Marine Caulking~ Which One Do I Use?
Vložit
- čas přidán 30. 06. 2024
- www.boatworkstoday.com
There are a lot of different caulks that you can use on your boat, however using the right one can make the difference between your efforts paying off, or just getting pi$$ed off :-) This episode goes over the types of caulking I use most often, where I use them, and why.
Used 5200 to seal a jackplate on a high performance hull. Fanatically cleaned gel coat and aluminum, applied a 5/16" bead upon initial installation.
A 400lbs engine and a 9" jackplate, the 5200 easily supported the engine with all the bolts removed two years later upon removal.
With a hoist, we could lift the 550lbs hull & single axle trailer off the ground on the 5200 bond alone. It's bad serious stuff, so as he said, consider it permanent.
Thanks so much for making this video - very well explained. I'm refurbishing a camper high top on an old ford and I need to seal some gaps where a gasket seal or a butyl tape had been. Someone recommended the 3M 4200 to me among various other products but I was a little clueless on the difference in the varieties of sealants, adhesives, silicones, bedding and glazing compounds. So, after watching your video I think the 4000 may be my best bet as it waterproofs well but it doesn't adhere so strongly that it'd be an inconvenience to remove for repair or what have you.
P.S. The first person I asked about my project recommended silicone! I'm so glad I didn't take his word for it - now I know silicone's proper application and all the difficulties that go along with it's removal.
Thanks!
thank you so much for this video brother! I'm working on a 1644 jon boat and wasn't sure about 5200 to help seal rivets...but now I know it will do the job.
Another great vid Andy, thanks for the info! We're looking for below the best below the waterline bedding/sealant for our (weird) rudder. Thought 5200 would be the play, but now, thanks to you - planning on 4200 👌
Good advice Andy - great quality video and sound.
Thank you for taking the time to clarify the use of these sealants. Very nice shop!
I'm gonna share my secret weapon for removal of deck fittings which are bedded in with 3m 5200.
"Steel guitar string".
Use the thinnest steel string, (.006"), wrap the ends around two 1 inch diameter wooden dowels for handles. Remove the hardware from the cleat or whatever, and pull the string forcefully between the cleat and the gelcoat. It will part the 5200 like a cheese slicer.
No damage.
Try it and share with your viewers!
Works best when that stuff is warm. In cold weather kinda use the string as a saw to produce heat. Hundreds of auto windshields in my life have been cut out that way.
Thanks for the advice 😃👍🏻
No kidding! That's what they use to remove car windshields
Ive heard other boaters using braided fishing line also
You mean a garrote... lol
Always very instructive videos.
Thank you for posting and keep em coming!
I use Sikaflex which I have found works well. I think most boat restorers use Sikaflex in Italy and Europe.
Greetings from Jens in Italy.
A big thank you for your awesome video.. very well explained. Definitely picking up 3M 4000UV. Have a great summer!
Those kind of windows can be a little tricky to seal as there is actually 2 things that need to be addressed. The glass onto the boat then the frames onto the glass. First I would try to use the Dow Corning silicone from my video and glaze around the outside edge of the frames as well as the inside edge where the frame meets the glass. Tape off all edges leaving an 1/8" reveal on each side apply a bead of caulking and smooth over with your finger then pull the tape right away.
I worked for Ericson Yachts for 16 years. We had problems with leaks and tried using 5200 urethane compound, along with some others. The 5200 was a big problem as when a hardware change came through we could not get the part off of the glass without tearing the fiberglass of the hull or deck. The exception would be a hull to deck joint. I would not use it for a bolt on keel as there are cases when keels need to be removed, such as damage or design change. The bedding compound we found was a polysulfide compound such as Life Caulk by BoatLife or others. It makes an excellent long lasting waterproof joint that remains flexible and it can be removed without damaging the boat.
Excellent presentation! well explained and well recorded and very informative.
Either one of those would work equally as well. One other suggestion I would offer might be to use one of the Dow Corning Silicones (795 or 791) as you can get those in colors that may match up better to the car :-)
I'm coming rather late to your site but am finding it very helpful. I totally agree with your choice of sealing/bedding materials but have one observation about silicone removal: I believe 3M or some other company makes a softener chemical which greatly facilites the removal of silicone products. Best regards and, obviously, keep up the excellent work.
