Works! This only took a few hours to do. I will say there are a LOT of things to get square if you really want it to look good, but despite some slight variations from square, mine works fine. I made mine bigger (300 mm length for the "arms"--the piece you make 4 of) and adjusted the other pieces to suit. I will likely add a second set of cords connecting the bases opposite the one set illustrated in the video. As built, it will "fall" if you put something down on the top near the one set of cords that is shown. In any case, a great video that answered nearly all of the questions I had about building one of these and did allow me to complete the project I had visualized. Cheers!
Dear Sir! Great job! Very nice and clean the way you work: as a lesson of how to do things right! I've made one like your and is a great success! Thank you vey much!
As long as the top is in level it does not colapse. To make it 100% safe, you would have to attach a string to each corner. However this would ruin the "magic".
When choosing the lengths or distances, are there any rules to follow, such as be sure the short piece of wood is more or less than 1/2 the length of such and such or the short string has to be exactly in a certain place?
Inquiry Sir, I'm thinking about doing this for my mailbox base. is the top always wobbly or can it be stabilized by tightening the chord/ chains/ wire? Gratitude.
Hello, the top is quite stable as long as you do not tilt or tend it. As you can see in the video the top is stable enough to carry my cam. Best regards
Hey idk if you found out the answer but for other who may come across this, the short answer is because the center of balance is not in the middle, rather it is offset to the side opposite of the long strings therefore the top of the table wants to pull out and away from the long strings. Since it can’t, it stays in place. It is worth noting that this type of design holds drastically less weigh and is susceptible to tipping over to the side of the long strings if enough force is applied
Make them as long as you wish. Just determine the 'center' cord first and go off of that. Longer is less stable but should hold. There have been foot bridges designed using the principle of tensegrity.
Works! This only took a few hours to do. I will say there are a LOT of things to get square if you really want it to look good, but despite some slight variations from square, mine works fine. I made mine bigger (300 mm length for the "arms"--the piece you make 4 of) and adjusted the other pieces to suit. I will likely add a second set of cords connecting the bases opposite the one set illustrated in the video. As built, it will "fall" if you put something down on the top near the one set of cords that is shown. In any case, a great video that answered nearly all of the questions I had about building one of these and did allow me to complete the project I had visualized. Cheers!
2:43 2:44 2:44 2:49 2:51 2:51 2:51 2:54 ⅞6😢
This looks amazing 😍 Can I make one using 35mm x20mm wood bars? Or, do they have to be square??
Tensegrity RELIES ON GRAVITY to work
So basically, the middle string holds all the weight of the top structure, and the strings on the side just balances it so it doesn't topple?
Exactly. Some people would use four 'long' cables to make it much more rigid but it depends on what effect you want to achieve.
beautiful friend
Dimensions for the drill holes ;great work!!!
4mm. The side that contains the knot i have drilled out a little bigger.
Very good
Dear Sir! Great job! Very nice and clean the way you work: as a lesson of how to do things right! I've made one like your and is a great success! Thank you vey much!
Hello sir 🤝🤝
Asılan iplerin uzunlukları nedir acaba.
its so nice . can You make it double size? Will it still work?
Great! Thanks for the instructions!
this can colapse in one direction right? because for a tensegrity to be completely stable it needs 3 outer cables
As long as the top is in level it does not colapse. To make it 100% safe, you would have to attach a string to each corner. However this would ruin the "magic".
Muy bueno... parece que lo más difícil es el balance final.
which is the name of the instrument where you insert the meter do draw the cross on the wood ?
nicely done
When choosing the lengths or distances, are there any rules to follow, such as be sure the short piece of wood is more or less than 1/2 the length of such and such or the short string has to be exactly in a certain place?
There is no specific rule. The centre string can be set up as you wish. The other cords then become correspondingly longer or shorter.
@@creativeatolye5812 ty
Üstadım ellerine sağlık. Çok güzel olmuş.
Fascinating.
Great job
Pretty cool
Beautiful
İpin uzunluğu ne kadar acaba
#1
What kind of glue did you use ?
I used UHU wood glue.
Muy bueno gracias lo are en casa 👍🏻👍🏻👍🏻👍🏻👍🏻🇨🇱🇨🇱🇨🇱🇨🇱🇨🇱🇨🇱🇨🇱🇨🇱
hola, las cuerdas miden todas iguales gracias de antemano
Klasse, vielen Dank!
Sir pl. Measure the wood.
Inquiry Sir, I'm thinking about doing this for my mailbox base. is the top always wobbly or can it be stabilized by tightening the chord/ chains/ wire? Gratitude.
Hello, the top is quite stable as long as you do not tilt or tend it. As you can see in the video the top is stable enough to carry my cam. Best regards
Use four outer cables if you want more rigidity.
Sir pl.measure the wood.
멋져요. 잘봤습니다.
Vou fazer um desses com certeza. Muito show
👍👍👍👍
What iff the wood thickness is 35mm x35mm?wil it still work
yes, should work.
Looks cool but I bet it still wobbles.
Maybe the first 2-3 seconds. after that it does not wobble anymore. ALso visible at the end of the clip
Vc pode passar a medida da da madeira pofavo queria fazer uma do mesmo tamanho ??????
Fiz o meu agora esperando verniz secar vou por cordas de nilon fica melhor quase invesiveis
Vou fazer em nylon tbm
👍👍👍
how does that still work with only 2 of 4 corners of base suspended with the strings? I thought all 4 corners connected were necessary for it to work?
Hey idk if you found out the answer but for other who may come across this, the short answer is because the center of balance is not in the middle, rather it is offset to the side opposite of the long strings therefore the top of the table wants to pull out and away from the long strings. Since it can’t, it stays in place. It is worth noting that this type of design holds drastically less weigh and is susceptible to tipping over to the side of the long strings if enough force is applied
@@mikeydoesthings7877 oh OK thanks
Muito bom.!
why no measurements?
How did you fasten Glass to Wood?
With a drop of glue.
unique
I didn't notice this antigravity.....
Wow
a lesson in what happens when you don’t clean up your glue.
👌
⭐🌟⭐🙏⭐🌟⭐
Hey Creative Atolye, how long should the strings be?
Exactly twice the length from the centre to one end
@@MrWhitelines There's a smart aleck in every crowd. LOL
Make them as long as you wish. Just determine the 'center' cord first and go off of that. Longer is less stable but should hold. There have been foot bridges designed using the principle of tensegrity.
Geo
Ни размером ,ни объяснения,дизлайк за это,и пять за изделие!!!))
But not stong
MUSIC STINKS BAD.
👍👍👍👍