Well done for doing the right thing! That crossing is very dangerous and I do hope Network Rail have attended to it before something very serious happens. Thanks for filming it and I think you should send it on to Network Rail. Thanks, Ken
The solution is very simple, just use the phone on the crossing to ask what is going on. In any case these are full barriers so the signaller cannot release the railway signals until the barriers are down. Note that half-barriers or open crossings are not interlocked with the railway signals so you should definitely ring the railway signaller to tell him what is going on for those types of crossings.
There is usually a phone near to the level crossing gates which connects you directly to the signaller for that section of the railway, so the next time you come across this situation, have a look around for a yellow, white or grey rectangular box, and the signaller will take the appropriate action.
There's always a (yellow) phone at the crossing, which you should use to report any level crossing faults. It gets you straight through to the signalling centre. They'll be grateful for your call.
Not all crossings have a publicly accessible phone. A monitored crossing like this wouldn’t need a phone as the signaller would be watching it and would also have a failure indication on his/her workstation in events like this. Crossing phones are usually only found in locations where the crossing is automatic and un-monitored, as the signaller has no idea if something is obstructing the crossing. There will be a phone just inside the crossing boundary, to allow maintenance staff to take control of the barriers locally, but to reach it would technically be trespass for non-railway staff. As you done, best way in an emergency would be to call 999 as they can contact NR control and the BTP directly, and the local signalling fault team would be despatched. The Highway Code is quite clear though to all those nutters going across. You DO NOT PASS a flashing red light. That applies even if the barriers are up. It’s a quick route to a Dangerous Driving conviction. The chances of a train coming are almost nought, because with the barriers up, signals cannot show a green, but would you take the chance?
@@southcalder They still need a phone - so they should have one, not skimp on the cost of a phone. The Highway Code specifically says to use it to make sure it's safe to cross. The CCTV operator can't tall you if it's safe to cross. They can't tell you if they're holding the trains back. They can't tell you anything, because they're sat in a room monitoring CCTV. Relying on cops doesn't seem the best idea - I've seen them trying to deal with a level crossing issue before and they didn't have a clue about contacting the signaller. Of course if it's the only option, guess you gotta do that eh?
@percymerlin That is definitely so; I worked for BR on level crossings for 6 years. The ones where the danger lies are the AHBs - unmanned and automatic, they are not interlocked with the signals
Yes, there is clearly an issue with the barriers here. The action that you took was correct (the Police would have informed the railway) This appears to be an automated crossing. Should there have been a signalman in the box rather than a computer.......... I guess its all about saving money. A great video that makes a very good point; this could have been much worse. It just goes to show that railways (and roads) need that human touch.
Well done to the silver car for turning around. Safest decision. And for those saying look if the train is coming or not then cross. Here's something to think about, a train at 125mph would take about 8 seconds to cover 1/4 of a mile so by the time you look & return to your car & drive on it may be too late. Don't risk it. Wait or turn around!
125 mph? Many of the commenters are probably from a country that does not allow that. Here, or in my state at least it is like 80 max. for passenger and like 50 max. For freight and in the city they go like 30 max. In my city the only two lines that go through are not kept up cause they have little business on those ones. So they go like 10 mph. max. So here if a crossing is malfunctioning since they don't care about those ones, we use it as a stop sign, if no train you go. Also we don't set off the crossing and not actually cross for over ten minutes. If a train comes near they can turn them off and then back on again. So only a moron would sit that long with no train here. So there are good reasons why you would not wait here, and apparently good reasons why you would wait there or other countries. Oh, and another thing is our crossings are usually clear so you can see very far down the track without ever getting out of your car. Sometimes you can see 2 miles if it is flat enough.