There are a couple of different styles of chainplates; some are for the stays which can be thru-bolted on the hull and the other is for the shrouds which usually are bolted onto an interior bulkhead. There are other ways that this is done, but generally I think that 5200 would be a good use for this as they are something that isn't removed very often (and a little extra bonding strength certainly isn't going to hurt :-) Hope this helps!
~Andy
Great job. Cleared up a bunch for me. Thanks.
Excellent information and presentation. Thank you Sir!
We have a small motorhome that I would like to keep in good shape. Winnebago provides a list of the ceiling stay use but they aren’t lasting long and might not be the best choices.
I’m assuming that since most of the surfaces are plastic you would recommend the Dow Corning silicone sealer for that and perhaps only use the 3M 4000 as a bed and compound that gets capped with another sealant.
There’s another sealant called Geo cell that’s very popular but it seems to have some problems with remaining tacky and attracting dirt.
Thanks for the great video, it’s really helpful!
That being said because they are mechanically fastened really any of the compounds I mentioned (other than the silicone) would be a great choice!
Thankyou, you just answered my question, the 5200 to re attach the top half of my hydrocycle to the bottom half. I don’t see it needing to be apart ever again after I fix things...
Andy, I already have the frame out and the glass out of frame also, so I will be starting from square one. I need to clean up glass and frame, which is wood. After that, ready to put back together. Thanks
If that doesn't take care of it then you'll need to do a full blown re-seal where you remove the frame and glass and start from square 1. If you end up having to go this route please let me know and I'll give some more detail on this process :-) Good luck!
Thanks for this great video!
Thank you. Nicely done, as always. But why no mention of butyl tape as a bedding compound for deck hardware? Doesn’t it far exceed the 10-year service life you mentioned for the 3M products?
I found rain gutter silicone to be easy to work with and durable. I used it to seal the rub rail. There is something that sticks to silicon and that is dust, which is the downside to this product.
Thank you for the information ;). I'm looking to re-bed my deck and transom hardware as well as my rub-rail. I think I'm going to go with the 4000 UV for the deck and transom hardware as it will be semi-exposed to UV. I'm probably going to use the 4200 for the rub-rail because it's not exposed to UV and I would still probably want to be able to remove it to re-do it at some point in the future.
Hi BWT, first of all congrats for your work! For the last eight years I've been rebuilding an old and initially destroyed 32' sailboat. Unfortunately, I'm in Brazil and we don't find all those incredible things you get in the US. My question is: would Sika 291 work as well as the 3M 4000 UV for resealing my toe rail? Thanks a lot, man!
thanks for the info. very helpful.
Great channel. Thanks for all the great videos !
I am a new boater. Just bought my first older fiberglass boat. There are holes in the transom from a sounder as well as bracket mount (through the transom) . Which sealant would you recommend? Sikaflix? 3m 4200 ? I may need to remove bracket later so would not use 5200.
Thank again ....bell rung !
Great video, thanks.
I always walk away with something useful watching your channel. I can't say that about all channels I watch. Thanks.
Nice video. Good info. Thanks
Love the guitar intro 🎸
Your videos are GREAT! you explain things so well, I am pretty confident I will be able to fix a couple soft spots on my deck this coming spring. I was looking into removing my bow pulpit to get it re-welded and noticed I am getting a lot of leakage at the trough bolts so I will need to start removing things and re bedding them. Im sure it is WAY over due. I plan on using the 3M 4000 UV, but I wanted to know your opinion on butyl tape? thank you again for your videos!
James Alberding Given a choice between a good caulking or butyl tape, I'd go with the caulking (it lasts longer imo)
Iam confused , cool kind a got it going to be doing hatches n hardware n up grading n got so many more questions as they pop up cool thxs , Scott
I really like your videos! What would you recommend to seal tempered glass to the wood frame, these are large windows aprox. 28x40 in the front of the cabin on my Hardin 44 , the glass sets into the frame from the inside and then a wood trim frame is installed around the perimeter of the glass to hold it in. I think I need something that can adhere to the glass but also seal it in, hoping to stay away from silicone due to the clean up factor.The glass is exposed to sunlight most of the time.Thank you!
Great video but I am a little confused I'm going to install a transducer on the back of my boat which will be below the waterline I am not sure which product to use do I just seal around the transducer or do I dip the screws in it also
Hi Andy, great stuff as usual. Would 4000 uv be appropriate to use for wood deck seams? Fir deck beams, and be nice if they would stop leaking.
