Bro fell down from heaven and gave us step by step instructions on how to save $15k. Thank you. I have a 3 group very similar just a bit older. Nova Evd2 model. I have nothing coming out of any of the 3 groups. Is there still a service kit available for these (gaskets/seals/rings..)? I'm in Canada.
Hi great video! I have Wega coffee machine with 2 groups model EVD but I think I have a problem with the pressure as the left side pours out more water and the right side pours out less water and more steam. The pressure thermometer stays at 3-4 when it is not in use and goes up to to maximum 6 when in use it does not touch the green zone at all. Do you know where the problem could be and how to fix it please?
if the pressure stat goes bad, and only two of the connection points are used already. Can the other points be used or does the whole thing have to be replaced?
Can use the other one no problem, pull the burnt one out w pliers so it doesn't affect the good terminal by not closing completely. Don't forget to subscribe
thanks for reply how much is your coffee and do you have amount i could buy to try out i live in townsville queensland just setting up shop and have a wega polaris 2 group i sorted power but have problem wont pragam left side grouyp any ideas what to fix cheers lee
@leighyarnall7346 check the switch on the right have side is on while programming and off while using. U will find the switch under the right steam knob
need expert advice on how to clean a hx boiler. There is a layer of SUPER hard black resedue I can't get rid off. I have Used decalz, and cafiza. No effect really. And now I am going to a surface specialist in blasting with glas.
@@coastcafeequipment I never used citric. I just used the normal coffee decalz. Maybe my solution was not strong enough. Anyway I am hoping the blasting will remove it, and make the copper surface stronger
Thanks for this video.
This video is lot of useful for me....
Great job bro...👍👍👍
This is probably one of the most useful videos on espresso machines that exists on CZcams
Thanks alot 🙏
Bro fell down from heaven and gave us step by step instructions on how to save $15k. Thank you. I have a 3 group very similar just a bit older. Nova Evd2 model. I have nothing coming out of any of the 3 groups. Is there still a service kit available for these (gaskets/seals/rings..)? I'm in Canada.
You should be able to find seals and parts for any wega.
❤
Hi great video! I have Wega coffee machine with 2 groups model EVD but I think I have a problem with the pressure as the left side pours out more water and the right side pours out less water and more steam. The pressure thermometer stays at 3-4 when it is not in use and goes up to to maximum 6 when in use it does not touch the green zone at all. Do you know where the problem could be and how to fix it please?
Clean the jets and filters to start, then clean the flow meters if the issue continues
if the pressure stat goes bad, and only two of the connection points are used already. Can the other points be used or does the whole thing have to be replaced?
Can use the other one no problem, pull the burnt one out w pliers so it doesn't affect the good terminal by not closing completely. Don't forget to subscribe
@@coastcafeequipment Thank you. And I will
I'm looking for used espresso machine! Can you suggest anywhere to look for please?
We sell used machines, are you in Australia?
@@coastcafeequipment i though you are in italy or europe .. yes im looking for used machine but inside europe or in dubai
hi great video i have a 3 phase group 2 wega polaris have you got info to re wire to single phase please
cheers leigh
I'm sorry I don't. However I don't think there is any 3 phase machine. Perhaps 32amp. You can change the element or limit the elements you use.
thanks for reply how much is your coffee and do you have amount i could buy to try out i live in townsville queensland just setting up shop and have a wega polaris 2 group i sorted power but have problem wont pragam left side grouyp any ideas what to fix
cheers lee
@leighyarnall7346 check the switch on the right have side is on while programming and off while using. U will find the switch under the right steam knob
Other issue could be the flow meters
, look at the video how to locate and clean.
You can order online @
spinaespresso.com.au/
need expert advice on how to clean a hx boiler. There is a layer of SUPER hard black resedue I can't get rid off. I have Used decalz, and cafiza. No effect really. And now I am going to a surface specialist in blasting with glas.
Acid
Usually people use acid
what kind of acid?
@plurplursen7172 critric from what I have heard, but I haven't done it, see no reason to. So do some research
@@coastcafeequipment I never used citric. I just used the normal coffee decalz. Maybe my solution was not strong enough. Anyway I am hoping the blasting will remove it, and make the copper surface stronger
I have single group, same model. Works good manually but automatic shots are not working, any ideas. Would it be the main board or the button board.
Could be, more info needed
What info do you need
@patricklucki5368 could me main board, buttons, ribbon cable, flow meter. Need a tech to look at it on site, it sounds like
My wega 3 group coffee machine is not turning on.there is no power. Can you pls assist where I can find the fuse location. I will try and change it
There is a fuse on the main board, unlikely to be the issue. Most common is main switch issue
Thank you
How can i set the wega Program setting for being auotamatic
Under the right steam handle is a silver switch , needs to be down