Thank you... I checked those wires a dozen times and nothing happened... Watched your video and decided to give them one more try... Bingo!... I was just getting ready to remove the starter and you saved me from that task!
I have a different model mower so I didn't have the layout of parts you do but you gave me a huge clue on what to do! I got mine started because of your video, thank you
Thank you! I tested and tried everything I could think of and nothing worked for me, cleaned my solenoid connection after watching this and it worked! 🤦♂️ thanks for the video!
Thanks! I too had just gotten a Husqavarna on the cheap and it doesn't turn over or anything and just ordered the ignition switch and also just bought new spark plugs and will try this out as soon as I can! Thanks a bunch, man! Rock on dude! #DogeDope
I found an easy way around the safety switch. I got a new switch, unplugged the wiring harness from the old one - which I left in place - and plugged the harness into the new switch. Then I wired the bottom plunger closed, and now it works dependably every time. I no longer must depress the clutch/brake lever in order to start the engine.
Husqvarna blown fuse is probably a pinched headlite wire or the wire tie down dry rots cracks off and melts the head lite wire on engine. That blows fuse and causes no start. So check the insulation on the head lite harness
I always check simple stuff first. Worked great last time so I'm hoping it's easy fix. Going check fuse and solinoid connection when I get home. I put new voltage regulator on it last year. I will check that also. Turn key to nothing so I'm hoping it will fire when I get home. Thanks 🙂
So I bought mine a few days ago and it started and ran and cut fine when I bought it only thing I didn’t do was test pto which turned out to be fine I went to cut my grass yesterday and no crank no start I hooked a jump box and jumped the solenoid with screw driver and it fired any tips?
Ive had the same problem with 2 different models recently. It seems to be a common problem on these Husqies....what could be the common causes of so many shorts?
My Husqvarna's switch on the "clutch" pedal (must be depressed to start) is the problem. I can re-seat it and it functions normally. But it is undependable and intermittent. I wonder if the switch should be replaced? It's a 2017 24V48 with only 83 hours.
I have had the same problem and I finally reached under the mower in the area of where the clutch (brake) petal interlock is and pulled out a lot of grass, a few sicks and dirt. After that the mower cranks and starts and runs fine. This has happened more than once and each time cleaning under the mower in the area of the start interlock has fixed it....
Mine is a 2019 YTH24V54, hopefully this is what's happening to mine. One day after two weeks of not being able to use it, I tried it for the heck of it and it cranked. So, I did the lawn since it was running. Then a few days later, thinking it would crank, I got on it and nothing again. I changed the ignition switch, the seat switch and charged the battery ovwr night but nothing happened. Someone suggested that the starter might be bad, but the lights don't flicker when I try to crank.
Loose connection wiggle harness in different areas turning the ignition over after each wire wiggled. 1st do the connectors then isolate the wire when u find which connector wiggled starts the engine could just be corrosion on the spades in connector scrap each spade and add dielectric conductive grease to prevent the corrosion Originally they plate the spades and females but heat and condensate in time causes the plating to wear off n then corrode
Let me start mower was running in park. I walked away and it died. Nothing I checked the connections all seems ok When i jump the solinoid the mower turns over. I am at a loss.
I put in a new battery, starter, spark plugs, fuel filter, drained old fuel. Still nothing from the keys. The engine doesn't turnover when I jump the solenoid either. The starter just spins. I'm thinking it may be a bad ignition switch? Let me know if you track your problem down. Mine was running, then started surging before it stalled out and didn't turn back on.
@@JagexAnarchy I haven't done mechanic work in yeas but if the starter is spinning and the engine is not tuning over then the starter is not engaging. It sounds like the solenoid might be bad. I don't know how much they cost but you have gone this far you might want to replace that. It could be the ignition, you might be able to jump that. In the one I am working on there are other switches that could cause it not to start like the one under the seat. There is a neutral safety switch that could be bad. I haven't gotten to either one of those yet. Have you checked the ground from the battery to the chassis where it bolts to the chassis? If it is really dirty, a bad ground can cause the problem also. I took the one off the one I am working on and cleaned it all up but it is not that. I would do that before continuing to eliminate that. This is the first mower I have ever looked at, in the past with cars, when the starter would spin and not engage it was always the solenoid. I don't get up to my buddies house much but when I do, if I find the problem I will get back to you. My buddy has no clue how to use a multimeter so he is counting on me. I hope not to let him down. Any bad ground may cause the problem. Look for broken or frayed black wires. I hope this helps?
Thank you... I checked those wires a dozen times and nothing happened... Watched your video and decided to give them one more try... Bingo!... I was just getting ready to remove the starter and you saved me from that task!
I have a different model mower so I didn't have the layout of parts you do but you gave me a huge clue on what to do! I got mine started because of your video, thank you
Thank you! I tested and tried everything I could think of and nothing worked for me, cleaned my solenoid connection after watching this and it worked! 🤦♂️ thanks for the video!
Thanks man! I’ve been using my push mower and frankly I can’t do another summer of that in the backyard. So I’m trying this out for sure!!