Hate to say it but probably won't have the opportunity. I don't work much on alum boats (other than painting). But one suggestion I do have for resealing is to look at a product called Gluvit. Sealing seams and rivets is pretty much what this stuff is used for (5200/4200 probably would not be the best choice). There's lots of info on this product, a quick Google search will have you reading for hours :-)
I love your video! Your the 🐐
I greatly appreciate the class on compounds, especially as I prepare to put 12 plastic portlights back into my boat. I don't understand, however, what you meant about using both silicone and a bedding compound when doing portlights. Not sure how you can use both? Do you mean only using silicone when applying the plastic trim ring to the plastic port frame?
I just replaced the portlights on my Santana 2023 using the Dow Corning 795. Great suggestion. The smoked Lexan look great with the black 795, Messy but worth the extra effort and time. However, what would be wrong with using Butyl to bed down deck fittings as opposed to 4200? Thanks for your tutorials!!
Thanks for the info Andy. Very helpful, as always. Do you have any experience with butyl rubber for deck hardware, something that stays playable and does not harden or crack?
Love the videos, you clearly put a lot into them - lucky for us! We get a lot out of them.
I have a question about caulk.
Problem description: I have a catamaran and she is flexible (built that way on purpose). There is a joint between the 'hard bimini' and the coach roof that is about 1/2" wide. The boat came with some horrible caulk that took me forever to remove. I filled it with... 4000? I think. It is pulled away from both sides of the joint and has gotten pretty hard (probably why it pulled apart).
Is there something you recommend for filling large joints that will remain flexible in the face of large moving pieces of fiberglass.
I do not want to overstate the case, it doesn't flex massively, or even noticeably, but this is a 'lightly built' cat.
I understand if you haven't the time for this, but I though I'd take the chance! Thanks again for the videos!
+Cap'n Jan It's a silicone (which I normally don't like) but Dow Corning 795 or 791 is awesome stuff and would likely work well for your situation :-)
1 quick Q; was the glass originally mounted with a type of caulking, something that appeared to be a type of tape or was there some hard / brittle residue left behind on the perimeter of the glass? There are a few different ways these portlights were mounted. Once I know I'll be able to point you in the right direction :-) If it would be possible a quick pic can be sent to my email address. Visit my website About Us --> How To Reach Us :-) Thanks!
I just thought I'd let you know that boat is beautiful and I have close connections with Kid Rock and he would love that boat! He takes me out in his wood boat that says cowboy on the back!
+MN IceFisherman Well, have him look me up if he needs any work done ;-)
3M seems to be the common sensical approach to caulking, but I was told that some people in Northern Europe caulk folk boats using rotted tree trunk gunk produced from the oak tree. The idea is to intentionally rot a tree trunk in a riverbed nearby for I'm guessing here, 1 year??? and use the rotted core of the tree trunk to produce some kind of black material used to caulk the boat. I'm wondering if it can be combined with other material to produce a really decent caulking material.
what would you use to fill the pre-existing holes of a rub rail? Also, what would you use to seal the gap between the molds of the hull under the rub rail?
What a good info thanks!
As a brand new sailboat owner, love this channel. So do you prefer the 3M bedding compound over butyl tape for hardware, etc. on the deck? I've had a lot of sailors recommending the tape so just curious your thoughts. Thanks again!
I'm new to your channel and new to boat ownership. I just bought a 42ft Californian LRC. Basically all the windows need resealed and the fly ridge deck is a little flexible. Any advice you can give us? Thanks 😊
Just curious your thoughts on the following boat subfloor installation. Looks like a disaster waiting to happen. Thanks!
I have an old Coleman pro XL. It is a small pond boat and it has a black rubber or vinyl ‘ring’ around the boat holding the two pieces of the boat together. It is only stapled in which does not help with water getting INSIDE the pontoon part of the boat. I went to bass pro years ago and got some $$$ stuff and it worked GREAT. Don’t remember what it was though. I’m going to try the Dow Corning 791to try to seal that piece. The stuff I got from bass pro is still on there and holding up VERY GOOD but I still need to do the bottom of that ring. What do you recommend?? I used some of the lower grade silicone and now I have to remove and go with something better. Probably something these guys recommend.
Thanks for sharing
I want to adhere polycarbonate to gelcoat or fiberglass resin, silicones only?
