time to unlink my wire and boom peet does it just like that. Life saver
LOL Cool have great day
The best tutorial ever. Ty my Miller was very stuck.
Glad it helped!
I was just about to give up ! And just use my stick welder less problematic ! But thanks for this video I’ll tackle it tomorrow lost hours this afternoon with this stuck wire grrrrrr
LOL hope you sort it
For such a small welder (160A-200A), Can we replace the torch line from originally like 3m to 5-8m without an issue on motor feed power or poor arcing?
It's a big help for us new users.
awsome man thanks now i know how toi fix mine if it happens and what line my wier comes out cus my little plastic hose is brock and has to be i air line hose not the feeder hose
Did it work?
This actually helped a lot mate thanks
Brilliant video thank u 😎😀💡👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍
Glad you enjoyed it
Perfect guiding video - exactly what I needed today, Yay!
So glad!
Thanks Pete, just what I was looking for!
If you are getting wire stuck in the gun there is a bigger problem going on Pete. First off you probably need a new linner because it has probably been neglected, secondly you need to use wire lube they sell sponges that go in your welder by the spool. Also you need to use contact tip gel. With all that being said I have NEVER had a mig welder birdsnest with steel and I weld with it every day. Preventative maintenance, YEEEHAA!!
Nice
Thank you man i am new in welding it will help me in future
Best of luck
Thanks for advice sir .so good
So nice of you
In short, straighten out the whip and pull on the wire until it comes out. I don't see all that disassembly really doing much. Appreciate seeing that it will pull out though and that it's likely a kink. I was wondering how it would get stuck.
Just came back from the garage. Straightened the whip, snipped between the roller and the liner, went to the trigger end and pulled firm and steady and it slid right out! And you were right, a kink about half way through. Thanks again!
No worries mate
Hey thanks, your video helped me out. I had no ideal how to get that wire out till now! : )
You are welcome!
This helped us lot.. thank you dear
Glad it helped
There is no wire stuck in the liner, but I cannot get the wire to go through. It somehow became blocked while sitting on the shelf with nothing in it.
Thanks!
thanks
This video saved our day!
Thank you very much for the video!
Great video, the "Yee-Hahs" mess with my tinnitus badly.
cool mate , sometimes a bit loud lol
Great video thank you for sharing
Thanks for watching
Thank you
Thanks the video really help me out got my Miller up & working again
Glad I could help
Thanks mate - Good explanation.
No problem 👍
Thanks, that was helpful
Great thanks
Thanks mate, helpful.
Thanks
Thanks for watching
Thank you so much for the great video Pete, you just saved me🙏🏻
Thanks mate
Thanks Mate
what do you do if you have 2 lines inside it and both are snapped off at bother ends?
2 lines?
Love the videos Pete
Very informative
Glad you like them!
huge help, cheers
welcome
Helped me today thank you!
You're welcome!
thanks pete!
welcome
Thank you sir
Saved my day! Thanks!
welcome
Thanks for the tips Pete! You’re a wild man! Yee haa!! Where u from bro?
I am! LOL .CHRISTCHURCH MATE
thank you so much. this video helped me today!
You're so welcome!
im having the same problem ,,, i was going to junk my mig welder .....or try and find that whole piece .
did you fix it ?
@@petestools yes ..new part works great for now
Fantastic video thank you❤️👍😎
Thanks for the visit
where do you get new liners from?
amazon
My mig weld gun just bloked right on the tip of the nozzle..I removed the nozzle .but how can I clean it to reuse again?
That can be a real pain mate .You might have to replace it.
Important class 👍💪 thank you
Thanks
Thanks mate. Good on ya!
CHEERS
Hey i have flux 125 welder from harbor freight and i used the wire that came with it and it worked fine my welds were good but i let it sit for about a week and i think the wire rusted inside and it got stuck pretty well and i yanked it out and got better wire but now it feeds out all wild and makes my welds look horrible do you think i ruined the hose liner ?
are you sure your wire tension is correct
What if wire is broken at both ends and none is sticking out to grab?
Pull your gun to pieces you will find the end some ware.
very helpful .. ill try it but i bet i screw something up .. thanks
LOL SOUNDS LIKE ME MATE
Yes Haw
Thanks Pete for a great video. But do tell me what would you do with that salvaged piece of MIG wire. It's too short to be used for the MIG but such a waste to be discarded?!
yea to short to use
Thanks man
Any time
Please can it be used for stainless steel pipe
Try to keep the cable straight and don't step on it or drop any thing on it I have never had wire stuck in the liner I have had a lot stuck in the tip especially 23 wire.
good tips thanks
What did you say "Right pain in the bum pete" something?
yea its a pain in the bum
I bought a welder today
Read the manual
It tells me to lay the gun and liner out flat to feed the wire, but the problem is i domt think i tensioned it properly
So it just ended up getting to a point in the line and just stops, like i dont know what is going on you can feel it getting to the gun and then just stopping then i went a little too far and fucked it
I went to pull it though the roll side and only about 10cm came out... so what then its not sticking out either side of the welder just get a new liner
nice
Show your support for my channel by treating me to a coffee! www.buymeacoffee.com/petestools
Handy as 👍
cheers mate
Saved my ass dude thanks
lol, very welcome mate
Eeeee haaaa😂
YEEEEE-HAAAA
Thank you
welcome
Thanks mate
Very welcome
Thank you for this!
Hi jack, your welcome
Thanks mate
Happy to help