Video není dostupné.
Omlouváme se.
DIY| How to remove your Motorcycle Rear Wheel| Kawasaki Vulcan 900 Classic| IT'S EASY!!!
Vložit
- čas přidán 8. 07. 2021
- I recently purchased a new rear tire for my bike. After that 10,000 mile mark the old back tire was worn. So, I decided to do a quick tutorial. The rule applies to most belt and chain driven bikes, the shaft drive will be slightly different. Changing your own tires will save you a lot on labor cost through shops. It only takes courage and confidences. Thanks for watching!!
Camera #1: www.amazon.com...
Camera #2: gopro.com/en/u...
Case #1: www.amazon.com...
Case #2: www.amazon.com...
Accessories: www.amazon.com...
Chin strap: www.amazon.com...
Mic adaptor: www.amazon.com...
Mic: www.amazon.com...
Helmets:
www.amazon.com...
www.amazon.com...
Jackets
www.amazon.com...
www.amazon.com...
www.amazon.com...
Gloves
www.amazon.com...
www.amazon.com...
Saddlebags
www.vikingbags...
Great tutorial! I like that you showed the tools used, the parts, etc. Very thorough.
Thank you!! Thanks for watching!! Just trying to make it easy for some!!😁👍🏿
Good video. Very very easy once the exhaust is removed.
Thanks Sean!!💯 You right, very very easy. I see people take their bikes to shops for tire changes, which is fine. But it is a simple do it yourself job.👍🏿
Thank you
You're welcome!!! Thank you for watching!!👍🏿💯
Great video, I love the way you took the time to show each part as you removed and reassembled it. How much would you charge to do my Suzuki????🥴😁😅
Thanks H!!👍🏿 Maaaan, I've never done a shaft drive, but hey we can do it together!!!🤣🤣😅
@@TD205 I'm going to hold you to that 😁😅
@@heheatingandairllc.3223😁👌🏿
Thanks for the video
Your welcome!! Thank you for watching!!!
I need 2006 Vulcan Kawasaki tires remove
The process is the same for removing the wheel. I had a 2008. I take the wheel to Cycle Gear and have them remove the tire👍🏿👍🏿.
I need a tutorial on how you had it jacked up on them stands 😂looked pretty stable.
It was too easy. I had to jack rested on the rear frame😅👍🏿👍🏿. Thanks for watching!!💯
@TD205 thanks for showing I got hit on mine back in October imma about to get it back up and going I got replace that rear brake bracket and aligned the belt so your video came In handy & now imma save my money & not buy a jack 😁😂👍🏿💪🏿
@@slimthezzy2180 Sorry to hear you got hit😔. I'm glad my video could assist💪🏿. Y'all be back in no time💯. Stay safe!!
Ah hm, never saw the pipes come out? or the belt and video took too long so cant watch and not complete, therefore not useful at all? There is a lot more to it then what you are showing here bro.
Thanks for watching! The job was completed for me. Old tire removed, new tire installed. The video has helped several others. If I can help 1 person, I'm cool with it. There was no need to show me removing my pipes. The belt all you do is carry it over the pulley which is simple. If you have a video I'll watch it.
Great vid. How did you set up the bike to lift it and set up the jack stands?
I actually put the floor jack on the lower center rear frame. Jacked it up and use the jack stands for extra support. Thanks for watching!!!👍🏿
@@TD205 thank you again do I have to take the exhaust off?
@@cptpapa No problem. I believe so, at least I did. You have to get your axle bolts completely out.👌🏿
@@TD205 so what part of the underside did you place the floor jack? I am having a rough go at it and can’t get the bike to balance. Also how do you have the front tire set up? Thank you!
@@cptpapa Put your jack stand in the center of the bikes frame. Right in front of the rear tire. Lean the bike straight up. Then pump your jack up. The front tire should be stable once bike is off the ground. If not put 2 cinder blocks, 2x4 or something on each side of the front tire. Rear end of the bike should lift straight up.
Use a mallet,not a hammer! Or a little peace of wood between. You'll be glad you didn't screw up the threads!
Thanks for watching!!
waste of time watching this video
Thanks for watching!!
Never trust a man with a hammer like that 😂
Thanks for watching!!