Thanks for your comments Andy?👍🏻
Hey great video. I have a question I was wondering how to get a smooth finish on chop strand
if you're working with plexi (aka plastic), you'll want to use a good silicone. Dow Corning 795 or 791 :-)
Confused - to "bed" my 6" plastic deck plate, should I use DC795 (between fiberglass and collar) or should I use 3M 4000UV?
Andy, I am redoing a old Carver 2885, It has wood frames around front windows, what would you suggest to use rebedding them? Thanks, enjoy your videos.
what would work best for stopping the leak along the bow seams on my aluminum Jon boat. there is a keel cap along the middle about 1 1/4 inch wide with a seam along each side of it about 4 ft long. This is a welded modified-V Jon boat with 0.10" thick aluminum. apparently some of the bow's welds or aluminum cracked. The inside of the boat bow is covered with foam encased in aluminum, or I would weld the cracks.
Hi, I just purchase a cat and for transport the removed the windscreen that was attached with screws and black silicone I have managed to remove it all from the glass console and aluminum windscreen frame from what i read here on all different situation advice I'm guess to say that using 4000UV will be correct? Loving the videos it will help a lot now that I own a glass Cat power boat.
Hi Andy, what do you use to clean up silicone from fibreglass and plastic windows? Are you sanding to clean off all the silicone or using a solvent and if a solvent, then what?
Silicone for all plastics, or just polycarbonates? I need to repair a sailing dinghy mast that breaks down into three pieces for transport. At the end of each section are black plastic fittings that need replacement. Someone suggested adhesive instead of the original aluminum rivets. The point is to seal it for buoyancy and corrosion protection. I presume they are ABS. I'll try to confirm. Can I use the 4000 UV for that, or is it silicone for all plastics? Thanks for the videos!!
Hi there- thanks for the great video. So I have flush mount deck lights (plexiglass) NOT in a frame, bedded to the deck. As per your video, I'm confused if I should use the bedding (for sealing) or the silicone (for adhering to Plexiglass)? Advice would be appreciated!
cheers
Hi great interesting video, I need a bit help cause i been trying to watch a couple of videos to reinstall the centre window on a Stadline 38. The boat hull is steel. All painted by hampel paints 2 packs. I changed the centre window about 2 years ago. The window is made of perspex. First time i did it with car windscreen sealer and second with wurth product. So summary Need to install a perspex window to a steel frame. Whats best to use. Locally I can only find Dow 791. Watched also your other video where you install the hatch using Dow 795 for the perspex and 4000UV for the frame. The only thing is mine do not have a frame.
Try using the Black PL Loctite roof and flashing polyurethane. It is softer than 5200 so it gives more when things move.
Home Depot sells it, and I pay $5.85 per cartridge. Waterproof and UV resistant. I found it sticks to plastics. I think the silicone sticks to plastics since it is very flexible, the Black PL is also very flexible.
Being a polyurethane paints will stick to it. This stuff is easy to work, cleans up well with rubbing alcohol or dish soap.
+sdowney717
And I also use it underwater, 5 years no leaks at all. This on a 37 foot Egg Harbor wooden boat..
picasaweb.google.com/105248911187594415233/EggHarborHauloutJune242014?authuser=0&feat=directlink
sdowney717 In the FWIW department, for the realistically small price difference, I wouldn't use the PL products below the waterline! (3M polyurethanes are made in black, too.) I do use PL or locktite hardware store polyurethane caulking as adhesives and sealants extensively for everything from after welding floorboard replacements in a old jeep to residential carpentry - even on boats - for actual marine stuff like fittings and through-hulls, below the waterline: why be the guinea pig?
Very informative video, thanks. Got a real dumb question for you. I bought a boat that has a keel guard on it, and it's lifting in a couple of places (less than 6" long each and not fully lifted). Instead of going through the hassle of pulling it off and trying to get rid of all the adhesive, plus spending about $180 on a new one, I am wondering if I can use any of these products mentioned (except the 5200 LOL) to squeeze some in the gaps and hold the keel guard on the boat?
Got my questioned answered. Called the manufacturer of the keel guard. They had an immediate answer. West Systems 610.
rob1958bc Sorry I didn't get back to you in time; I usually try and get caught up on messages Sunday mornings :-) Glad you got it sorted out!
Andy, on a bronze through hull fitting you would use 3 M 4000 instead of 5200?
Good information video. Thanks!