The UK is very different. Often you could see a mile at best and many lines are 125mph here. As far as I know the only lines in America that reach (and exceed) that speed is the Acela Express
Ok after reading most of the posts on here clearly people don't know much about the workings of the railway, which isn't surprising because it gets very complicated, i work for network rail and trust me it does get complicated lol, anyway here is a bit of information for you all ,that is if your interested, looking at the vid the barriers did fail, phoning the police was the right thing to do however it was not needed as this was not in any way a dangerous situation, the only reason i can see to phone the police is because people were running the red lights ( they are classed above traffic lights not even emergency services are allowed to pass level crossing lights when they are flashing), anyway the reason this situation is not dangerous in any way is for a number of reasons, firstly this is a CCTV crossing so the signaller in the main signal centre can clearly see on his cameras that the barriers are still raised, so what he would have done would have been to call some people to fix it (i wont go into detail as its a complicated procedure), the second safeguard is something called interlocking, this means that with the barriers raised the signals protecting the crossing cannot be cleared, so a train cannot approach even if the interlocking fails it will still hold protecting signals at a danger aspect, so there was no chance what so ever of a train arriving with the barriers raised, another note to prove that, is that both trains in the end of the video come past within a minute of each other, this could mean that they both were waiting at their protecting signals, waiting for a clear aspect, now im not saying that if you see this happen just sit there and do nothing or just drive across ( you will be breaking the law passing the red flashing lights), i would advise a call to the police (maybe not 999 as it is not life threatening) and let them know what is going on, i would advise against contacting the signaller as he or she will have their hands full with calling the staff that need to know and getting repair teams to site, also the signaller will still be regulating trains in their section, the last thing they need is for someone to phone them letting them know that the crossing is broke, anyway sorry for the long post hope it gives an insight into a bit of the railway for you :) take care and all the best.
Correct me if I'm wrong but don't these level crossings have the feature that the red lights will immediately flash with the barriers remaining raised if there's a risk that a train may run over the crossing without authority?
Thanks for posting this as it highlights a huge gap in people's knowledge. Police Officers no longer have the authority to instruct people to pass a red light under any circumstances. Assuming the people at the station don't know may have been a better starting point. If there is a telephone at the crossing that is always the best point of contact.
I'm a train driver and can confirm that you can drive trains across the crossing while the barriers are up as long as the lights are flashing. Red means stop, if you think they are broken then there is a telephone right there at the crossing (yellow box with handset inside) and all this information is in the highway code (Rule 293 & 294) The fact that virtually no-one commenting here and certainly none of the drivers know the highway code is extremely worrying.
However, unlike most Hangmans, they were stuck for a considerably long time which has sometimes lead to trains travelling through with open barriers, which could lead to a collision as well
@@agent_605 that wouldn’t happen because you can’t clear the signals on the line unless the barriers are in the lowered position on a level crossing like this
I believe there was a mechanical problem with the barriers that is probably why the barriers on the level crossing weren’t going down they were stuck in the up position
Leaving that aside, I've spoken to someone I know in S&T on the railway and they say the barriers would have been interlocked with the signalling anyway so until the barriers went down all approach signals would have been red. No danger, just inconvenience all round...
This crossing has literally done the same thing again just a few days ago. Luckily it only stayed in that state for 2 minutes and the lights just went out
Just so you're aware, the trains would've been made aware that the barriers had not closed. Looking at the footage once the vehicles in front of you have moved, I noticed the red truck looks rather close to the crossing. Chances are the sensors have picked up that there is a vehicle possibly obstructing the crossing so they haven't closed on it. Both train drivers would've been made aware and either instructed to stop or pass the crossing at a VERY reduced speed. Once there is a clear space for a short period of time, the barriers begin to close until the blue car obstructs the crossing until it reverses and allows the barriers the space they need.
once I wated about 15 mins at a crossing the train finally came, I started crossing and about 20 sec later they closed, trapping me and 3 other cars on the line. it was so scary but thankfuly they stopped the trains
For a start. Why weren't the barriers down immediately? How do motorists know after 5 minutes that the traffic lights are not broken? The main problem is that when a train enters the appropriate section of track the lights are automatic. Years ago there would have been signalmen spaced along the route who were in control of their section, and also in control of the crossing gates. Now we have people in control who cannot see what is going on. Great technology isn't it??
This crossing is manual (seems so) and the crossing is monitored via CCTV so they can still see the crossing. Should a crossing of this type fail to close, the signals for the trains will be locked at red thus trains can't pass.
Just know that some but not all SIGNALS are located at a point where the signaller will lower the barrier when the train goes past it. Take Paignton for example, the signal at Hollocombe, which is somewhere close to a mile away from the crossing. When the train goes past that signal, the barriers start to be lowered, but there is another signal afetr the Hollocobe signal and it's before the crossing. If hllocombe is a singal yellow and the signal before the crossing is at danger, the barriers may be down for longer.
That’s dangerous you can’t turn around before the level crossing at Havant because they is gonna be a head on collision and also you cannot go through the level crossing because the red lights are flashing Percy
If a Train driver knows theres a level crossing faults the train slows down to 30 40mph whilst passing the faulty crossing then then pass information back to the rail network operator
This happened to me in Hull, 15 minutes the red lights as on with barrier up, rang the police, they said this was not an emergency stop wasting our time.
