Testing Filter bass mid treble circuit at home Thank You for watching my video! please kindly assist me to like share and subscribe our channel for more video...
The one's on the treble part is also the value of the capacitor that I mostly use or a 1µf.. Because 1.5µf is not always available here in our place.. :) Nice detailed review and you clearly stated the value of parts and the drivers...
Standard 2nd order bass, 1st order roll in/out for the mid and 1st order for the horn. A 1.5 uf cap for the horn? It must be 16 ohm. Mid is 4 ohm. Bass is probably 4 ohm too.
Este trabajo es empírico hay ecuaciones y fórmulas matematicas para hacer un buen recorte de frecuencias de sonido a voluntad, sin estar probando de todo.
Good video but still no links to where you bought everything, and nor any parts list break down on what you use. It would be most helpful to us to have that information so that we could do our own builds. Thanks very much.
Sir mere pas purana videocon ka cassette wala deck rkha h jiska speaker base audio wala h kya mai us speaker ko as a car woofer bana kr car k fit kr skta hu.....reply n thanks in advance
il condensatore sul tweeter e giusto per filtrarlo ma errato perche si deve limitare la corrente con una resistenza se l amplificatore e 200 watt vanno tutti sul tweeter abbrustolendolo- ciao a tutti
Was going to say there are charts available in all shapes and sizes in case you might need a different inductance value... But I realized the genius Bak Lai has probably authored volumes on the subject so I wont mention it.
inductor must be in series with the mid, it is meant to decrease the treble sound from the mid speaker and also helps to match the overall impedance, and if you are into that , then let me tell you that you can use an inductor paralleled to the tweeter.
Olá amigo de som eu entendo pouco,mas ouvi de um engenheiro que a bobina não pode ser muito comprida aproximadamente 3 vezes seu diamatro quanto mesmo esse valor melhor será a bobina por que ela dispersas o campo eu sou aparecido .
..to make tweeters sound sweet and keep from blowing them ..look into " run motor capacitors " oil in a can capacitors .. find .4 mfd and 50 DC ones are the best for under 50 watts. lower mfd for louder uses .but Hard to find.. like used with ''Vintage klipsch type E crossovers'' ..or ''oil in paper'' would work also.. like lespaul tone caps such as the bumblebee's.. talk about bell sounds ..wow klipsch no longer uses these in new or after 1988 systems ..alnico horns are the best for under 50 watts per chan ...1 watt = 5 watts with alnico ..real efficient but yeah man
Hello sir hamare pass Ahuja srx 500 Watt sound hai aur ismein network plate Ahuja AR 0422-1 laga hai jo ki kharab ho gaya hai Isko Kaise banaen yah dusra Banakar dikhayen Jo jo ise chal Jaaye aur Kitna kharcha padega jald se jald video Banakar bataen Aisa bataen ki do speaker aur ek Pita sath mein Chali
@@anindyamitra5091 To keep the overall impedance low and increase inductance, even without metal cores, one should use higher gauge wires for the coil. Anyway, the inductance should be only high enough to keep a certain range of frequencies away from the woofer. Good quality speaker frequency dividers NEVER use metal cores.
ACHO ISSO UMA BOBAGEM. SE VOCÊ COLOCAR UM CAPACITOR CERÂMICO DE 2,2 MF x 250 VOLTS. PARA TODAS AS TWETERS.NO POLO + .E DE 3,3MF x 250 VOLTS. PARA A CORNETA. NO + OU EM UM FALANTE, CONE SECO, ATE DE 8" PARA SÒ SAIR MEDIOS. NÃO VEJO PRECISÃO DESSA BOBINA. PERDA DE TEMPO.
The one's on the treble part is also the value of the capacitor that I mostly use or a 1µf.. Because 1.5µf is not always available here in our place.. :) Nice detailed review and you clearly stated the value of parts and the drivers...
two 1uf in parallel to a 1uf in series can make 1.5uf if needed
Mantul....super krative
nice idea my friend
Very nice 👍🏻👍🏻 🇮🇳 || Kuki
.70mm it says in the video about the gauge of the wire No. of turns also 164 turns. moreover, .71mm=22 SWG (google)
Hi Pass 6db/octave for treble
Band Pass 6db/octave for mid
Low Pass 12db/octave for bass
the coil for the bass pasted welded on the negative or positive
អរគុណបងសំរាប់វីដេអូនេះ
very good bro
Thanks sir
Standard 2nd order bass, 1st order roll in/out for the mid and 1st order for the horn. A 1.5 uf cap for the horn? It must be 16 ohm. Mid is 4 ohm. Bass is probably 4 ohm too.
Can I put
2 speakers 300wx2
2 tweeters 150wx2
1 midrange 150w
In 1 3way of dividing network 600 watts?
Cuộn này dùng cho bass bao nhiêu đại ca
Este trabajo es empírico hay ecuaciones y fórmulas matematicas para hacer un buen recorte de frecuencias de sonido a voluntad, sin estar probando de todo.
