The gripper has two screws, unscrew, sewing to the lowest position. When the seamstress starts on the mountains, you turn the grapple tip towards the sewing machine. Grab the grapple! Practice makes perfect.
postovani trenutno posjedujem Pfaff 335 masinu,nadam se da mi mozete pomoci,timing je ispravan (koliko su mi rekli) medutim kada krenem sivati,donji konac uopce ne ide te ga gornji ne hvata,neki savjet bih vas molio hvala vam
Hello, any chances of giving me a hand please? My Pfaff 335 clone has got 2 problems: the manual foot lift does not work and the walking foot does not make contact with the plate so the presser foot stays in the same point all the time and doesn’t not stitch anything. I have got videos that show the problem. Please help if you can, thank you
can we increase the stitching space to 5mm , I have this machine but the stitching maximum is 4mm , can you make a video if that's possible improvement , also I am planning to use S10 thread thickness which is this thread but fits needle 140 / 22
Hello Mivel50,, are you replacing the original hook and bobbin with a larger m size bobbin? I have a 335-h3 that I would like to use 138 thread on it and equivalent to side 22/23 needle like I use on my Juki lu563 … is this possible
Hello! Thanks for the video. At 2:41, how did you move the tip of hook away from the needle to give spacing (0.05 - 01.mm)? Thank you!
The gripper has two screws, unscrew, sewing to the lowest position. When the seamstress starts on the mountains, you turn the grapple tip towards the sewing machine. Grab the grapple!
Practice makes perfect.
🍀majstore odlicno..muzika odlicno..snimljeno..odlicno
Hvala kolega, služim narodu. Pozdrav
👍
Pozdrav majstore.Da li se moze povecati step na pfaff 335 h2,na recimo 7 ili 8 mm..
postovani
trenutno posjedujem Pfaff 335 masinu,nadam se da mi mozete pomoci,timing je ispravan (koliko su mi rekli) medutim kada krenem sivati,donji konac uopce ne ide te ga gornji ne hvata,neki savjet bih vas molio
hvala vam
Are these bigger spuls than standard Pfaff?
No, most are responsible for one and the other, each machine has a catalog, it can be looked at
Desmontou quase tudo pra colocar a lançadeira
thank you
Donde puedo conseguir los repuestos de esa maquina x ejemplo esa lanzaderas
Si en su pais hay una agecia pfaff hay lo puedes comprar
Hi, instead of your own screwdriver, use a wrench with a mechanism and a nozzle, such are the kits for cars
Thanks for the advice, hello
Hello, any chances of giving me a hand please? My Pfaff 335 clone has got 2 problems: the manual foot lift does not work and the walking foot does not make contact with the plate so the presser foot stays in the same point all the time and doesn’t not stitch anything. I have got videos that show the problem. Please help if you can, thank you
Send the video to the e-mail: cevljar@atlas.cz
I'll take a look
Hello
thanks a lot, you're a good teacher
Thank you colleague, I serve the people, greetings
Rosszul van a tolás beállítva, ugrál az anyag előre-hátra...
can we increase the stitching space to 5mm , I have this machine but the stitching maximum is 4mm , can you make a video if that's possible improvement , also I am planning to use S10 thread thickness which is this thread but fits needle 140 / 22
Which type: H1, H2, H3, H4 ....
Mivel50 h3
Thread keeps breaking although I followed. Your steps exactly , sane thread was ok before , nylon bonded
@@azzamody Pfaff 335 is not for sewing thick materials. Has Needle system seams: 134-35 LR
Needle size: 80 - 100 Nm
Mivel50 it did sew 5mm leather with thread 20s which is 138 ... but then when I replace needle to 140-22 I faced issues
Ceme timming
Hello Mivel50,, are you replacing the original hook and bobbin with a larger m size bobbin?
I have a 335-h3 that I would like to use 138 thread on it and equivalent to side 22/23 needle like I use on my Juki lu563 … is this possible