If you are in Australia with a similar situation, *DO NOT* call the emergency number (000) but call for police attendance (131 444). You will get a positive & timely response.
Why didn't someone just put the handbrake on, put their car in park, and phone the signaller from the phone box at the crossing? You know, like you're supposed to do?
There's a crossing like this in lydney, but there's a train station one side of the track, so if you're on the other side and the train if within 10 minutes of the station then you miss your train. Silly idea.
Would never go though a crossing with warning light like that myself irrespective of if the barriers were down or not, I'm paranoid. But that was a really long gap between the lights starring to flash and them coming down.
This was clearly a Level Crossing failure, the lights do not normally flash that long without barriers lowering on any barriered crossing. A yellow warning light of ten minutes is too excessive, as if you get to a crossing with a yellow light showing, you don't know how long its been there? And even then, whats to stop people thinking, "Oh its only yellow, the train will be ages away."
Police officers can no longer direct traffic over as a level crossing. The rule book states the signaler can advise the police officer of why the barrier isn't working and what action is being taken but they are not to be allowed to direct traffic over a crossing. Users should be told to wait or use an alternative route.
This happened yesterday at Cosham e.g. the gates were suspended half way. Perhaps they sense something passing under them and don't close until the object has cleared? If so I would hope it would send some kind of warning (let's call it a 1D10T code) to the signal operator. Luckily at Cosham most of the trains actually stop at the station so they would be travelling slow enough to react to any cars somehow caught on the crossing.
2:10 Well called. Calling the BTP (0800405040) or the signaller (using the crossing telephone) would have been ideal but if you didn't know the correct number to call then you can't really be criticised for using 999/112.
The cameras are wide angle and can see the whole crossing the signals will not allow trains to pass unless they are down they is a bit more to crossings than just some lamps on the top of a stick
There is what looks like a signal box on the other side of the railway line to you. Could it be that the bobbie was already aware there was a problem, had radioed control and got permission to wave some cars through as they knew a train wasn't due immediately? Also, may be worth checking the phone number either for BTP or for the loca police rather than bothering 999 with this sort of thing...
Train crossing, signals, and gates DO sometimes fail. What I don't understand is why some towns build so many fences, buildings, and other obstructions so close to train crossings that drivers can't possibly see if a train is coming until they're already on the tracks..
because trains come so quickly it doesn't matter AND that it's completely illegal to cross. Red means stop and the penalties for driving your car across the crossing while the lights are red can be, in extreme cases (i.e. collisions) years in jail.
As a Signalman, you did the right thing by phoning the police, but maybe did it too late. If ever a Level Crossing seems not to be operating correctly, either find a publicly accessible railway telephone or railway telephone number, or contact the police, who will have the necessary contacts to get the word out to the supervising signalbox eventually (if not directly, via Control).
Isn't that crossing actually controlled by the signal box right next door (the building on the right of the picture)? Just poke a head out of the window. As it's a CCTV crossing they would know the barriers were stuck open regardless of location, and there's interlocking so you can't set the signals for trains across the crossing to clear until it is confirmed closed. Black car was also an idiot for attempting to pull out and overtake on a solid white line.
After waiting several minutes (but less than ten) I would have assumed that the signals were malfunctioning and driven through. Not a safe thing to do, but these signals were "crying wolf". Events like this teach disrespect for safety devices.
you should check the highway code. If you think something is wrong you use the railway telephone situated at the crossing (yellow box) - rule 293 & 294
10 x traffic offences in this video. A typical case of a train being in the "section" which causes the red lights to flash. The barrier doesn't come down until the train passes an automatic switch, therefore giving the red lights chance to warn motorists. I suspect that the train was stopped by the signal man, who has no over-ride, or probably by animals/people on the track so it took longer to get to the crossing. Interesting. It's safer to wait.
I'm guessing either the crossing malfunctioned or the signaler activated the lights and alarm in error and did not realise it until a train was due ten minutes later. Probably the latter.
I used to live near a level crossing (Ash) where the wait was sometimes 30 minutes as the barrier was down whilst the train was in the station and stayed down until the next service arrived and several after that. I once passed a woman in a car on my motorcycle who said she had been waiting 40 minutes and was unlikely to get through within the hour. Level crossings are dangerous and the rules must never be broken but the Network Rail needs to sort out the lazy and incompetent people operating the barriers and issue what performance specifications they expect of their own staff.