+Lew Gresham I would either use 4000UV or 4200. Not 5200
I know this might a be about of topic but since ya know so much about sealants and adhesives, could ya help me figure out what would work best to reahear the sole to a boot or shoe? I know it's not boat related, but it needs to be flexible, and be able to stick to rubber.
Tough question.
I have an inflatable boat all shot out but it still has a few seasons left in it. The cone area in the back the fabric is showing. What’s a good solid sealant that’ll not be sticky when dried but flexible when folded.
Thank you.
Hello Andy,
I just used a 5200 to reseal the connection of the keel and the hull on the sailing boat, but after a short time a lot of bubbles appeared underneath the sealant! What could be the problem? It was sanded nicely and cleaned with acetone before 5200 was applied!
Ok, still confused on an application. I'm re doing a Mako 210 fuel tank. What do you suggest I use to reattach coffin cover to deck? 4ooo first then set in cover screws then 4000 uv?
Very nice video and despite listening to everything about silicone I’m still tempted to use it to fill a small very thin bead along the bottom of my consul because the 4000 UV deteriorated started to crack out and the silicone comes in a gray that matches my consul in my floor gelcoat instead of a bright white I’ll be at Thinline. Any reason I should do this on a bay boat and what about the mildew resistant characteristics of Dowell 795. Thank you
I have sheets of 3/4" thick Polly. I am wanting to use strips of it as chine guards on the bottom of my fiberglass covered wood Dory. What type of glue/ sealer would you recommend?
Hi great video. Hey i plan to attach the water drain plug housing(In side the boat just below the bottom of the transom of my rib fibreglass boat.Do i use silicon base or 4000 or 5200 as this is going to be a permanent fitting. Thanks and looking forward to your knowledgeable reply.
Thanks for the info. What would you recommend for sealing old transducer screw holes that dont go all the way through the transom. It is a 1990 Seaswirl Cuddy
I'd skip the sealant and go straight to thickened epoxy ;-) If you use a plastic syringe (west system sells them), you'll be able to completely fill the hole. If you're looking to still use the holes and just need to seal them up, then either 4000uv or 4200 would be my choice. Hope this helps!
Hi Andy, wonder if you can give me some advice. I just installed quick release deck hinge mounts on my Crownline for the bimini top. I had to drill four holes for #10 screws to install. How should I seal the screw holes against water getting to the core? Thanks, and love this channel!
I'd use 3M 4200 as the sealant for something like this. Get some in the hold, a little bit around each of the holes as well as the underside of the screw so it seals onto the hardware when tightened down. Clean up any excess right away and call it good :-)
Outstanding. Thanks so much for the reply! I was actually waiting to hear from you before doing anything.
Which sealant would be best to seal a toe rail to the deck and all other areas of wood to fiberglass? Thanks
I am re-bedding the 3 front windows in my salon on a 35' flybridge. It looks like I'll need to re-bed the tempered glass panels into the frames which I believe are plastic, and then re-bed that entire assembly into the actual boat. Do you recommend silcone from glass to frame, and bedding compound from frame to boat? Both products need to be black in color. I know in the video you discussed using silicone with Lexan but with the glass panels I wasn't sure. Thanks!
Whenever one of the surfaces is plastic, use Dow Corning 795 silicone. It's only when working with metal that I switch over to 3M 4000UV or 4200.. Hope this helps!
I'm not bedding hardware I'm not putting in polycarbonate. I need to reseal my center console to deck. It was holding my console well with 90% of the screws loose. It appears silicone was used in the past since the remaining product is kinda rubbery and I was able to knife through it quite easily to split the seal. It was holding a lot of force while crashing through the waves. What do you use for this? I will be reinforcing the deck holes and re pilot drilling so the screws and washers get a bite I will also try to through-bolt where I can.
hi thx for sharing the info, what would be best for an underwater metal and plastic bond?
3M 4200 may be great, but once opened it cures in the tube in 24 hrs! A pretty major limitation, at least for me who don't do this professionally, just fixing minor things on my boat. Is 4000UV the same?
I cannot use screws or bolts to mount devices. Need a spacer I can use screws on. Looking for what of bonding sealant? To use?
Questions if I may
#1 sail boat interior above water line. I need to mount 4x4 inch squares of wood 1x4 pressure treated wood.(if this is exceptable to use) to mount a battery switch or terminal bars. In one case it would
Be wood to wood in another case it would be wood to fiberglass. I need the wood block to use screws to hold device on.
