I strongly advise people to read the manual that comes with this compressor. The Heat Guage requires round silver oxide batteries or it will not work. The sensor end of the heat guage goes into the back of the primary stage, ( back of lower part of the aluminum part of the compressor pump). DO NOT over fill the compressor with hydraulic oil AW 46. Keep a close eye on the oil window fill to the red mark at the half way point. Less or more can damage your compressor. Watch as many videos as you can find so you will be familiar with setting up, power up the water pump before turning on the compressor, leave air valves open for a minute before closing them. Lubrication is key to keeping it running smoothly so check oil level before using every time, change oil as per manual or when it becomes dark in color. Keep moisture out of your tanks by using additional filters.
I'm just new user of smart digital edtition. It works great but it doesn't stop at the stop pressure. If I press START key, the actual pressure goes high but never stops at the stop pressure. It stops at the temperature I set but not pressure. Any advices are welcome!
Hey, whats the normal work temperature for this compressor?. Mine got up to 52 with 3200psi on the gauge.... I stopped and let it cooling down for a while... Some videos shows 60°C....
You should do a troubleshooting video of your compressor. I just received my compressor from you, and there is an air leak on the left side . It will not build pressure past 2200 psi . You should also let us know what temperature is too hot ?
There is a parts diagram which is shown in the manual that comes with this compressor. Use it to find the part you need and order the part number assigned to it. Aliexpress provides some parts, filters and accessories.
WARNING: I had a Young Heng compressor rated for 300 bars (4250 PSI), I used this compressor to top of my air tanks to 300 bar which my air rifle requires. The crank case where the compressor cylinders attach fail and exploded throwing the pistons and case framents flying. The rupture disk did not fail. The air pressur reached 4,250 PSI as I reached to open the pressure blow down valve and close the air tank valve the explosion occured. The machine oil level was check before running, the water circulation was checked and found acceptable. In addition I was montering the machine running temp. and was at 57C to 60C all item were in the acceptable perimeter as specified by Young Heng manual. I used this unit for a year about every two weeks. In my oppion the aluminum case is to thin and cannot stand up to the stresses caused with frequent use.
Did you have the crankcase breather installed? I've seen countless complaints like this and every time, the original plug is still on the crankcase filler (where you pour oil in). If it can't exhaust that build up pressure, it's going to go BOOM.
@@hurricaneaquatics Yes it was intalled. The aluminum case cracked where the piston cylinder attached allowing the complete piston culinder, head and piston to fly apart.
J'aurais une question je viens de m'apercevoir sur la vidéo effectivement il va falloir mettre de l'huile C'est là que je me rends compte que vraiment pour une bouteille de plongée à charger ce que ça me coûte alors là je savais pas dans quel genre de Bidon d'huile faut-il que j'achète est-ce que vous avez une référence Parce que je suppose des que je vais la recevoir elle sera vide ski normal
? quel genre de bouteille d'huile il faudrait pour Yonntech Pompe à air comprimé à haute pression, 300BAR 30MPA 4500PSI Fusil de système à contrôle automatique Compresseur
SECOLUBE 500 or equivalent. Dont use hydraulic oils; they're for heavy machinery sealed systems. Secolube is a breathing air compressor specific oil designed so it doesn't ignite on the second stage of compression. Its pricey, but it'll make your compressor last longer as well as making your high pressure guns last a lot longer since there's no toxic particles entering your gun
Mine just hums when I turn it on. Brand New today, and it doesn't work. Why wouldn't one of these things start. Btw, the water pump doesn't work either. It hums to, but I think it needs to be primed, but how?
@@hengyong820 I don't understand why you gave me your #. I live in, America, and I don't believe I have the capability to call it with my current phone plan. All I know is, this is a brand new matching, but it hums when I turn it on, and the fan now wants to turn but stops. I try to help move it along, but no dice. Do both of the pressure valves have to be tight, or lose when I start this thing? I don't want to damage it.
Ce qui m'intéresse est de gonfler une carabine PCP sans paser par une bouteille "tampon". Une vidéo sur le sujet m'intéresserait. Pour info, carabine stoeger PCP XM1 20 joules) merci toutefois.