The barriers should go down when a train approaches the platform because bad track conditions could cause the train to overrun the platform and run straight into traffic, but after the train has stopped at the platform, the barriers should go back up.
I don't want a war of words. here is a section of the Highway code section 297 If there are no lights, follow the procedure in Rule 295. Stop, look both ways and listen before you cross. If there is a railway telephone, always use it to contact the signal operator to make sure it is safe to cross. Inform the signal operator again when you are clear of the crossing. It clearly states IF there is a railway telephone, so it is not mandatory, and there is not one at this crossing.
@headphones222 They'll have the contact numbers on file for the BTP and the local rail companies, so they can find out what's going on and get the situation fixed a lot quicker than the average private citizen. That said, the phone box usually provided at level crossings to call the signalmaster is probably your best bet in situations like this. They can then try to directly control the crossing AND track signals, or even get in radio contact with trains to prevent a crash & get things moving
Well done for doing the right thing! That crossing is very dangerous and I do hope Network Rail have attended to it before something very serious happens. Thanks for filming it and I think you should send it on to Network Rail. Thanks, Ken
great to see at least one person out there sticks to the law and stays safe
The fact that they waited over 10 minutes amazes me. In America you'd be lucky if the person waited 15 seconds.
Here in my Country, if you got no rush, you might aswell build a tent there.
Idaho where are you from?
The solution is very simple, just use the phone on the crossing to ask what is going on.
In any case these are full barriers so the signaller cannot release the railway signals until the barriers are down. Note that half-barriers or open crossings are not interlocked with the railway signals so you should definitely ring the railway signaller to tell him what is going on for those types of crossings.
There is usually a phone near to the level crossing gates which connects you directly to the signaller for that section of the railway, so the next time you come across this situation, have a look around for a yellow, white or grey rectangular box, and the signaller will take the appropriate action.
The Crossing Controller had an obsession with flashing 📸 lights
Never had this problem with gates turned by a wheel.
Could not agree more, interlocked gates are more reliable
Lifting barriers are more efficient, however
Several years ago in the Netherlands, a lack of patience at a railway crossing cost a woman and her small child their lives...
There's always a (yellow) phone at the crossing, which you should use to report any level crossing faults. It gets you straight through to the signalling centre. They'll be grateful for your call.
This is a CCTV Crossing and I've been to this location before. I do believe there are no phones present on this particular Level Crossing.
Sometimes the phone is in a white or grey box as well. Flagging the CCTV system can be useful in getting the signaller's attention as well.
All level crossings have a phone, usually about 100 yards before. As when we are pulling loads over 25m long, we need to call for permission to cross.
Not all crossings have a publicly accessible phone. A monitored crossing like this wouldn’t need a phone as the signaller would be watching it and would also have a failure indication on his/her workstation in events like this. Crossing phones are usually only found in locations where the crossing is automatic and un-monitored, as the signaller has no idea if something is obstructing the crossing. There will be a phone just inside the crossing boundary, to allow maintenance staff to take control of the barriers locally, but to reach it would technically be trespass for non-railway staff. As you done, best way in an emergency would be to call 999 as they can contact NR control and the BTP directly, and the local signalling fault team would be despatched.
The Highway Code is quite clear though to all those nutters going across. You DO NOT PASS a flashing red light. That applies even if the barriers are up. It’s a quick route to a Dangerous Driving conviction. The chances of a train coming are almost nought, because with the barriers up, signals cannot show a green, but would you take the chance?
@@southcalder They still need a phone - so they should have one, not skimp on the cost of a phone. The Highway Code specifically says to use it to make sure it's safe to cross. The CCTV operator can't tall you if it's safe to cross. They can't tell you if they're holding the trains back. They can't tell you anything, because they're sat in a room monitoring CCTV. Relying on cops doesn't seem the best idea - I've seen them trying to deal with a level crossing issue before and they didn't have a clue about contacting the signaller. Of course if it's the only option, guess you gotta do that eh?
It doesn't matter how long you wait, you cannot get your life back when your gone!
Look how some of the drivers got confused when the barriers didn’t come down and then decided to go through oblivious to the danger they are in
@percymerlin That is definitely so; I worked for BR on level crossings for 6 years. The ones where the danger lies are the AHBs - unmanned and automatic, they are not interlocked with the signals
Yes, there is clearly an issue with the barriers here. The action that you took was correct (the Police would have informed the railway) This appears to be an automated crossing. Should there have been a signalman in the box rather than a computer.......... I guess its all about saving money. A great video that makes a very good point; this could have been much worse. It just goes to show that railways (and roads) need that human touch.