Or should I do it another way with other than wood. Thank you
Mike
Which compound would you recommend for a drain plug and thur haul drains?
Adding wheels to a inflatable boat, if the transom is plastic with metal bolts. What do you use? How about wood transom to metal bolts? Mostly used in freshwater but some saltwater as well.
What would you use to place perspex direct without a frame? I am tired of leaking portholes and converting to cut perspex portlights. No frames. Steel hul with epoxy paint.
I have a couple of small spots that I need to fix on the bottom side of my boat, I was not looking to repair the fiberglass just cover it with one of the adhesives that you mention in your video. The scuffs are through the gel coat but not the fiberglass. Would using the 5200 work for this application? In the future, I will be getting the bottom re-gel coated but not for some time to come. I was just looking for something that I could cover the scuffs with that would protect the fiberglass and not come off when in the water. Thanks, RG
rundmm I'd suggest if you're looking for a 'quick and dirty' patch for the time being, try using Adtech p-14 filler. It's basically a fast cure gelcoat that is very easy to use / apply. Down the road when you are able to do a proper repair, there won't be any caulking to remove making life a lot easier :-) Hope this helps!
You didn't give any differences between the 4200 and the 4000 UV, yet you prefer the 4000 UV, is there a difference? On a wood boat I want a watertight seal where the garboard plank meets the keel, but have to always consider having to remove that plank in the future. Which is better to use, 4200 or 4000 UV?
Great. So what should I use when say bedding a new winch or cleat through the deck? Many people say to first drill larger holes, fill with epoxy, then cure, then re-drill. What is you advice on this? Always seems like a waste to buy epoxy in large quantity for a small job. Is there an easier way that would still protect core?
Pre-drilling and filling with epoxy is never a bad idea, but one that few people do. If you're using a good compound such as 3M 4000UV for metal and wood OR Dow Corning 795 for plastics you should be perfectly fine. The trick is to catch a problem before anything happens. Compound has a usable life of around 7 -8 years before it starts to break down and potentially fail. Plan on re-bedding hardware every 5-6 years and you won't have any problems :-)
Which 3M product is most similar to Sixaflex 291, and what do you think of the Sixaflex product?
And what about Urethan's, Polymers, Hybrid Polymers, Co-Polymers & Terpolymer's like NPC Solar Seal #900, ChemLink NovaLink, TiteBond Ultimate MP, CP1, Geocel 2300, MasterSeal NP1, SikaFlex & Lexel?
Hey, love the video's. Question, I have a plastic "cap" that covers the top of my transom on the back of my boat that is coming loose and I want to re-seal it so water doesn't get down inside. its an outboard and this cap is only about 20 inches long and comes down about 2 inches inside and outside.
would one of these work? do you recommend something else? thanks and keep up the great work.
+dankbobby Any of these (other than the silicone) will work just fine. Goober it up, place the cap and clean up the excess caulking :-)
+BoatworksToday Thanks for getting back to me, I will take your advice. Peace
What would you use to install a leaning post at a helm
Question here. Why do they use Dow 795 on glass buildings if it's mostly good for plastics and not so uv resistant?
GREAT video. Thank you!!!
Question I have a seam that is filled with Sikaflex now and needs to be pulled out and replaced. What product is best it has to be water tight.
Any possibility of posting a video of resealing a 14 aluminum boat with 3m 5200/4200?
what do u recommend for sealing a residential rain gutter ?
Thank you for sharing your knowledge in this arena. I am a new owner of a 1997 Hunter 376 and have a problem with water trickling down the compression post inside the cabin after it rains or even a good wash down. The boat has a deck stepped mast. I was thinking of using a caulk to go around the bottom of the mast where it meets the deck to seal this off. Am I thinking correctly and what product is best for this application?
Matt Cokee best thing would be to remove the mast step, clean and re-mount with new caulking. I'd personally go with 3M 4200. Just going around the perimeter isn't really going to do much; think of it more like a band-aid and not a 'fix' :-)
BoatworksToday I understand but removing the mast step is going to be expensive and I don't really have the resources to do that right now. Thought a good caulk around the base would fix my problem, even temporarily.
Matt Cokee It would definitely help, but the thing to remember is that it would be a temporary fix. Also, I'd pull the mounting bolts one at a time, put some caulking around the inside of the hole and re-mount. This can be done without pulling the mast :-) I'd still use 3M 4200
Very good intelligent video.
What can I use to repair the bottom front edge of the keel?