@@joshuagibson2520 It's not broke it's brand new but I had some questions about it ! And the email address in the owner's manual for a brand new compressor the email address for Hang Hang is a invalid email address !
Hello sir, the cooling on this compressors is not smart, there must be a second water inlet and outlet on the opposite side! Even when its cool from the front, the back gets very warm, so you have to use extremely cold water to hold this in tolerance. I made this second in and outlet by myself and bought a more powerful waterpump, now it can be used much longer and the piston rings don´t begin to melt, this happened a few times in the past because of inappropriate cooling method that was before, when the piston rings melt it gets stuck and the rocker ripped apart. But now i have another problem, the motor seems to have lost some of it´s power :( it shuts down a few times, before i get to 4500 psi
Best detailed setup instruction thanks shows how to set up temp gauge properly
I strongly advise people to read the manual that comes with this compressor. The Heat Guage requires round silver oxide batteries or it will not work. The sensor end of the heat guage goes into the back of the primary stage, ( back of lower part of the aluminum part of the compressor pump). DO NOT over fill the compressor with hydraulic oil AW 46. Keep a close eye on the oil window fill to the red mark at the half way point. Less or more can damage your compressor. Watch as many videos as you can find so you will be familiar with setting up, power up the water pump before turning on the compressor, leave air valves open for a minute before closing them. Lubrication is key to keeping it running smoothly so check oil level before using every time, change oil as per manual or when it becomes dark in color. Keep moisture out of your tanks by using additional filters.
I'm just new user of smart digital edtition. It works great but it doesn't stop at the stop pressure. If I press START key, the actual pressure goes high but never stops at the stop pressure. It stops at the temperature I set but not pressure. Any advices are welcome!
a newer model with a different power cord and pump attachments,is there anything else that is upgraded
Please make a video second stage piston seal replacement
Thanks SteveK
This is is the fancy version that has the electrical outlet on the side for the water pump and auto-shut-off feature. I got the cheaper one lol
Hey, whats the normal work temperature for this compressor?.
Mine got up to 52 with 3200psi on the gauge.... I stopped and let it cooling down for a while... Some videos shows 60°C....
You should do a troubleshooting video of your compressor. I just received my compressor from you, and there is an air leak on the left side . It will not build pressure past 2200 psi .
You should also let us know what temperature is too hot ?
Queria saber qual o capacitor usado no compressor yong heng
does he not sell on ebay anymore? can't finy any
more like assemble compressor. Wish to see actual filling proceedure of tank.
Thank you! You saved me from having to sit through the whole video! For that, I salute you!
You have a parts list? I have the compresor i just cant find the red and chrome part that put the air into the tank.
There is a parts diagram which is shown in the manual that comes with this compressor. Use it to find the part you need and order the part number assigned to it. Aliexpress provides some parts, filters and accessories.
I think the red and chrome part you speak of is actually the valve and it stays attached to the tank. It’s not part of the compressor.
WARNING: I had a Young Heng compressor rated for 300 bars (4250 PSI), I used this compressor to top of my air tanks to 300 bar which my air rifle requires. The crank case where the compressor cylinders attach fail and exploded throwing the pistons and case framents flying. The rupture disk did not fail. The air pressur reached 4,250 PSI as I reached to open the pressure blow down valve and close the air tank valve the explosion occured. The machine oil level was check before running, the water circulation was checked and found acceptable. In addition I was montering the machine running temp. and was at 57C to 60C all item were in the acceptable perimeter as specified by Young Heng manual. I used this unit for a year about every two weeks.
In my oppion the aluminum case is to thin and cannot stand up to the stresses caused with frequent use.
Did you have the crankcase breather installed? I've seen countless complaints like this and every time, the original plug is still on the crankcase filler (where you pour oil in). If it can't exhaust that build up pressure, it's going to go BOOM.
@@hurricaneaquatics Yes it was intalled. The aluminum case cracked where the piston cylinder attached allowing the complete piston culinder, head and piston to fly apart.