Zulu Wanga
46 seconds ago
I have a Husqvarna YTH18542. It wouldn't even crank... I tried what you did, and it worked. Thank you
Great!
Thanks! I too had just gotten a Husqavarna on the cheap and it doesn't turn over or anything and just ordered the ignition switch and also just bought new spark plugs and will try this out as soon as I can! Thanks a bunch, man! Rock on dude! #DogeDope
This is what I'm going to try next thank you good video
Thanks for the simple video
Same problem, but located in different location
gonna check the connections.. thanks for the tip
Thank you ended up being SAME issue! 👍🏼
Good video and nice kayaks!
I found an easy way around the safety switch. I got a new switch, unplugged the wiring harness from the old one - which I left in place - and plugged the harness into the new switch. Then I wired the bottom plunger closed, and now it works dependably every time. I no longer must depress the clutch/brake lever in order to start the engine.
Thanks, that was the problem!
Husqvarna blown fuse is probably a pinched headlite wire or the wire tie down dry rots cracks off and melts the head lite wire on engine. That blows fuse and causes no start. So check the insulation on the head lite harness
I always check simple stuff first. Worked great last time so I'm hoping it's easy fix. Going check fuse and solinoid connection when I get home. I put new voltage regulator on it last year. I will check that also. Turn key to nothing so I'm hoping it will fire when I get home. Thanks 🙂
Hey now you have a new battery and you figured it out without taking it to the shop
So I bought mine a few days ago and it started and ran and cut fine when I bought it only thing I didn’t do was test pto which turned out to be fine I went to cut my grass yesterday and no crank no start I hooked a jump box and jumped the solenoid with screw driver and it fired any tips?
Ive had the same problem with 2 different models recently. It seems to be a common problem on these Husqies....what could be the common causes of so many shorts?
Thanks ❤
So mine was running and in the middle of the yard boom just stoped running i will look at these connections next.
I have new battery and it's not locked up. Going check fuse tonight.
So i cked all the connection
I will ck again
Batter good.
If i jump the solinoid the mower turns over.
I am at a loss.
How to replace fuse on solenoid wire to fuse
But why is the fuse blowing?
My Husqvarna's switch on the "clutch" pedal (must be depressed to start) is the problem. I can re-seat it and it functions normally. But it is undependable and intermittent. I wonder if the switch should be replaced? It's a 2017 24V48 with only 83 hours.
I have had the same problem and I finally reached under the mower in the area of where the clutch (brake) petal interlock is and pulled out a lot of grass, a few sicks and dirt. After that the mower cranks and starts and runs fine. This has happened more than once and each time cleaning under the mower in the area of the start interlock has fixed it....
Cheers
Mine is a 2019 YTH24V54, hopefully this is what's happening to mine. One day after two weeks of not being able to use it, I tried it for the heck of it and it cranked. So, I did the lawn since it was running. Then a few days later, thinking it would crank, I got on it and nothing again. I changed the ignition switch, the seat switch and charged the battery ovwr night but nothing happened. Someone suggested that the starter might be bad, but the lights don't flicker when I try to crank.
Loose connection wiggle harness in different areas turning the ignition over after each wire wiggled. 1st do the connectors then isolate the wire when u find which connector wiggled starts the engine could just be corrosion on the spades in connector scrap each spade and add dielectric conductive grease to prevent the corrosion
Originally they plate the spades and females but heat and condensate in time causes the plating to wear off n then corrode
Let me start mower was running in park.
I walked away and it died. Nothing
I checked the connections all seems ok
When i jump the solinoid the mower turns over.
I am at a loss.
Been there done that
should of , could of......
Working of a friends. He put in a new battery, new starter, new solenoid. Still no go. I am going to have to pull her apart and track it down.
I put in a new battery, starter, spark plugs, fuel filter, drained old fuel. Still nothing from the keys. The engine doesn't turnover when I jump the solenoid either. The starter just spins. I'm thinking it may be a bad ignition switch? Let me know if you track your problem down. Mine was running, then started surging before it stalled out and didn't turn back on.
@@JagexAnarchy I haven't done mechanic work in yeas but if the starter is spinning and the engine is not tuning over then the starter is not engaging. It sounds like the solenoid might be bad. I don't know how much they cost but you have gone this far you might want to replace that. It could be the ignition, you might be able to jump that. In the one I am working on there are other switches that could cause it not to start like the one under the seat. There is a neutral safety switch that could be bad. I haven't gotten to either one of those yet. Have you checked the ground from the battery to the chassis where it bolts to the chassis? If it is really dirty, a bad ground can cause the problem also. I took the one off the one I am working on and cleaned it all up but it is not that. I would do that before continuing to eliminate that. This is the first mower I have ever looked at, in the past with cars, when the starter would spin and not engage it was always the solenoid. I don't get up to my buddies house much but when I do, if I find the problem I will get back to you. My buddy has no clue how to use a multimeter so he is counting on me. I hope not to let him down.
Any bad ground may cause the problem.
Look for broken or frayed black wires. I hope this helps?
@@JagexAnarchy Sometimes when it is surging it is just running out of gas?