អត់ប្រើ រេស៊ីស្តង់ទេអីបង? 10 ohm 4.7 ohm
បាសដូចជាឮស្រាលតិច ។
very cool
Good video but still no links to where you bought everything, and nor any parts list break down on what you use. It would be most helpful to us to have that information so that we could do our own builds. Thanks very much.
No dicen cuantas vueltas tiene la bobina que realiza la bobina es un crosover
specs of the drivers pls sir.. impedance wattage watever they are..im a noob here
Beautiful work. The end result is wonderful.
What song is that 09:16 ? I liked it too.
ProjectV8 it’s a Cambodian song
@@chheangsovathana Thank you
can you use it on 4hms.
So that's how Klipsch speakers are made nowadays!
LOL
Sir mere pas purana videocon ka cassette wala deck rkha h jiska speaker base audio wala h kya mai us speaker ko as a car woofer bana kr car k fit kr skta hu.....reply n thanks in advance
nice video pro, Hope you products audios......
queria ouvir todos juntos
Jos
Muy interesante, sería bueno especificar las frecuencias de corte, gracias
31mñ4ñp4ódoDoLFñfkñriñ
ลมวาไปซื้อลำโพงบูทูช ในเซเว่น เพราะกว่าเยอะนะ
il condensatore sul tweeter e giusto per filtrarlo ma errato perche si deve limitare la corrente con una resistenza se l amplificatore e 200 watt vanno tutti sul tweeter abbrustolendolo- ciao a tutti
I've heard that air coil inductors are superior to iron core inductors, is that really the case?
The midrange is reversed, you soldered the inductor and capacitor on the negative terminal
HLA MUY BUEN TUTORIAL M LO PODES PASAR EN CASTELLANO GRACIAS SALUDO D ARGENTINA
Super
Boss im asking favor to you i have budjet already i plan make speaker can you teach me boss thankz
I dont recommend a 50v cap for the woofer use 100volt and above
Zeus Martin Sajol Bhai ek comment 3 baar Kiyun kar rehe ho
good
បងខាងបាស់បេីសិនដាក់កង់ដង់50v 10ufបានអត់ ហេីយបេីសិនមិនដាក់ គឺដាក់តែសែលបានអត់បង
SUPER
Hai
What's the specs for using it for teeeter
just amazing he forgot to show how many turns should you make the coil, size of the copper wire etc. everthing.
Yep, the induction, Henry's, and frequency of induction, produced by the number of turns, the width of wire, and the size of the coil.
3:33
Was going to say there are charts available in all shapes and sizes in case you might need a different inductance value... But I realized the genius Bak Lai has probably authored volumes on the subject so I wont mention it.
What ... what numbers AWG you use ..
watch 3:35.
បងទទួលរៀប crossover ហ្នឹងសំរាប់ជាវ ឬអត់?
FOR WOOFER 2.2 MFD 50 V or 22 MFD 50 V.....please confirm
crossover divide and filter audio sounds systems
Thanks for watching
Try putting the inductor in parallel with the mid, not in series.And slap one on the horn while your at it.
inductor must be in series with the mid, it is meant to decrease the treble sound from the mid speaker and also helps to match the overall impedance, and if you are into that , then let me tell you that you can use an inductor paralleled to the tweeter.
បងអ្នកខេត្តណា
Sir isme kitne turns or kitna thickness wala wire lena hoga
cuantas vuelta le as dado a la bobina
this man is showing his works but no clue link on parts...this man is waiting for us to say "how much"...ah ah no way sir....psychology 101
At home? Is that opposed to where you work?
នៅណានឹងបង
sir ele jobs is my favourite
Bhai ye aapan product banke sale karo ge kya i want this
ដាក់ដុំភ្លើងចឹងទៅលឺបុុុុុកមែនបង
បាទលឺបុក
DUDE, I'VE GOT A GOOD TWEETER IN A KLIPSCH R28F THAT WON'T WORK ON ONE SPEAKER........... COULD IT BE THE CROSSOVER ?
I know it's a year later but why don't you switch tweeter's & you will get your answer
Third
How dare you not play the whole system together! :)
ខ្មែរតើ ស្មានតែបរទេស
បាទ ខ្មែរយើងទេ
@@InnovationKH ញុមចង់អោយបងដាក់ជាភាសាខ្មែរវិញ
Mau tanya gan menggunakan elco apa bera uf untu bass & di solder ke min apa plus makasih
pake elco non polar gan .. kaki kanan kiri sama saja ....
Sueño esa musica
No dicen cuantas vueltas tienen las bobinas crosover en los parlantes y cual es el calibre del alambre
Minuto 3:32 y 5:04 amigo.
Saludos
en el minuto 333 lo dice 164 vueltas
Amigos la impedancia final es a 8 ohms?