@@davidhagerman7165 ouch, sorry to hear!
J'aurais une question je viens de m'apercevoir sur la vidéo effectivement il va falloir mettre de l'huile C'est là que je me rends compte que vraiment pour une bouteille de plongée à charger ce que ça me coûte alors là je savais pas dans quel genre de Bidon d'huile faut-il que j'achète est-ce que vous avez une référence Parce que je suppose des que je vais la recevoir elle sera vide ski normal
👍🌹
No info about oil on the unit
Can you use antifreeze for cooling purposes
I would add antifreeze, 30 to 50%, to prevent corrosion to the aluminum that was shown in the video.
? quel genre de bouteille d'huile il faudrait pour Yonntech Pompe à air comprimé à haute pression, 300BAR 30MPA 4500PSI Fusil de système à contrôle automatique Compresseur
My instructions say to start the machine with both relief valves open. Has this changed???
it is not needed, you need to build up pressure, you only need to open it to let the air out and the moisture that has built up...
What type of oil does it use? Where is the oil fill?
I had the same problem hydraulic 46 fill from top where tag is with breather piece is he shows where to fill in video
@@Joeysav57 my manual says MOBIL 827/829 OR EQUIVALENT.
Equivalent!???
SECOLUBE 500 or equivalent. Dont use hydraulic oils; they're for heavy machinery sealed systems. Secolube is a breathing air compressor specific oil designed so it doesn't ignite on the second stage of compression. Its pricey, but it'll make your compressor last longer as well as making your high pressure guns last a lot longer since there's no toxic particles entering your gun
Mine just hums when I turn it on. Brand New today, and it doesn't work. Why wouldn't one of these things start.
Btw, the water pump doesn't work either. It hums to, but I think it needs to be primed, but how?
whatsyurprob ? my WhatsApp:+8618921610235
@@hengyong820 I don't understand why you gave me your #. I live in, America, and I don't believe I have the capability to call it with my current phone plan.
All I know is, this is a brand new matching, but it hums when I turn it on, and the fan now wants to turn but stops. I try to help move it along, but no dice.
Do both of the pressure valves have to be tight, or lose when I start this thing? I don't want to damage it.
@@whatsyurprob158 He is mentioning his number so you can add him in whatsapp. To use whatsapp you only need an internet connection on your smartphone
@@hengyong820 I'm having an issue with pump
Ce qui m'intéresse est de gonfler une carabine PCP sans paser par une bouteille "tampon". Une vidéo sur le sujet m'intéresserait.
Pour info, carabine stoeger PCP XM1 20 joules)
merci toutefois.
Exactement La même façon mais utiliser la «fill probe » pour la carbine. Je fais ça de temps en temps.
Why is the email address in the owner's manual for the compressor I just got invalid ???? How do I get hold of Yang Hang ?????
Jaaaaysus Christ. You break everything don't you.
@@joshuagibson2520
It's not broke it's brand new but I had some questions about it ! And the email address in the owner's manual for a brand new compressor the email address for Hang Hang is a invalid email address !
Its Europe's 220 it has the auto shut off the 110 doesn't from what I've learned. No less than five gallons of water
I just bought one of these compressors. The operation manual stinks. It doesn’t tell you how to use anything.
Hello, how can I contact you, to place an order?
Amazon.com
how to order
Olio ??? Aw46 ??????
Information ❌❌
Relaxation music ⭕⭕
Hello sir, the cooling on this compressors is not smart, there must be a second water inlet and outlet on the opposite side! Even when its cool from the front, the back gets very warm, so you have to use extremely cold water to hold this in tolerance. I made this second in and outlet by myself and bought a more powerful waterpump, now it can be used much longer and the piston rings don´t begin to melt, this happened a few times in the past because of inappropriate cooling method that was before, when the piston rings melt it gets stuck and the rocker ripped apart. But now i have another problem, the motor seems to have lost some of it´s power :( it shuts down a few times, before i get to 4500 psi
It would be nice if this stupid music wasn’t playing. I like to hear people talking step-by-step.
…this video is as close to useless as you can get!