It’s not automated as quad-barrier crossings are always controlled by a signalman
wow im glad you did something about it. that was an accident waiting to happen good job for thinking of others instead of yourself..
Well done to the silver car for turning around. Safest decision. And for those saying look if the train is coming or not then cross. Here's something to think about, a train at 125mph would take about 8 seconds to cover 1/4 of a mile so by the time you look & return to your car & drive on it may be too late. Don't risk it. Wait or turn around!
125 mph? Many of the commenters are probably from a country that does not allow that. Here, or in my state at least it is like 80 max. for passenger and like 50 max. For freight and in the city they go like 30 max. In my city the only two lines that go through are not kept up cause they have little business on those ones. So they go like 10 mph. max. So here if a crossing is malfunctioning since they don't care about those ones, we use it as a stop sign, if no train you go. Also we don't set off the crossing and not actually cross for over ten minutes. If a train comes near they can turn them off and then back on again. So only a moron would sit that long with no train here. So there are good reasons why you would not wait here, and apparently good reasons why you would wait there or other countries. Oh, and another thing is our crossings are usually clear so you can see very far down the track without ever getting out of your car. Sometimes you can see 2 miles if it is flat enough.
Old comment I know - but it's not 4 seconds, more like 8. To travel 1/4 mile in 4 seconds you would have to be doing 225mph
The UK is very different. Often you could see a mile at best and many lines are 125mph here. As far as I know the only lines in America that reach (and exceed) that speed is the Acela Express
Idiotic fail on 4th grade arithmetic !
are Trains allowed to go 125 on tracks where there are Level crossings? Or is it more like 25?
Ok after reading most of the posts on here clearly people don't know much about the workings of the railway, which isn't surprising because it gets very complicated, i work for network rail and trust me it does get complicated lol, anyway here is a bit of information for you all ,that is if your interested, looking at the vid the barriers did fail, phoning the police was the right thing to do however it was not needed as this was not in any way a dangerous situation, the only reason i can see to phone the police is because people were running the red lights ( they are classed above traffic lights not even emergency services are allowed to pass level crossing lights when they are flashing), anyway the reason this situation is not dangerous in any way is for a number of reasons, firstly this is a CCTV crossing so the signaller in the main signal centre can clearly see on his cameras that the barriers are still raised, so what he would have done would have been to call some people to fix it (i wont go into detail as its a complicated procedure), the second safeguard is something called interlocking, this means that with the barriers raised the signals protecting the crossing cannot be cleared, so a train cannot approach even if the interlocking fails it will still hold protecting signals at a danger aspect, so there was no chance what so ever of a train arriving with the barriers raised, another note to prove that, is that both trains in the end of the video come past within a minute of each other, this could mean that they both were waiting at their protecting signals, waiting for a clear aspect, now im not saying that if you see this happen just sit there and do nothing or just drive across ( you will be breaking the law passing the red flashing lights), i would advise a call to the police (maybe not 999 as it is not life threatening) and let them know what is going on, i would advise against contacting the signaller as he or she will have their hands full with calling the staff that need to know and getting repair teams to site, also the signaller will still be regulating trains in their section, the last thing they need is for someone to phone them letting them know that the crossing is broke, anyway sorry for the long post hope it gives an insight into a bit of the railway for you :) take care and all the best.
BlackriderUK if rail companies invest in up to date technology well things might be different
Correct me if I'm wrong but don't these level crossings have the feature that the red lights will immediately flash with the barriers remaining raised if there's a risk that a train may run over the crossing without authority?
I take it you don't need English writing qualifications to work for Network Rail or whatever they call themselves these days?
Train do sometimes pass over CCTV crossings with the barriers raised. It's rare but it does happen
Thanks for posting this as it highlights a huge gap in people's knowledge.
Police Officers no longer have the authority to instruct people to pass a red light under any circumstances. Assuming the people at the station don't know may have been a better starting point.
If there is a telephone at the crossing that is always the best point of contact.
I'm a train driver and can confirm that you can drive trains across the crossing while the barriers are up as long as the lights are flashing. Red means stop, if you think they are broken then there is a telephone right there at the crossing (yellow box with handset inside) and all this information is in the highway code (Rule 293 & 294)
The fact that virtually no-one commenting here and certainly none of the drivers know the highway code is extremely worrying.