@@daniello8956 eso para q es?
Olá amigo de som eu entendo pouco,mas ouvi de um engenheiro que a bobina não pode ser muito comprida aproximadamente 3 vezes seu diamatro quanto mesmo esse valor melhor será a bobina por que ela dispersas o campo eu sou aparecido .
..to make tweeters sound sweet and keep from blowing them ..look into " run motor capacitors " oil in a can capacitors .. find .4 mfd and 50 DC ones are the best for under 50 watts. lower mfd for louder uses .but Hard to find.. like used with ''Vintage klipsch type E crossovers'' ..or ''oil in paper'' would work also.. like lespaul tone caps such as the bumblebee's.. talk about bell sounds ..wow klipsch no longer uses these in new or after 1988 systems ..alnico horns are the best for under 50 watts per chan ...1 watt = 5 watts with alnico ..real efficient but yeah man
How did it sound all together?
Keep walking bro!
doi trep ken bao nhieu tien
LA DEMOSTRACION SE HACE EN UN SOLO PARLANTE PARA VER EL EFECTO REAL QUE CADA FILTRO PRODUCE.
Con y sin filtro para notar la diferencia, si es muy funcional pero no hace las comparaciones . Saludos.
oye y que pasa con el embobinado eso no suma ohmios ? por que me da miedo conectar esos filtros sin saber si dañare mi ampli
@@cavernetblack9037 creo que no, pero si que necesitaras mas potencia para moverlos
¿por qué el capacitor en paralelo en el woofer me corta los agudos de todas las vias? Gracias.
entah kenapa aku ingin tertawa
Hah
queria corta o grave do galante
Hello sir hamare pass Ahuja srx 500 Watt sound hai aur ismein network plate Ahuja AR 0422-1 laga hai jo ki kharab ho gaya hai Isko Kaise banaen yah dusra Banakar dikhayen Jo jo ise chal Jaaye aur Kitna kharcha padega jald se jald video Banakar bataen Aisa bataen ki do speaker aur ek Pita sath mein Chali
បងខ្ញុំអោយបងដាក់ចំណងជើងជាអក្សរខ្មែរបានបងអត់ព្រោះខ្ញុំចង់អោយបងជួយលើកដំកើនអក្សរខ្មែរយើងបង
How to know the wattage of speaker
What is the metarials
Mare pas100 watt ka woofer ha os ko bass coil lagwne ha Moja bass coil chahiya
السلام عليكم اخي محتاج دائرة بيز
NO [MUSICA]
Bass me lag jaye ga kya 18,, ke mee
No wire guge number
No wire trun number please full detial now you.
watch 3:35.
Heheh. 🤣Watch full video
I don't think you have enough commercials in your video
Okok
Coil gauge ?
6inch mid reng bass less capasitar vellyou tellmi how much ug and volts
What is the function of capacitor here??
Capacitive reactance is being used in cross-over circuits, as well as inductive reactances.
Can you give me the formula of steel core coil ? thank you
Using metal as core for audio coils is totally not recommended. It causes distortions in the sound. Use air or plastic instead.
but that would increase the overall impedance and decrease the inductance.
@@anindyamitra5091 To keep the overall impedance low and increase inductance, even without metal cores, one should use higher gauge wires for the coil. Anyway, the inductance should be only high enough to keep a certain range of frequencies away from the woofer. Good quality speaker frequency dividers NEVER use metal cores.
@@ManoelNunesOSan, okay, I got it.
@@anindyamitra5091 eso son barras de hierro silicio y si son recomendadas
Y no importa si las boinas no son de los mismos ohs????
Berapa meter kawat yang dibuhkan pak
ภาษาอะไร
? Medidas ?????
Mmmmm
Какой же ты медленный!!!!!
3 bucks on ebay or auto zone for free
ever hear of HYSTERESIS? metal core in audio is really bad.
Cuantos metros de alambre son y de que calibre
Exacto en metros cuanto equivale?
Tho y nung
This is a CZcams demonstration. At least make a little effort at tidiness.
164 turns=w
ACHO ISSO UMA BOBAGEM. SE VOCÊ COLOCAR UM CAPACITOR CERÂMICO DE 2,2 MF x 250 VOLTS. PARA TODAS AS TWETERS.NO POLO + .E DE 3,3MF x 250 VOLTS. PARA A CORNETA. NO + OU EM UM FALANTE, CONE SECO, ATE DE 8" PARA SÒ SAIR MEDIOS. NÃO VEJO PRECISÃO DESSA BOBINA. PERDA DE TEMPO.
no entiendo una mierda su idioma like si no lo entiendesXDXDXDDDD
Ricardo Cifuentes yo no entendí ese enredajo
@@estebanperez2435 yo quisiera saber como calcular las vueltas de alambre para el bajo es que quiero hacer el corte en 100 hz
Fek
eres mudo. porque no explicas