I appreciate your effort, sir. I have a OLED65B7A its flashing 3 times and turns off with a solid red light. I ordered and replaced T-CON, Mainboard, and PSU twice and facing the same issue. Do you think the panel itself has gone bad? Thanks in advance.
did you use the multimeter to check the voltages? if all exist an stable, the tv will give less then 5 sec to test each voltage before it goes off i did see 3 blinks linked to the power supply board issue,
@@SOSfixElectronics Correct i used the multimeter and followed your Volt chart on the PSU board. I have 2 PSU boards showing the same reading. Yes it gives less than 5 sec after pressing the power button and then the voltage drops.
@@faisalkhalid9659 good, check for short in 12v and 24v tcon input? check the tcon fuses? disconnect the screen flex cables one by one and turn on the tv each time and see if the tv will stay on longer or any change?
@@SOSfixElectronics Fuses are good and i was unable to find any shorts on the T-CON. I disconnected the flex cables one by one and one at a time as well, the result was the red light kept on and not blinking. Also tried the same process after replacing another T-CON card.
Got the same problem after same TV automatically goes to sleep mode. I disconnected all cables and power, then in 5 minutes connected the power, automagically it started to work. But next day the same issue, pretty bored. Any advices? I could change the power board myself (former iPhone repairer). Do you have PSU board model #?
@@SOSfixElectronics finally TV died. Going to check R7624 voltage according to service manual. How much it should be? BTW my TV plays audio, it’s discoverable on WiFi and works with remote, but no picture
Good day sorry I have this problem with 55EC930T-TA it click and show the power light and goes off and returns to the standby light please I don't know if there is any way can render possible solution please
Hi Brother .. i’m Having the issue on the same model that when i Press Power Button the RED light Blinks for 3 seconds then it’s Goes off … no Display no image … I measured the voltages and on P201 all voltages are Ok BUT on P202 there’s only 1 Volt on the 24VD Points
Grate fix
Thank you
No problem 👍
Amazing how a .01 cent capacitor can make a 1000 dollar TV useless . Good Fix
100 % right
i have oled 55e6v.. it has duble image flickering.. what can i do?
check the t-con voltages
I appreciate your effort, sir. I have a OLED65B7A its flashing 3 times and turns off with a solid red light. I ordered and replaced T-CON, Mainboard, and PSU twice and facing the same issue. Do you think the panel itself has gone bad? Thanks in advance.
did you use the multimeter to check the voltages? if all exist an stable, the tv will give less then 5 sec to test each voltage before it goes off i did see 3 blinks linked to the power supply board issue,
@@SOSfixElectronics Correct i used the multimeter and followed your Volt chart on the PSU board. I have 2 PSU boards showing the same reading. Yes it gives less than 5 sec after pressing the power button and then the voltage drops.
@@faisalkhalid9659 good, check for short in 12v and 24v tcon input? check the tcon fuses? disconnect the screen flex cables one by one and turn on the tv each time and see if the tv will stay on longer or any change?
@@SOSfixElectronics Will do and let you know. Thanks for the responses
@@SOSfixElectronics Fuses are good and i was unable to find any shorts on the T-CON. I disconnected the flex cables one by one and one at a time as well, the result was the red light kept on and not blinking. Also tried the same process after replacing another T-CON card.
Got the same problem after same TV automatically goes to sleep mode. I disconnected all cables and power, then in 5 minutes connected the power, automagically it started to work. But next day the same issue, pretty bored. Any advices? I could change the power board myself (former iPhone repairer). Do you have PSU board model #?
you need to get a multimeter and check voltages,
@@SOSfixElectronics finally TV died. Going to check R7624 voltage according to service manual. How much it should be? BTW my TV plays audio, it’s discoverable on WiFi and works with remote, but no picture
you have a place for me to buy a replacement board? thank you for this video.
ebay have them
@@SOSfixElectronics Did this tv have 3 red flashing when you started it up?
@@MrTrocks365 the tv tried to turns on then goes off, the red light was flashing but i didnt count it.
Good day sorry I have this problem with 55EC930T-TA it click and show the power light and goes off and returns to the standby light please I don't know if there is any way can render possible solution please
unplug the screen from tcon, if the tv stayed on it mean you have a faulty screen
Hi Brother .. i’m Having the issue on the same model that when i Press Power Button the RED light Blinks for 3 seconds then it’s Goes off … no Display no image … I measured the voltages and on P201 all voltages are Ok BUT on P202 there’s only 1 Volt on the 24VD Points
you can try to force the power to turns on the driver voltages 24V. check for short, disconnect the screen and try....
@@SOSfixElectronics i have already disconnected everything but there’s still no voltages any suggestions will be appreciated
Good day sorry I have this 55EC930T-TA
#Mr.#FixIt...
Wish I could send you my Sony oled a1e