1991 Sony WM-190 Walkman Repair (Japanese Import)

Sdílet
Vložit
  • čas přidán 25. 08. 2024

Komentáře • 28

  • @YouTube4Rudy
    @YouTube4Rudy Před 25 dny +1

    Okay this video scared the hell out of me. I won't be do this anytime soon. The older Walkmans seem a little easier. Anyway, new subscriber, I''ll be watching your other repairs videos, thank you.

  • @imperialanimation9267
    @imperialanimation9267 Před 8 měsíci +1

    Great Video, thank you. One of the best looking SONYs a nice blend of modern looks with mechanical buttons. Blimin good sounding too.

  • @TA3HGU
    @TA3HGU Před 6 měsíci +2

    Değerli arkadaşım güzel, detaylı bir onarım olmuş. Elinize sağlık. Ama müzik sesinde titreme var. Sanıyorum pink roller değişimi gerekiyor.

  • @LapisandHamtarolover
    @LapisandHamtarolover Před 4 měsíci

    I'm sure that the comparable EX39 is going to be longer lasting than these EX49 long term after 30 years.

  • @azpeitiajulian7039
    @azpeitiajulian7039 Před 3 měsíci +1

    Thank You very well explained greetings from CDMX could You help me with name of they band

  • @LapisandHamtarolover
    @LapisandHamtarolover Před 2 měsíci

    3:56 - actually that's the correct alignment side instead of upside down!

  • @deltic17
    @deltic17 Před rokem +3

    Bedtime viewing sorted 😊

  • @beebeenuts7267
    @beebeenuts7267 Před 4 měsíci +1

    my ex50 walkman(same internal mechanism as in the video) makes the same buzzing sound and i think its cause of the "corrosion" in the motor magnet like you said(sounds like the back of a fridge buzzing), is there a way to fix this or should i replace it? if so where can i get a replacement? at the end of the video the music was fine how did you fix it?

    • @jamesbennettmusic
      @jamesbennettmusic  Před 4 měsíci +1

      The buzzing noise is caused by the capacitors failing - the only fix is to replace them. The motor corrosion doesn't cause noise but it causes loss of torque and higher current drain from the battery

    • @beebeenuts7267
      @beebeenuts7267 Před 4 měsíci

      @@jamesbennettmusic do you know what type of capacitators should i get? and take note the buzzing of the motor happens even without the belts

    • @jamesbennettmusic
      @jamesbennettmusic  Před 4 měsíci +1

      @@beebeenuts7267 I did it with Panasonics from a UK trade supplier - you'd have to find SMD capacitors of the right value, voltage and size from a supplier in your country

  • @paulolivarri4552
    @paulolivarri4552 Před 5 měsíci +1

    Would the capacitors be the culprit of if I replaced belt and clutch gear and the sound sounds like the motor with hissing

    • @jamesbennettmusic
      @jamesbennettmusic  Před 5 měsíci

      Most likely yes! Some are used to decouple the preamp and Dolby stages, so if they fail, signal will not pass, and voltages will be off

    • @paulolivarri4552
      @paulolivarri4552 Před 5 měsíci

      @@jamesbennettmusic how hard and what capacitors would I need to change I was barely able to desolder and resolder the wires to flip the board

    • @jamesbennettmusic
      @jamesbennettmusic  Před 5 měsíci

      @@paulolivarri4552 all the SMD electrolytics like I did in the video - not easy

    • @paulolivarri4552
      @paulolivarri4552 Před 5 měsíci

      @@jamesbennettmusic do you happen to take orders for recapping

  • @arrowtransport3837
    @arrowtransport3837 Před 2 měsíci

    please WM-B603 restor link

  • @allardsylvain2773
    @allardsylvain2773 Před 2 měsíci

    Great video. Mine has bad sound like snoring. Why ? Capacitors ? if yes, where can I buy them? Thanks

    • @jamesbennettmusic
      @jamesbennettmusic  Před 2 měsíci +1

      Thanks. Could be! I bought mine from Farnell in the UK, but you might have to find a regional supplier more local to you

    • @allardsylvain2773
      @allardsylvain2773 Před 2 měsíci

      @@jamesbennettmusic thanks, can you provide me list need to be replace according to service manual?

    • @jamesbennettmusic
      @jamesbennettmusic  Před 2 měsíci

      @@allardsylvain2773 stereo2go.com/forums/threads/fixing-my-wm-ex49-capacitor-questions.6028/

    • @allardsylvain2773
      @allardsylvain2773 Před 2 měsíci

      @@jamesbennettmusic thanks a lot. Is there a position of the gears to be done before close with the board Electronic ?

  • @huntermoore9163
    @huntermoore9163 Před rokem

    do you have a list of the capacitor part numbers you used? i recently picked one up and am struggling to figure out what i need to repair it

    • @jamesbennettmusic
      @jamesbennettmusic  Před rokem

      Stock was surprisingly difficult to find and I ended up having to pay a premium to get them from Farnell. Drop me an email (should be able to find it on my CZcams profile) and I'll forward the numbers from the order I made!

    • @huntermoore9163
      @huntermoore9163 Před rokem

      @@jamesbennettmusic i am not able to find it on your profile

    • @jamesbennettmusic
      @jamesbennettmusic  Před rokem

      @@huntermoore9163 are you on a phone? It should have a section on the 'about' tab but might only work on computer

    • @huntermoore9163
      @huntermoore9163 Před rokem

      @@jamesbennettmusic okay sweet, it is only viewable on computer ill email you now