That's 5 minutes I'll never get back
Sutton junction had the same issues 5/6 years ago.
*The barriers got stuck*
Its called a Hangman. Its where somthing or someone is in the barriers path
However, unlike most Hangmans, they were stuck for a considerably long time which has sometimes lead to trains travelling through with open barriers, which could lead to a collision as well
Some ppl might not have not kown what hangman was
@@agent_605 that wouldn’t happen because you can’t clear the signals on the line unless the barriers are in the lowered position on a level crossing like this
That's what the big (normally yellow) phone is for by the crossing, will connect you directly to the signaller
I guess they Havant a clue what went wrong there?
See what you did there!
I must praise you for doing what you thought was right. It makes a change to see someone with a brain use it!
We never have to wait more than 4 minutes on our local crosing... 10 & half minutes is too long, no wonder drivers got impatient.!
I believe there was a mechanical problem with the barriers that is probably why the barriers on the level crossing weren’t going down they were stuck in the up position
thank you to the driver who reported the problem.
Leaving that aside, I've spoken to someone I know in S&T on the railway and they say the barriers would have been interlocked with the signalling anyway so until the barriers went down all approach signals would have been red.
No danger, just inconvenience all round...
This crossing has literally done the same thing again just a few days ago. Luckily it only stayed in that state for 2 minutes and the lights just went out
Just so you're aware, the trains would've been made aware that the barriers had not closed. Looking at the footage once the vehicles in front of you have moved, I noticed the red truck looks rather close to the crossing. Chances are the sensors have picked up that there is a vehicle possibly obstructing the crossing so they haven't closed on it. Both train drivers would've been made aware and either instructed to stop or pass the crossing at a VERY reduced speed. Once there is a clear space for a short period of time, the barriers begin to close until the blue car obstructs the crossing until it reverses and allows the barriers the space they need.
that sounds very informative,but im afraid you aint got a clue what ur talkin about.
Lol. That's how the unmanned signals work by me... what's the correct info then?
What if barrier / lights is treadle operated so not protected by signal how do you stop the train ie hixon railway disaster no way of stopping train
Sounds about right people too impatient with their own journey. No wonder trains are late. But that's how it goes isn't it.
once I wated about 15 mins at a crossing the train finally came, I started crossing and about 20 sec later they closed, trapping me and 3 other cars on the line. it was so scary but thankfuly they stopped the trains
Here it is illegal to cross the tracks when the red light is flashing even if the train has stopped way down the track.
Well done with that phonecall! 👏🏻
For a start. Why weren't the barriers down immediately? How do motorists know after 5 minutes that the traffic lights are not broken? The main problem is that when a train enters
the appropriate section of track the lights are automatic. Years ago there would have been signalmen spaced along the route who were in control of their section, and
also in control of the crossing gates. Now we have people in control who cannot see what is going on. Great technology isn't it??
We have safety, unlock the US.
Unlike*
This crossing is manual (seems so) and the crossing is monitored via CCTV so they can still see the crossing. Should a crossing of this type fail to close, the signals for the trains will be locked at red thus trains can't pass.
The one crossing I railfan in Edmonton AB has a short activating distance so trains have to stop and wait for it to go down
Maybe it's a locally monitored crossing? Or maybe the driver needs to activate him/herself?
Cold beer just up the street
"I like trains..."
Commendable. That's called being obedient to a faulty.
The music at the start of this makes me lol
It came from the theme tune of an old UK TV series call "bird of prey"..
It kind of reminds me of Escape from New York music
Transformers 1985
Just know that some but not all SIGNALS are located at a point where the signaller will lower the barrier when the train goes past it. Take Paignton for example, the signal at Hollocombe, which is somewhere close to a mile away from the crossing. When the train goes past that signal, the barriers start to be lowered, but there is another signal afetr the Hollocobe signal and it's before the crossing. If hllocombe is a singal yellow and the signal before the crossing is at danger, the barriers may be down for longer.
People also will look both ways after a train has passed on a single set of tracks. LOL!
If they get stuckhalfway up, that's a Hangman.
That’s dangerous you can’t turn around before the level crossing at Havant because they is gonna be a head on collision and also you cannot go through the level crossing because the red lights are flashing Percy
0:27 crossing acts up
2:35 barriers play hangman
If a Train driver knows theres a level crossing faults the train slows down to 30 40mph whilst passing the faulty crossing then then pass information back to the rail network operator
This happened to me in Hull, 15 minutes the red lights as on with barrier up, rang the police, they said this was not an emergency stop wasting our time.
