You need to watch this before installing a 30% gear reduction in your Can-am X3 Max.
Vložit
- čas přidán 6. 08. 2024
- Get the Torque Back!
Your Maverick X3 has a ton of power, but once you upgrade to those
tires it’ll feel like the torque is all gone. Upgrade your Can-Am Maverick X3 Transmission . You’ll get your power back and then some! Super ATV has 10%, 20%, or 30% gear reductions, so you can pick the perfect match for your setup.
If you’re running tires that are only a little bit bigger than stock, a 10% gear reduction is a perfect choice. But if the tires are way larger, you could need 20% or 30% reduction to get torque back to your expectations. Get your Can-Am Maverick X3’s power back..
@BikemanPerformance
@SuperATVMedia
#rockcrawler
#canammaverickx3
#adventure
#overlanding
#coosbay - Zábava
ive been waiting on a video been wanting to do this since they came out with it
So far I really love it, the only downside so far is the loss in top speed and a little fuel economy. A twenty % reduction probably would be the best all around, that being said it will crawl like no other 2mph Up about anything until the tires start slipping. Thanks for watching and supporting the channel.
Have you had any issues with the gear reduction since you installed?
None, it’s been fantastic. Currently abound 1800 miles on it so far. Over two hundred of those miles was pulling a 1500lb teardrop camp trailer. Transmission and clutches did awesome, axles not so much.. lol
can you link the video from the can am crew where they took apart the trans?
czcams.com/video/423y_6CfOF4/video.htmlsi=7yG0JDb82M6k1bsN
This is the link to the can am crew, tearing down the transmission. I hope this helps..
I have a 2023 2 seater I run 35s trail ridding and 32s hill climb racing in Tennessee and surrounding states I looking at doing a gear reduction do you think 30% would be to much or what would you recommend
I believe 30% is a little too much. 20% would probably be better for most. I do love how well the 30% rock crawls but you will sacrifice top speed 68-70 full shift out and running 8300 rpm’s. Thanks for commenting and supporting the channel..
Awsome thank you for the response you received a new subscriber love the videos so far!
Thank you
I have heard of guys putting weld on the gear to shaft after you press it on, do you feel that the press fit is good enough for big tires and big rocks?
i know a lot of satv stuff is cheap overseas junk, how you feel about putting them gears in your transmission? if they fail you will be completely dead in the water....
I have talked with a couple individuals putting the Sara. Gear reduction in that are going to tack weld them, just to be on the safe side. I was pretty confident in the press fit but time will tell. Thanks for watching and supporting the channel..
@@091200xr I'm wanting to do 20% in mine with 35s...this was a very good info and was not bashing satv or nothing just very curious as this looks like a good way to go..only other option is cryoheat and they use turner axles gears and they have to install them for you...definitely keep us posted and keep up the good content...
@@jameshigdon9286 Thanks and we definitely will..
Need help finding clutch kit 2022 x3 max ds
Contact Bikeman performance and let them know your riding style and any changes to the machine other than stock..
What clutch kit did you run?
@jasonmiddaugh8203 We installed a Bikeman stage 2 kit
Let me know if you need any help finding the right kit for your machine, I would be glad to assist.
Hello, the new single gear from the kit, does that get pressed into the "pinion drive shaft"?
You will have to press off the stock gear first the install the one from the kit.
Let me know if you need anything else, you can go to our Facebook page 208 Adventures and pm me with any questions. Thanks for watching and supporting our channel..