Good morning, Thank you very much for your answer it will allow me to be able to buy this position. with your info I know that I can use it in my garage my electric installation will suffice for the power. All my power sources are equipped in 2.5mm2 with 20A circuit breakers. In addition I will take this one but knowing that I will use it that 50% of its capacity. You have a nice machine congratulations for work. Michel@@garage-MOlo
Good morning I would like to buy it can you tell me what tension did you take I want to buy a 220V but I'm afraid I don't have enough tension at home I have a maximum voltage of 40a is this quite sufficient Thank you for all your info
Hey, how is Herocut - did You have any problems with it? On last film I saw You still have it and by tear on torch cable I assume it worked more than few hours, right?😀 I'm thinking of 230V HC7000 +hand torch because it is priced
Hello that cut looks amazing, i am using a cheap non pilot hf plasma and its killing my board. Do you have any interference issues with this plasma ? I am considering buing one asap. Thanks in advance
hello again sir, i got one and its pretty good. i only have 2 problems and i cant find a solution. what distance do you use from the nozzle to the metal ??? and what kerf width did you use in the software?@@garage-MOlo
Hi. I just purchased HC8000 cutter. Does the cooling fan starts to spin when you turn on the device or it spins only if needed? You made a nice CNC and I hope it serves you well 💪
Nice job on the machine. im trying to build my own cnc also using myplasm..it looks a great software.
take myplasm is a very intuitive, simple software. I recommend
@@garage-MOlo thanks
Przydały by się jakieś zgarniacze przed łożyskami, konstrukcja super!
Masz racje;) przydały by sie jakies szczotki
EN 220v Thank you for your answer another question
Remember which wire section (mm2) and fuse amprerage?
And thank you for your answers
2,5mm2 oraz 16A
Good morning,
Thank you very much for your answer it will allow me to be able to buy this position.
with your info I know that I can use it in my garage my electric installation will suffice for the power.
All my power sources are equipped in 2.5mm2 with 20A circuit breakers.
In addition I will take this one but knowing that I will use it that 50% of its capacity.
You have a nice machine congratulations for work.
Michel@@garage-MOlo
Good morning
I would like to buy it can you tell me what tension did you take
I want to buy a 220V but I'm afraid I don't have enough tension at home
I have a maximum voltage of 40a
is this quite sufficient
Thank you for all your info
Mialem 230V. Zmienilem na 400. 230 potrzebuje bardzo duzych przekrój przewodow i duzych bezpiecznikow.
Thank you for your answer another question
Remember which wire section (mm2) and fuse amprerage?
And thank you for your answers.@@garage-MOlo
Hey, how is Herocut - did You have any problems with it? On last film I saw You still have it and by tear on torch cable I assume it worked more than few hours, right?😀 I'm thinking of 230V HC7000 +hand torch because it is priced
I didn't have any problems. I recommend 400V. such a current from one phase. you will need to have a strong installation
To use it on the CNC, did you need to make any adaptations to this plasma source? Hi, the way you bought it, you can use it just by making calls.
is ready to use after purchase. The plasma has connectors for voltage measurement, plasma start and plasma supply
Hello that cut looks amazing, i am using a cheap non pilot hf plasma and its killing my board. Do you have any interference issues with this plasma ? I am considering buing one asap. Thanks in advance
I have no problems. cuts very well.
hello again sir, i got one and its pretty good. i only have 2 problems and i cant find a solution. what distance do you use from the nozzle to the metal ??? and what kerf width did you use in the software?@@garage-MOlo
Czy os Z jest z regulacją wysokosci podczas cięcia ?
Tak. Za to odpowiada sterownik thc
Приветствую !!! Я так понял с пневмоподжигом? Как она стоит брать?
Какой метал по толщине берет без проблем?
Yes
20mm
Пневмоподжиг ?
Tak
Hi. I just purchased HC8000 cutter. Does the cooling fan starts to spin when you turn on the device or it spins only if needed? You made a nice CNC and I hope it serves you well 💪
Wentylator kreci sie w razie potrzeby. Ale u mnie po 1 minucie ciecia sie włącza. Po skończonym cięciu jest załączony okolo 3-5 minut
@@garage-MOlo ok, thank for the answer
@@garage-MOlo thank you