If you are in Australia with a similar situation, *DO NOT* call the emergency number (000) but call for police attendance (131 444). You will get a positive & timely response.
Why didn't someone just put the handbrake on, put their car in park, and phone the signaller from the phone box at the crossing? You know, like you're supposed to do?
kudos for actually knowing the highway code. no one in this video did.
@@xaiano794 Ta :)
There's a crossing like this in lydney, but there's a train station one side of the track, so if you're on the other side and the train if within 10 minutes of the station then you miss your train. Silly idea.
Probably shunting happening. Happens all the time in the San Fernando Valley. If the barrier is up, we just go.
Doesn't happen on the main line.
Look how close that Ford Focus came from getting hit by the silver Vauxhall Percy
_patience is a virtue_
Hello, how did you record this film? From TV? Because it looks like that. cu Toni
You had ONE job signal, ONE job, and you cocked it all up! You're FIRED! :D
Normie
Normie
3:42 ahhh British rail ... on time as usual :P
Er, British Rail ceased to exist from about 1996....
The words "busy bodies" come to mind
most likely. I have those moments, but not with the Eastenders theme
I can see the driver of the truck and the car both going through on red
seems fairly brief to me
Would never go though a crossing with warning light like that myself irrespective of if the barriers were down or not, I'm paranoid. But that was a really long gap between the lights starring to flash and them coming down.
I have sat at warblington gates for 20 minutes and not one train came thru, then the barriers lifted. must have been a ghost train !!!
IT just shows how impatient people have become and don’t give dam . About there life’s or others
Rise up sheeple! Throw off the bondage of your evil level crossing oppressors!
I never seen a problem like this before
Well why did the barriers come down about 3 weeks later?
they called
THE POLICE
GOOD IDEA
Thanks for sharing your boredom with us.
lee g lol
This was clearly a Level Crossing failure, the lights do not normally flash that long without barriers lowering on any barriered crossing. A yellow warning light of ten minutes is too excessive, as if you get to a crossing with a yellow light showing, you don't know how long its been there? And even then, whats to stop people thinking, "Oh its only yellow, the train will be ages away."
I feel like an idiot for watching this ! How bored can I be....
And THEN to comment! Time to go for a walk.
3 year later, enjoy that walk?
@@TCCcompetition - preety sure it was more interesting thanwhateer this video was. Thanks for asking.
Police officers can no longer direct traffic over as a level crossing. The rule book states the signaler can advise the police officer of why the barrier isn't working and what action is being taken but they are not to be allowed to direct traffic over a crossing. Users should be told to wait or use an alternative route.
This happened yesterday at Cosham e.g. the gates were suspended half way. Perhaps they sense something passing under them and don't close until the object has cleared? If so I would hope it would send some kind of warning (let's call it a 1D10T code) to the signal operator.
Luckily at Cosham most of the trains actually stop at the station so they would be travelling slow enough to react to any cars somehow caught on the crossing.
2:10 Well called. Calling the BTP (0800405040) or the signaller (using the crossing telephone) would have been ideal but if you didn't know the correct number to call then you can't really be criticised for using 999/112.
The cameras are wide angle and can see the whole crossing the signals will not allow trains to pass unless they are down they is a bit more to crossings than just some lamps on the top of a stick
What would cause the barriers to hangman? I hope that the crossing has been fixed now.
There is what looks like a signal box on the other side of the railway line to you. Could it be that the bobbie was already aware there was a problem, had radioed control and got permission to wave some cars through as they knew a train wasn't due immediately?
Also, may be worth checking the phone number either for BTP or for the loca police rather than bothering 999 with this sort of thing...
I think those cars were too close to the barriers so the barriers wouldn't go down because there's some in the way
Barriers don't care, they just go down.
10 minutes for the lights to be flashing seems a long time especially with the slow train speed .
Train crossing, signals, and gates DO sometimes fail. What I don't understand is why some towns build so many fences, buildings, and other obstructions so close to train crossings that drivers can't possibly see if a train is coming until they're already on the tracks..
because trains come so quickly it doesn't matter AND that it's completely illegal to cross. Red means stop and the penalties for driving your car across the crossing while the lights are red can be, in extreme cases (i.e. collisions) years in jail.
@@xaiano794 he means If there was to be a Failure with the crossing
the train wouldn't even come over the crossing as the train protection system would stop it at a red signal
As a Signalman, you did the right thing by phoning the police, but maybe did it too late. If ever a Level Crossing seems not to be operating correctly, either find a publicly accessible railway telephone or railway telephone number, or contact the police, who will have the necessary contacts to get the word out to the supervising signalbox eventually (if not directly, via Control).
They need to fix those crossings!
WOW, I'm glad I watched that, it was really exciting
Don't worry, at least I understood your sarcasm!
I've seen that car infront of you before...
Isn't that crossing actually controlled by the signal box right next door (the building on the right of the picture)? Just poke a head out of the window.
As it's a CCTV crossing they would know the barriers were stuck open regardless of location, and there's interlocking so you can't set the signals for trains across the crossing to clear until it is confirmed closed.
Black car was also an idiot for attempting to pull out and overtake on a solid white line.
In the US we might wait 2 minutes at best. If it's clear, we go anyway- even if the barriers are down.
Why did it take so long for the barriers to come down. No wonder people take chances.
British engineering. Same reason Landrovers are an electrical nightmare.
Chris P
If it was only the electrical system on a Land Rover that is a nightmare...
After waiting several minutes (but less than ten) I would have assumed that the signals were malfunctioning and driven through. Not a safe thing to do, but these signals were "crying wolf". Events like this teach disrespect for safety devices.
The barriers should have went down and lights flashing about 5 minutes before the train came, theres a problem with that crossing
Stupid wait for the over 10 minutes .......crazy gate stopping
the English like queuing and waiting and doing as they are told.
There are even some Railroad crossing signals without barriers.
your damn right.
I don't think that I'd wait so long. But i'd simply turn around and look for an alternative path. Hope there is one.
you should check the highway code. If you think something is wrong you use the railway telephone situated at the crossing (yellow box) - rule 293 & 294
Unrelated but nice pfp
Havant? Ha i live near there.
10 x traffic offences in this video. A typical case of a train being in the "section" which causes the red lights to flash. The barrier doesn't come down until the train passes an automatic switch, therefore giving the red lights chance to warn motorists. I suspect that the train was stopped by the signal man, who has no over-ride, or probably by animals/people on the track so it took longer to get to the crossing. Interesting. It's safer to wait.
I'm guessing either the crossing malfunctioned or the signaler activated the lights and alarm in error and did not realise it until a train was due ten minutes later. Probably the latter.
the problem is you can't tell unless you call him and trains are able to run across crossings with the barriers up as long as the lights are red.
To be fair it was flashing for 10 minuets.... so that train wasn't coming any time soon.
I used to live near a level crossing (Ash) where the wait was sometimes 30 minutes as the barrier was down whilst the train was in the station and stayed down until the next service arrived and several after that. I once passed a woman in a car on my motorcycle who said she had been waiting 40 minutes and was unlikely to get through within the hour. Level crossings are dangerous and the rules must never be broken but the Network Rail needs to sort out the lazy and incompetent people operating the barriers and issue what performance specifications they expect of their own staff.
The barriers should go down when a train approaches the platform because bad track conditions could cause the train to overrun the platform and run straight into traffic, but after the train has stopped at the platform, the barriers should go back up.
I don't want a war of words. here is a section of the Highway code section 297
If there are no lights, follow the procedure in Rule 295. Stop, look both ways and listen before you cross. If there is a railway telephone, always use it to contact the signal operator to make sure it is safe to cross. Inform the signal operator again when you are clear of the crossing.
It clearly states IF there is a railway telephone, so it is not mandatory, and there is not one at this crossing.
@headphones222 They'll have the contact numbers on file for the BTP and the local rail companies, so they can find out what's going on and get the situation fixed a lot quicker than the average private citizen.
That said, the phone box usually provided at level crossings to call the signalmaster is probably your best bet in situations like this. They can then try to directly control the crossing AND track signals, or even get in radio contact with trains to prevent a crash & get things moving
well done x
That crossing does it all the time
That's why crossings have a telephone so you can find out if it's safe to cross
The barriers most likely got stuck. The cars can look left and right but it is still dangerous. :/
Wrong. Red means stop.
+Xaiano wrong, If a crossing is broken, they may cross with permission
+East Sussex Level crossings and supercars with permission, yes, otherwise red means stop
+East Sussex Level crossings and supercars permission is only ever given when the line is clear